Trotec PWLS 05-10 User manual

TRT-BA-PWLS05-10-PWLS06-10-TC2019-60-001-EN
PWLS 05-10 / PWLS 06-10
EN
OPERATING MANUAL
LED WORK LAMP

2 EN
LED work lamp PWLS 05-10 / PWLS 06-10
Table of contents
Notes regarding the instructions ..........................................2
Safety .....................................................................................2
Information about the device................................................4
Transport and storage...........................................................6
Start-up..................................................................................6
Operation ...............................................................................7
Errors and faults....................................................................8
Maintenance ..........................................................................8
Disposal .................................................................................9
Notes regarding the instructions
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
instructions must be observed.
You can download the current version of the instructions and
the EUdeclaration of conformity via the following link:
PWLS 05-10
https://hub.trotec.com/?id=44106
PWLS 06-10
https://hub.trotec.com/?id=44107
Safety
General Power Tool Safety Warnings
Warning
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from 8years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
The term power tool in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
General Power Tool Safety Warnings– Work area
safety
•Keep work area clean and well lit. Clutter or dark areas
invite accidents.
•Do not operate power tools in explosive atmosphere,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
•Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.

EN 3
LED work lamp PWLS 05-10 / PWLS 06-10
General Power Tool Safety Warnings– Electrical
safety
•Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
•Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
•Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
•Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
•When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
•If operating a power tool in a damp location is
unavoidable, use a residual current device(RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
General Power Tool Safety Warnings– Power tool
use and care
•Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
•Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
•Store idle power tools out of the reach of children and
Do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
•Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
•Use the power tool, accessories and tool bits etc. in
accordance with these instructions, Take into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
•Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
General Power Tool Safety Warnings– Battery tool
use and care
•Recharge only with charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when operated with
another battery pack.
•Keep the USB inputs closed with the rubber side cover
to prevent them from contamination. If you do not follow
this advice and the USB inputs become contaminated, it
might not be possible to plug in the USB charging cable.
•Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outsides the specified range may damage
the battery and increase the risk of fire.
•Keep charger and USB charging cable clean.
Contamination entails a risk of electric shock.
•Do not operate the charger on highly combustible
ground (e.g. paper, textiles etc.) or in an inflammable
environment. The heat generated by the charger during
charging entails a risk of fire.
•Only use the supplied USB charging cable by Trotec for
the devicePWLS 06-10. Do not use any other USB cables.
General Power Tool Safety Warnings– Service
•Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Intended use
Use the devices PWLS 05-10 and PWLS 06-10 according to the
technical data and only for a temporary illumination of indoor
and outdoor areas, e.g. for construction sites.
Foreseeable misuse
Any other use than the one described in the chapter "Intended
use" is regarded as reasonably foreseeable misuse.
Personnel qualifications
People who use this device must:
• have read and understood the instructions, especially the
Safety chapter.

4 EN
LED work lamp PWLS 05-10 / PWLS 06-10
Residual risks
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
Warning of explosive substances
Do not expose the battery to temperatures above 75
°C! Do not let the battery come into contact with water
or fire! Avoid direct sunlight and moisture. There is a
risk of explosion!
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Caution
Keep a sufficient distance from heat sources.
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Information about the device
Device description
The devices PWLS 05-10 and PWLS 06-10 are equipped with
light-intense surface LEDs.
You can select between a high or low brightness level for both
devices. Moreover, you can select the strobe mode. In the
strobe mode, a flash effect can be created which can serve as
warning, marking or defence function. Both devices are
equipped with a transport handle and a wrist strap attachment.
A magnetic holder is positioned on the wrist strap attachment.
The device PWLS 05-10 is operated with batteries. The batteries
are not included in the scope of delivery.
The device PWLS 06-10 is operated with an integrated battery.
The battery is built-in and can be charged via a USB charging
cable and a standard charger. The standard charger is not
included in the scope of delivery.
The battery status can be read on the battery indication (4 blue
LEDs).
The device PWLS 06-10 is equipped with a power bank
function.
Device depiction
Front view PWLS 05-10 and PWLS 06-10
12
No. Designation
1 Surface LED
2 Transport handle with wrist strap attachment

EN 5
LED work lamp PWLS 05-10 / PWLS 06-10
Rear view PWLS 05-10
36
45
No. Designation
3 On/off switch
4 Magnetic holder
5 Battery compartment cover
6 Battery compartment
Rear view and USB charging cable PWLS 06-10
7
10
812
9
11
13
No. Designation
7 On/off switch
8 USBconnection/ output
9 USBconnection/ input
10 Cover for USB connections
11 Magnetic holder
12 Battery indication (4 blue LEDs)
13 USB charging cable
Scope of delivery
PWLS05-10
• 1x LED work light
• 1x Manual
• 4x AA1.5V batteries
PWLS06-10
• 1x LED work light with integrated battery
• 1x Manual
• 1x USB charging cable
Technical data
PWLS05-10
Parameter Value
Nominal voltage 6V
Surface LED Power input 10W
Luminous flux 650 lm
Burn time high brightness
level
= 3-4h
low brightness level
= 9-10h
Colour temperature 6000K
Dimensions (length x width x height) 40 x 160 x 125mm
Weight (packaging excluded) 370g
Batteries 4AA1.5V
Runtime of batteries ≥3hours
Permitted ambient temperature (when
stored)
-30°C-75°C
Operating temperature -20°C-55°C
Type of protection IP44
Protection class III

6 EN
LED work lamp PWLS 05-10 / PWLS 06-10
PWLS06-10
Parameter Value
Surface LED Power input 10W
Luminous flux 800lm
Burn time high light-intensity
= 4-5h
low light-intensity
= 8-9h
Colour temperature 6000K
Dimensions (length x width x height) 40 x 160 x 125mm
Weight (packaging excluded) 434g
Length USBcable 0.8m
Nominal voltage USBconnection (output) 5V
Nominal current consumption
USBconnection (output)
1A
Battery type Li-ion
Battery voltage 3.7V
Battery capacity 4400mAh
Charging time 6-7h
Permitted ambient temperature (when
stored)
-30°C-75°C
Operating temperature -20°C-55°C
Type of protection IP 44
Protection class III
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
To make the device easier to transport, it is fitted with a
transport handle.
Before transporting the device, observe the following:
• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
• Switch the device off.
• Allow the device to cool down.
• Remove the batteries from the device PWLS 05-10.
• Disconnect the USB charging cable from the device
PWLS 06-10.
The supplied batteries are subject to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping batteries:
• The user may transport the batteries by road without any
additional requirements.
• If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.
– Only ship batteries if their housing is undamaged.
– Mask open terminals with tape and pack the battery in
a way that it cannot move inside the packaging.
– Please also observe any other national regulations.
Storage
Before storing the device, proceed as follows:
• Switch the device off.
• Pull the USB charging cable(13) out of the device PWLS
06-10.
• Allow the device to cool down.
• Remove the batteries from the device PWLS 05-10.
• Clean the device as described in the Maintenance chapter.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• Ambient temperature below 75°C
• protected from dust and direct sunlight
Start-up
Unpacking the device
• Take the device and the accessories out of the packaging.
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
• Check the contents for completeness and look for
damages.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
• Dispose of the packaging material according to the
national regulations.
Inserting batteries for PWLS 05-10
You need 4AA 1.5V batteries for the device PWLS 05-10.
Insert the batteries into the device prior to use. Please proceed
as follows:

EN 7
LED work lamp PWLS 05-10 / PWLS 06-10
1. Open the battery compartment(6) by removing the battery
compartment cover(5).
2. Insert the batteries with correct polarity into the battery
compartment(6) (+/-).
3. Close the battery compartment(6) by closing it with the
battery compartment cover(5).
ðThe device PWLS 05-10 is now ready to use.
Charging batteries for PWLS 06-10
Note
The battery can be damaged in case of improper
charging.
Pull out the USB charging cable(13) from the external
charger each time before switching the device on.
Never charge the battery at ambient temperatures
below -20°C or above 55°C.
Charge the battery of PWLS 06-10 completely before using the
device. Use the USB charging cable(13) and a standard
charger.
Proceed as follows to charge the battery:
1. Open the cover(10) of the USB connections at the back of
the cordless work light.
2. If applicable, plug the charger into the mains socket.
3. Put the USB charging cable(13) into the USB connection/
input(9) of the device PWLS 06-10 and into a charger.
ðWhen the battery status is very low, the charging time is
6-7hours.
ðWhen the battery is charged 25%, the first LED of the
battery indication(12) is illuminated in blue. When the
battery is charged 50%, the second LED of the battery
indication(12) is illuminated in blue. When the battery is
charged 75%, the third LED of the battery
indication(12) is illuminated in blue.
ðWhen the battery is charged 100%, the fourth LED of
the battery indication(12) is illuminated in blue.
4. When all LEDs of the battery indication(12) are illuminated
and the battery is completely charged, you can remove the
USB charging cable(13) from the charger and from the
device PWLS 06-10.
5. Pull the charger out of the mains socket.
ðThe LED work light and the charger may have become
warm during charging. Let the LED work light and the
charger cool down to room temperature.
ðThe device PWLS 06-10 is now ready to use.
Note
Note that the battery status of the device PWLS06-10
cannot be read while in operation. You can only read
the battery status while charging.
Operation
Tips and notes on handling the LED work light
General information:
• Avoid looking directly into the light source.
• Use the devices only for a temporary illumination of indoor
and outdoor areas, e.g. for construction sites.
• The devices PWLS 05-10 and PWLS 06-10 can be used as
strobe.
• The LED work lights are particularly suited for illuminating
larger areas.
Info
You can turn the handles of the LED work lights by
180° and set 6 positions.
Switching the device on and off
Switching the devices PWLS05-10 and PWLS06-10 on and off
works identically.
1. Press the on/off switch(3/7) 1x to switch the device on or
off.
ðOnce the device is switched on, the surface LED(1) is
illuminated.
ðOnce the device is switched off, the surface LED(1) is
not illuminated.
Setting brightness level and strobe mode
Setting brightness level and strobe mode works identically for
both devices PWLS 05-10 and PWLS 06-10
üCheck whether the batteries (standard or integrated) are
completely charged. If necessary, replace the batteries or
charge the integrated battery.
1. Set the lowest light intensity by pressing the on/off
switch(3/7)1x.
2. Set the high brightness level by pressing the on/off
switch(3/7)3x.
3. Set the strobe mode by pressing the on/off
switch(3/7)5x.
Always proceed in the same order to set the desired light
intensity or the strobe mode.
Note
By quickly pressing the
on/off switch(3/7), you can switch between the
brightness levels and the strobe mode.
Using the power bank
If you like to use the device PWLS 06-10 as power bank,
proceed as follows:
1. Put the USB charging cable(13) into the USB connection/
output(8) of the device PWLS06-10.
2. Then plug the USB charging cable into the USB input of the
device that you would like to charge.
3. Charge your device until it has reached the desired
charging status.

8 EN
LED work lamp PWLS 05-10 / PWLS 06-10
4. Disconnect the USB charging cable(13) from the device
that has been charged, and from the device PWLS06-10.
Note
The battery indication (4 blue LEDs) does not need to
be observed when charging an external device.
While charging, the battery indication (4 blue LEDs)
only displays the battery status of the device PWLS
06-10.
Note
Note that the device PWLS 06-10 discharges when it is
used as power bank.
Shutdown (PWLS05-10)
Warning of electrical voltage
Never touch the batteries in the battery
compartment(6) with wet or damp hands.
• Switch the device off.
• Remove the batteries from the battery compartment(6).
• If required, allow the device to cool down.
• Clean the device according to the Maintenance chapter.
• Store the device according to the Storage chapter.
Shutdown (PWLS06-10)
Note
Never touch the USB connections of the device
PWLS 06-10 with wet or damp hands.
1. Switch the device off.
2. Disconnect the USB charging cable(13).
3. If required, allow the device to cool down.
4. Clean the device according to the Maintenance chapter.
5. Store the device according to the Storage chapter.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
The battery does not charge:
• Check if the USB charging cable is plugged in properly into
both the charger and the device.
Check if the USB charging cable is properly connected to
both the contacts of the charger and the device PWLS
06-10.
• Check USB charging cable, charger and device PWLS
06-10 for damages. Do not use the damaged device
anymore if you detect any damages. Contact the Trotec
customer service.
• Check the fuse (home).
Note
The integrated battery might possibly be defective.
Contact the Trotec customer service.
The device is not lit:
• The batteries might possibly be empty. Replace them with
new batteries.
• The battery power might be too low. Charge the battery via
the USB charging cable and a charger.
• On the battery indication (4 blue LEDs), you can check
whether the battery has been completely charged.
• Check the USB charging cable for damages. If the USB
charging cable is damaged, stop using it. Contact the
Trotec customer service.
Note
The LEDs are possibly damaged. Contact the Trotec
customer service.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
Maintenance
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug of the charger with wet or
damp hands.
• Switch the device off.
• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
• Disconnect the USB charging cable.
• Allow the device to cool down completely.
Warning of electrical voltage
Maintenance tasks which require the housing to be
opened must only be carried out by authorised
specialist companies or by Trotec.
Notes on maintenance
The device does not require maintenance.

EN 9
LED work lamp PWLS 05-10 / PWLS 06-10
Cleaning
The device should be cleaned before and after each use.
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
• Clean the device with a soft, damp and lint-free cloth.
Make sure that no moisture enters the housing. Protect
electrical components from moisture. Do not use any
aggressive cleaning agents such as cleaning sprays,
solvents, alcohol-based or abrasive cleaners to dampen
the cloth.
• Dry the device with a soft, lint-free cloth.
• Keep the connecting terminals on the device and charger
clean.
• When you are currently not charging the battery, leave the
cover(10) on the USB connections. This way, no dirt can
enter.
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
In the European Union, batteries and accumulators must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.

Trotec GmbH
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
www.trotec.com
Other manuals for PWLS 05-10
1
This manual suits for next models
1
Table of contents
Other Trotec Work Light manuals
Popular Work Light manuals by other brands

brennenstuhl
brennenstuhl ML CA 120 F IP54 operating instructions

jcb
jcb JCB-WL-TUFFCLAMP Instructions & user's manual

REV Ritter
REV Ritter TWIN POWER Assembly and operating instructions

Näve
Näve 5195161 instruction manual

Philips
Philips iColor MR g2 installation instructions

Larson Electronics
Larson Electronics EPL-16C-1MLED-300 instruction manual