True Innovations 43506 User manual

Model #: 43506
EXECUTIVE CHAIR
1.To Adjust Seat Height:
While seated, lean forward and reach under the right
side of the chair to find the handle. Lift the handle and
raise your body up slightly to allow the chair to rise to
the desired height. To lower the seat, lift the handle
while applying weight downward on the seat. The
chair will descend until the handle is released or the
chair reaches the bottom position.
2.To Operate Tilt Lockout:
While sitting in the chair, the lever on the users left side
controls the tilt lock function. Lift up on the lever to
unlock the tilt function. The chair should tilt freely
through the full range of motion. Press down on lever to
lock the chair in any position. The tilt function can be
locked out in the full upright position, in full recline, or
any position in between.
3.To Adjust Tension on The Tilt:
Reach under the front center of the chair, grasp the
round knob and turn counter - clockwise to make the tilt
mechanism firmer (stiffer). To make the tilt mechanism
less firm, turn the knob clockwise until the desired
resistance is found.
4.To Adjust Mechanical Lumbar:
While seated, reach to the right side of the back
cushion to find the adjustment knob for the mechanical
lumbar. Turn the knob clockwise to increase the lumbar
support. To reduce the lumbar support, turn the knob
counter – clockwise. Turn the knob until the desired
support is reached.
OPERATING INSTRUCTIONS

Model #: 43506
EXECUTIVE CHAIR
Part #
Description
Quantity
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Casters
5 Star Base
Telescoping Cover
Gas Lift
Seat Plate
Arms
Seat Cushion
Back Cushion
Back Support Plate (already
attached to the back cushion)
1-5/8” Screws
7/8” Screws
1-1/4” Screws
2-1/2” Screws
Black Plastic Caps
Allen Key
5
1
1
1
1
2
1
1
1
2
2
4
4
4
1
A. Remove all parts from carton and separate them into part number groups as indicated in the parts list.
B. To begin assembly, place 5 Star Base (2) upside down and insert Casters (1) into bottom of Base (2).
C. Turn Base (2) right side up on the floor and insert Gas Lift (4) into center hole on Base (2).
D. Place Telescoping Cover (3) over the Gas Lift (4) and rest it on the Base (2).
E. Attach Seat Plate (5) onto the bottom of Seat Cushion (7) (with front of Seat Plate facing front of Seat Cushion) by
using 1-5/8” Screws (10) for front holes of Seat Plate (5) and 7/8” Screws (11) for rear holes of Seat Plate (5)
and tighten screws.
F. Align Back Cushion (8) with Seat Cushion (7) by positioning Back Support Plate (9) over the Seat Plate (5) with
1-1/4” Screws (12) as shown in Diagram 1. Do not tighten screws completely.
G. Place the assembled chair on top of Gas Lift (4) and press down until fully engaged.
H. Insert 2-1/2" Screws (13) into arm holes attaching Arms (6) to sides of Seat Cushion (7) and Back Cushion
(8). Now, tighten all the screws. Remember to tighten the back support plate screws also!
I. Place Black Plastic Caps (14) into arm holes once screws have been tightened.
J. Periodically (every 90 days) tighten all screws in the chair.
ATTENTION: Make certain all screws are fully tightened before using chair.
ASSEMBLY INSTRUCTIONS
PARTS LIST