True Innovations 44172 User manual

Item number: 44172
EXECUTIVE CHAIR
1. To Adjust Seat Height:
While seated, lean forward and reach under the
right side of the chair to find the handle. Lift the
handle and raise your body up slightly to allow the
chair to rise to the desired height. To lower the
seat, lift the handle while applying more weight
downward on the seat. The chair will descend until
the handle is released or the chair reaches the
bottom position.
2. To Operate Tilt Lockout:
While seated, reach under the right side of the
chair to find the height adjustment handle. Pull the
handle all the way out (away from the gas lift) to
allow the chair to tilt backwards. To lock the chair
in the upright or vertical position, sit upright and
push the handle in towards the gas lift.
3. To Adjust Tension on The Tilt
Mechanism:
Reach under the front center of the chair, grasp
the round knob and turn counter- clockwise to
make the tilt mechanism firmer (stiffer). To make
the tilt mechanism less firm, turn the knob
clockwise until the desired resistance is found.
4. To Adjust Mechanical Lumbar:
While seated, reach to the right side of the seat cushion to find the
adjustment knob for the mechanical lumbar. Turn the knob
clockwise to increase the lumbar support. To reduce the lumbar
support, turn the knob counter –clockwise. Turn the knob until the
desired support is reached.
Please check to ensure that you have received all the parts for the assembly of this chair. If you
find any missing or damaged parts, do not return to the store. UK customers are to call
0-800-051-6775 for assistance. Please note that a receipt is required for all warranty
replacements.
This chair has been tested and approved for normal use which is defined as a standard work
week of forty hours by a person weighing less than 250lbs (113kg).
Service hours are: UK Standard Time: 2:00 pm-1:00 am Monday –Friday.
OPERATING INSTRUCTIONS

Item number: 44172
EXECUTIVE CHAIR
A. Remove all parts from carton and separate them into part number groups as indicated in parts list.
B. To begin assembly, place 5 Star Base (2) upside down and insert Casters (1) into bottom of Base (2).
C. Turn Base (2) right side up on the floor and insert Gas Lift (4) into center hole on Base (2).
D. Place Telescoping Cover (3) over the Gas Lift (4) and rest it on the Base (2).
E. Attach Seat Plate (5) (with front of seat plate facing front of seat cushion) onto the bottom of Seat Cushion (7)
by using 2-1/4” Big Screws (9) and 7/8”Big Screws (10) tighten the screws.
F. Place the Seat Cushion (7) with Seat Plate (5) on top of Gas Lift (4) and press down until fully engaged.
G. Fasten Arms (6A & 6B) onto sides of Seat Cushion (7) by using 1-1/4” Small Screws (11). Do not tighten
screws completely.
H. Put Back Cushion (8) flat between Arms (6A & 6B), and use 1-1/4” Small Screws (11) to locate lower screw
holes on both Arms (6A & 6B) & Back Cushion (8) as Diagram 1. Push the Back Cushion (8) up to a vertical
position and attach the Arms (6A & 6B) by using 1-3/4” Small Screws (12) as Diagram 2. Tighten the
screws.
I. Place Black Plastic Caps (14) into arm holes once screws have been tightened. Please make sure to have
the groove of the caps to match the groove of the arms.
J. Fix the Adjustable Knob under the seat cushion by using 1”Small Screws (13) as Diagram 3. Tighten all
the screws.
K. Fix the cable for the Adjustable knob into the plastic clip attached to the bottom of the chair seat as Diagram
3.
L. Periodically (every 90 days) make sure that the screws are still fully tightened.
ATTENTION: Make certain all screws are fully tightened before using chair.
Part #
Description
Quantity
1.
2.
3.
4.
5.
6A.
6B.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Casters
5 Star Base
Telescoping Cover
Gas Lift
Seat Plate
Left Arm
Right Arm
Seat Cushion
Back Cushion
2-1/4”Big Screws
7/8”Big Screws
1-1/4”Small Screws
1-3/4”Small Screws
1”Small Screws
Black Plastic Caps
Allen Key
5
1
1
1
1
1
1
1
1
2
2
6
2
2
8
1
P A R T S L I S T
A S S E M B L Y I N S T R U C T I O N S