True Innovations 9534 User manual

Item number: 9534
M A N A G E R C H A I R
1. To Adjust Seat Height:
While seated, lean forward and reach under the right
side of the chair to find the handle 1. Lift the handle and
raise your body up slightly to allow the chair to rise to
the desired height. To lower the seat, lift the handle
while applying more weight downward on the seat.
The chair will descend until the handle is released or the chair
reaches the bottom position.
2. To Operate the Tilt:
While seated, lean backward and reach under the right side of the
chair to find handle 2. When the handle is placed in the level
position, leaning back to allow the chair to tilt backwards. Push
down the handle to lock
the angle while the desired position is reached.
3. To Adjust Back Cushion Angle:
While seated, lean backward and reach under the
right side of the chair to find the handle 3. When the handle is
placed in the level position, tilting your body backwards to adjust
the angle of back cushion, push down the handle to lock the back
angle while the desired angle is reached.
4. To Adjust Tension on The Tilt:
While seated, reach under the front center of the chair, grasp the
round knob and turn counter - clockwise to make the tilt
mechanism firmer (stiffer). To make the tilt mechanism less firm,
turn the knob clockwise until the desired resistance is felt.
5. To Adjust Arm Height:
Press the triggers on the front of chair arms to allow
the arms to move up or down freely then release the
triggers once the desired height is reached.
This chair has been tested and approved for normal use which is defined as a standard work week of forty
hours by a person weighing less than 225lbs.
Please check to ensure that you have received all the parts for the assembly of this chair. If you
find any missing or damaged parts, do not return to the store. UK customers are to call
0-800-051-6775 for assistance. Please note that a receipt is required for all warranty replacements.
Service hours are: UK Standard Time: 2:00 pm-1:00 am Monday –Friday.
OPERATING INSTRUCTIONS

Item number: 9534
M A N A G E R C H A I R
Back Support Plate Assembly:
A. Remove all parts from carton and separate them into part number groups as indicated in the Parts List.
B. To begin assembly, place the 5 star base (2) upside down and insert the casters (1) into bottom of the base (2).
C. Turn the base (2) right side up on the floor and insert the gas lift (4) into center hole on the base (2).
D. Place the telescoping cover (3) over the gas lift (4) and rest it on the base (2).
E. Tighten the arms (6A & 6B) onto the bottom of seat cushion (7) by using 1”screws (12) and tighten the screws.
F. Attach the seat plate (5) to the bottom of the seat cushion (7) (with front of seat plate facing front of seat cushion) by
using 7/8" screws (11) and tighten screws.
G. Align back cushion (8) with seat cushion (7) by inserting back support plate (9) into the rear hole of the seat plate (5)
as shown in Diagram 1 and tighten by using 5/8”screws (10).
H. Place the assembled chair on top of gas lift (4) and press down until fully engaged.
I. Periodically (every 90 days) tighten all screws in the chair.
ATTENTION: Make certain all screws are fully tightened before using chair.
Part #
Description
Quantity
1.
2.
3.
4.
5.
6A.
6B.
7.
8.
9.
10.
11.
12.
13.
Casters
5 Star Base
Telescoping Cover
Gas Lift
Seat Plate
Left Arm
Right Arm
Seat Cushion
Back Cushion
Back Support Plate (already
attached to the back cushion
5/8”Screws
7/8”Screws
1”Screws
Wrenches
5
1
1
1
1
1
1
1
1
1
2
4
6
2
A S S E M B L Y I N S T R U C T I O N S
P A R T S L I S T