Trust ICS-2000 User manual

ICS-2000
OCTOPUS CONTROL STATION
USER MANUAL
Item 71110 Version 1.0
Visit www.trust.com
for the latest instructions

ICS-2000 OCTOPUS CONTROL STATION
5
COMPATIBILITY
This product works with all Trust Smart Home
transmitters and receivers.
FUNCTIONALITY
The ideal solution to wirelessly control and monitor
your home for ultimate comfort and security
WIRELESS RADIO SIGNAL
• The 433.92 MHz radio signal passes through walls, windows and doors.
• Indoor 433.92 MHz range: up to 30 m. Outdoor 433.92 MHz range: up to 70 m (optimal conditions).
• The 868 MHz radio signal passes through walls, windows and doors.
• Indoor 868 MHz range: up to 70 m. Outdoor 868 MHz range: up to 120 m (optimal conditions).
• The Zigbee radio signal passes through walls, windows and doors.
• Indoor Zigbee range: up to 30 m. Outdoor Zigbee range: up to 70 m (optimal conditions).
• The range is dependent on local conditions, such as the presence of metals. For example, the thin
metal coating in Low-emissivity (Low-E) glass can have a negative impact on the range of radio
signals.
• There may be restrictions on the use of this device outside the EU. If applicable, check whether this
device complies with local directives.
• This class 1 wireless device meets the essential requirements and other relevant conditions of
R&TTE Directive 1999/5/EC. Be careful when using wireless devices if you have a pacemaker or are
dependent on other life-saving, sensitive electronic equipment, because this device transmits radio
signals.
Read the manual carefully. Failure to follow these instructions can be dangerous.
Incorrect installation will void any warranty on this product.
For safety & liability information visit www.trust.com/safety

ICS-2000 OCTOPUS CONTROL STATION
6
LIFE SUPPORT
Never use Trust Smarthome products for life
support systems or other applications where
failures can have life-threatening consequences.
REPAIRS
Do not try to repair this product yourself.
The device contains no serviceable parts for the
user.
WATER-RESISTANT
This product is not water-resistant.
CLEANING
Clean this product with a dry cloth.
Do not use harsh chemicals, cleaning solvents or
strong detergents.
HANDLING
Do not drop the device, bump the device
against something or shake it. Rough handling
can damage internal circuit boards and fine
mechanics.
ENVIRONMENT
The product should not be exposed to extreme
heat or cold. This can damage the circuit boards
and batteries or shorten its life.

ICS-2000 OCTOPUS CONTROL STATION
7
1. Package content
First, please check if the package contains the following items:
AInternet control station
BRJ-45 cable/Network cable
CP1 cable (Used for smart meters with a P1 connection. See trust.com/71110 for more info)
DPower adapter
EUser manual
1
P1
Octopus Control station
P1
A
B
C
D
E

ICS-2000 OCTOPUS CONTROL STATION
8
This is a quick installation guide with basic installation and usage instructions.
Check the advanced manual on www.trust.com/71110 for more in-depth information like:
• Adding & using timers, scenes and rules
• Connecting & Controlling other devices
• Technical specifications
• App settings
• and more

ICS-2000 OCTOPUS CONTROL STATION
9
2. Connection ports
The control station has the following ports:
AMicro USB Power port. Used for connecting the control station to a wall socket
BNetwork port. Used for connecting to your home LAN network.
CP1 port. Used for smart energy meters with a P1 connection. See trust.com/71110 for more info
DUSB ports. Used for future connectivity extensions. See trust.com/71110 for more info
P1
2
A
B
C
D

ICS-2000 OCTOPUS CONTROL STATION
10
3. Connect the control station to your modem/router
Connect the control station to the modem/router using the included RJ-45/network cable.
P1
4321
3

ICS-2000 OCTOPUS CONTROL STATION
11
4. Connect the power adapter
Connect the micro usb power adapter to the Octopus control station and insert the plug of the
power adapter into a wall socket. The LEDs of the control station will light up and start to spin to
update the firmware.
Do not disconnect the power or interrupt the control station in any way when the LED
ring is spinning green to update the firmware. When the control station is done booting and
updating all four LEDs will stay green. This can take a few minutes.
P1
4321
4

ICS-2000 OCTOPUS CONTROL STATION
12
5. Check installation
5a. If the installation of the control station is successful, all four LEDS (in the ring) will light up green
and stay green. Check the advanced manual on how to disable the LED light.
5b. If after installation a red LED lights up try to take the following steps:
1. Check if network cable is connected to the modem/router and control station
2. Check if power adapter is connected to the wall socket and the control station
3. Press the network cable and power cable firmly into the control station and modem/router.
4. Connect the control station directly to your modem.
5. Disconnect and reconnect the power adapter.
For more troubleshooting go to trust.com/71110
5a 5b

ICS-2000 OCTOPUS CONTROL STATION
13
6. Mounting (Optional)
6a. Secure the included screw in the surface where the control station will be mounted. Make
sure the screw is not placed in a crack or a hole in the surface.
6b. Place the control station on the screw.
6a 6b

ICS-2000 OCTOPUS CONTROL STATION
14
Make sure the screw is fastened in a way that the rubber feet of the control station are firmly
pressed against the surface when placed on the screw.
6c. For best performance mount the control station with the cables facing down.
6c

ICS-2000 OCTOPUS CONTROL STATION
15
8a 8b
8a. Android
Open the Play Store, search for the Trust Smart
Home app and install the app on your mobile
device.
8b. iOS
Open the App store, search for the Trust Smart
Home app and install the app on your mobile
device.
8. Install the app

ICS-2000 OCTOPUS CONTROL STATION
16
9
Make sure your phone/tablet is connected to
the same Home/LAN network as your ICS-2000.
When opening the App after installation the login
screen will be shown.
AFirst press on the picture of the ICS-2000 control
station
BPress the CREATE ACCOUNT button.
CA screen appears to fill in your account
information. Fill in your name, email address and
a self created password.
DChoose if you want to receive a newsletter or
not. (The newsletter contains information about
updates for the control station)
EWhen all information is filled in press the NEXT
button to continue the registration.
9. Register account
A
B
C
D
E

ICS-2000 OCTOPUS CONTROL STATION
17
The App will scan for any control station connected
to the network.
AWhen your control station is installed properly
the App will show a message that the Octopus
Control station is found.
BPress NEXT to continue the linking process.
CThe App is now connecting with your control
station.
If you see above message, press the MANUAL
button and fill in or select the correct MAC
address. The MAC address can be found on
the bottom of the control station. For more
information on manual registration check the
advanced manual on trust.com/71110
If the App cannot connect to the control
station go to trust.com/71110 for troubleshooting
and support.
10. Link control station automatically “Manual linking required”
C
B
A
MAC: 00-00-A2-00-12-11

ICS-2000 OCTOPUS CONTROL STATION
18
DAfter successful connection, a dialogue is
shown to press the the blue circling button on
your control station.
EPress the blue circling button on your control
station within 60 seconds to link your control
station to your account.
P1
E
D

ICS-2000 OCTOPUS CONTROL STATION
19
11. Add a room
FWhen the registration process is completed the
home screen of the App will be shown with the
message “Successfully Linked”.
APress the + button at the top of the screen to
add a new room
F
A

ICS-2000 OCTOPUS CONTROL STATION
20
BEnter the name of the room you want to add.
CPress ADD
DThe added room is now listed in your home
B
C
D

ICS-2000 OCTOPUS CONTROL STATION
21
12. Add a device
APress on a room name to open it. BPress the + button at the top of the screen to
add a new device.
A
B

ICS-2000 OCTOPUS CONTROL STATION
22
CEnter a name for the device you want to add
DPress ADD.
ESelect the type of device you want to add to
your room.
C
D
E

ICS-2000 OCTOPUS CONTROL STATION
23
13. Connect a new device
If you already control your Trust Smart Home
receiver with a remote control or wall switch
continue to step 14. (Only for Startline products)
APut your receiver in connect/learn mode. (Read
the manual of the receiver on how to put it in
connect/learn mode).
BWhen the receiver is in connect/learn mode
press CONNECT.
The receiver will go on and o twice to
acknowledge the connection.
CThe device is now added to your room. You
can now control the device with the App.
DUse the buttons to control the device.
1 sec.
A
A
B
CD