TruVision TVW-DVM User manual

TruVision
Wedge Dome
Back Box and Dual View
Mount Installation Guide
P/N 1073093-EN • REV C • ISS 28JUL21

© 2021 Carrier. All rights reserved. Specifications subject to change
without prior notice.
TruVision names and logos are a product brand of Aritech, a part of
Carrier.
Contact information
EMEA: https://firesecurityproducts.com
Australian/New Zealand: https://firesecurityproducts.com.au/
Product documentation
Please consult the following web link to retrieve the electronic version
of the product documentation. The manuals are available in several
languages.

Installation Guide 1
Content
Product overview 2
Product and package contents 2
TVW-DVM dual view mount 2
TVW-AWB-1 outdoor angled back box 5
TVW-AWB-2 indoor angled back box 7
TVW-2G-AD adapter plate 9
Installation 11
Specifications 23
TruVision wedge camera bracket and mount 23

2 Installation Guide
Product overview
This is the installation guide for the following TruVision wedge
camera models:
TVW-DVM (dual view mount) (use with TVD-PPB)
TVW-AWB-1 (angled back box for outdoor application)
TVW-AWB-2 (angled back box for indoor application)
TVW-2G-AD (adapter plate for wedge camera with 2-gang
box)
Product and package contents
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use the
unit; contact the supplier immediately. If the unit is returned, it
must be shipped back in its original packaging.
TVW-DVM dual view mount
The TVW-DVM dual view mount (purchased separately) allows
you to install two panoramic cameras on a single mount. You
then obtain a view of the surrounding area without requiring a
complex integration effort when connecting to your storage
device or video management system (VMS).

Installation Guide 3
Camera mount:
Tube adapter (30 x 12 mm): Conduit cover/plug:
Template A:
Template B:

4 Installation Guide
Screw 3 x 10 m (5 pcs m):
Screw (10 pcs):
Drywall anchor 7.5 x
24.5 mm
M4 screw 4 x 25 mm
Screw 3 x 8 mm (2 pcs): Screw 4 x 10 mm (5 pcs):

Installation Guide 5
Rubber ring:
Figure 1: Cameras attached using the dual view mount
TVW-AWB-1 outdoor angled back box
The TVW-AWB-1 outdoor angled back box (purchased
separately) is weather resistant and includes a G1 threaded
conduit access and plug. It conceals the interconnect cables
and eliminates the blind area below the camera when the
camera is installed on a wall.

6 Installation Guide
Camera back box:
Tube adapter (30 x 12 mm): Conduit cover/plug:
Template A:
Rubber ring:

Installation Guide 7
Screw (5 pcs):
Drywall anchor 7.5 x 24.5 mm
M4 screw 4 x 25mm
Screw 3 x 10 mm
(5 pcs):
Screw 3 x 8 mm (2 pcs): Screw 4 x 10 mm
(3 pcs):
Figure 2: Camera mounted on an outdoor back box
TVW-AWB-2 indoor angled back box
The TVW-AWB-2 indoor angled back box (purchased
separately) conceals the interconnected cables and eliminates
the blind area below the camera when the camera is installed
on a wall.

8 Installation Guide
Camera back box:
Template B:
Screw 5 pcs:
Drywall anchor (7.5 x
24.5 mm)
M4 screw (4 x 25 mm)
Screw 3 pcs (4 x
10 mm):

Installation Guide 9
Figure 3: Camera mounted on an indoor back box
TVW-2G-AD adapter plate
The TVW-2G-AD adapter plate (purchased separately) allows
you to attach the panoramic wedge camera to a standard 4-inch
2 gang box.
Camera adapter plate:

10 Installation Guide
Template A:
Rubber ring:
Screw 5 pcs:
Drywall anchor (7.5 x 24.5 mm)
M4 screw (4 x 25 mm)
Screw 3 x 8 mm (2 pcs):
Screw 4 x 10 mm (3 pcs):

Installation Guide 11
Figure 4: Wedge camera attached to a 2-gang box
Installation
To mount two wedge cameras on a dual view mount:
1. Attach the TVW-DVM dual view mount to an installed
pendant mount tube. An adapter is included in the kit that,
if required, can be used to match-up with the threading
(G1 male or G1 female) of the pendant mount tube.

12 Installation Guide
2. Loosen the screws with the tamper-resistant hex wrench
(supplied) to remove the camera cover.
3. Pull the cables through the bracket tube and to both back
boxes, conect the cables to cameras and place the
connecters and cables into the back boxes.

Installation Guide 13
4. Mount the two cameras on both sides of the TVW-DVM
dual view mount.

14 Installation Guide
5. Re-attach the camera covers to the cameras.
To mount the wedge camera on an outdoor angled
back box:
1. Drill the holes for the mounting hardware in the mounting
surface using the supplied drill template.
2. Detach the TVW-2G-AD adaptor plate from the back box.

Installation Guide 15
3. Mount the TVW-2G-AD adaptor plate to the mounting
surface using the supplied hardware.
4. Mount the outdoor angled back box to the TVW-2G-AD
adaptor plate using the supplied hardware.
5. Loosen the screws with the tamper-resistant hex wrench
(supplied) to remove the camera cover.

16 Installation Guide
6. Connect the cables, conceal the cables and connectors
inside the back box and mount the camera base to the
outdoor angled back box.
7. Re-attach the dome cover to the camera.

Installation Guide 17
To mount the wedge camera on an indoor angled back
box:
1. Drill the holes for the mounting hardware in the mounting
surface using the supplied drill template.
2. Mount the indoor back box to the mounting surface by
using the supplied hardware.

18 Installation Guide
3. Loosen the screws with the tamper-resistant hex wrench
(supplied) to remove the camera cover.