TruVision TVD-CB3 Cup Base User manual

P/N 1073419-EN • REV E • ISS 05JUL21 1
TruVision TVD-CB3 Cup Base
Installation Instructions
Dimensions
Dimensions:
Weight: 335 g (0.73 lb.)
Accessories:
Screw A: 3 pcs.
Used to install the camera adapter plate to the cup base.

2 P/N 1073419-EN • REV E • ISS 05JUL21
Supported devices
•TVD-5301
•TVD-5302
•TVD-5303
•TVD-5304
•TVD-5403
•TVD-5501
•TVD-5502
•TVD-5601
•TVD-5602
•TVD-5603
•TVT-5301
•TVT-5302
•TVT-5303
•TVT-5304
•TVT-5305
•TVT-5306
•TVT-5307
•TVT-5501
•TVT-5502
•TVT-5601
•TVT-5602
•TVT-5603
•TVT-5604
•TVT-5605
•TVT-5606
•TVT-5607
•TVD-5305
•TVD-5306
•TVD-5401
•TVD-5402
•TVT-5608
•TVT-5609
•TVT-5610
•TVT-5611
•TVD-
2202/4202
•TVD-
2401/4401
•TVD-
2402/4402
•TVD-
2403/4403
•TVD-
2404/4404
•TVD-
2405/4405
•TVD-
2406/4406
•TVT-
2401/4401
•TVT-
2402/4402
•TVT-
2403/4403
•TVT-
2404/4404
•TVD-SNB
Swan Neck
Wall Mount
•TVD-PPB
Pendant
Mount
•TVD-CBW
Wall Mount
Installing a TVD-CB3 cup base to a dome
camera
It is a similar process for a turret camera. Refer to the turret camera
installation guide for details. When assembling a TVD-CB3 to a dome
camera, you require:
•TVD-CB3 cup base
•Adapter plate. Included with dome or turret camera.

P/N 1073419-EN • REV E • ISS 05JUL21 3
Please refer to the camera mounts guide to verify if an adapter plate
is needed and included with your camera.
•Adapter plate mounting screws
To mount a dome camera to a TVD-SNB wall mount with a TVD-CB3
cup base:
1. Route the camera cables through the wall mount. Attach the swan
neck mount to the wall using the expansion anchors that are
provided with the swan neck mount.
2. Screw the cup base onto the swan neck mount and tighten with the
locking screw, as shown below (A). Then attach the camera adapter
plate to the cup base (B) using screw A.
Note: The mounting plate is shipped with the camera. The image
may not match the actual plate supplied. The included plate varies
depending on the camera.

4 P/N 1073419-EN • REV E • ISS 05JUL21
3. Loosen the screws on the bubble assembly using the Torx wrench
that is supplied with the camera. Remove the bubble assembly and
liner from the dome module.
4. Connect the cables to the dome camera.
5. Attach the dome assembly of the camera (A) to the camera adapter
plate, using the screws provided with the camera. Then reattach the
dome liner (B).

P/N 1073419-EN • REV E • ISS 05JUL21 5
6. Reattach the bubble assembly to the camera.
To mount a dome camera to a TVD-PPB pendant bracket with a TVD-
CB3 cup base:
It is a similar process for a turret camera. Refer to the turret camera
installation guide for details.

6 P/N 1073419-EN • REV E • ISS 05JUL21
1. Screw the pendant mounting plate onto the pendant mount tube
and tighten with the locking screw, as shown.
2. Route the camera interconnect cables through the pendant mount.
Attach the mount to the ceiling using the expansion anchors that
are included with the pendant mount.
3. Screw the cup base onto the pendant mount and tighten with the
locking screw. Using the adapter plate mounting screws, attach the
camera mounting plate to the cup base.
Note: The camera mounting plate is shipped with the dome
camera. The image below may not match the actual plate supplied.
The included plate varies depending on the camera.

P/N 1073419-EN • REV E • ISS 05JUL21 7
4. Loosen the screws on the dome assembly (1) using the using the
Torx wrench that is supplied with the camera and remove the dome
bubble assembly and liner (2).
5. Connect the cables to the dome camera.
6. Using screws that are supplied with the camera, attach the dome
assembly to the mounting plate.

8 P/N 1073419-EN • REV E • ISS 05JUL21
7. Reattach the dome liner and bubble assembly to the camera.

P/N 1073419-EN • REV E • ISS 05JUL21 9
Installing a TVD-CB3 cup base to a turret
camera
It is a similar process for a dome camera.
To mount a turret camera to a TVD-CBW wall mount with a TVD-CB3
cup base:
1. Route the camera cables through the wall mount. Attach the wall
mount to the wall using the expansion anchors that are provided
with the TVD-CBW.
2. Screw the cup base onto the wall mount and tighten with the locking
screw, as shown below (A). Attach the camera adapter plate to the
cup base (B) using screw A, routing the camera cables through the
adapter plate.

10 P/N 1073419-EN • REV E • ISS 05JUL21
3. Rotate the trim ring counterclockwise to remove it from the camera.
Attach the camera base to the adapter plate using the screws
provided with the camera.
4. Connect the cables from the camera to the cables routed through
the wall mount.
5. Reattach the camera to the camera base. Then, attach the trim ring
to the camera and rotate it clockwise to secure it.

P/N 1073419-EN • REV E • ISS 05JUL21 11
Legal information
Copyright
© 2021 Carrier. All rights reserved. Specifications
subject to change without prior notice.
Trademarks and
patents
TruVision names and logos are a product brand of
Aritech, a part of Carrier.
Certification
Contact
information
EMEA: https://firesecurityproducts.com
Australian/New Zealand:
https://firesecurityproducts.com.au/

12 P/N 1073419-EN • REV E • ISS 05JUL21
Product
documentation
Please consult the following web link to retrieve the
electronic version of the product documentation. The
manuals are available in several languages.