TSM SD-71 Instruction manual

Page 1 of 2
Technical Data
Revised October 2008
SD-71
Automatic Liquid Soap Dispenser
Surface Mounted
Since 1966
Tubular Specialties Manufacturing, Inc.
13011 South Spring Street, Los Angeles, CA 90061-1685
Phone 800/CALL TSM (800/225-5876) or 310/515-4801
www.GrabBar.com • Fax [phone]
Mounting Holes (4)
Surface Mounted Automatic Liquid Soap Dispenser shall hold
and dispense up to 800 ml (27 ounces) of liquid and lotion
soaps, synthetic detergents and antibacterial soaps containing
PCMX and/or Triclosan with a viscosity range of between 5 and
3500 mPa-s or cP (MilliPascal-sec or Centipoise). Dispenser body
shall be molded of high-impact white plastic. Dispenser shall be
powered by either one (1) 9 V or six (6) AA-size (1.5 V) batteries
(not supplied) and shall operate automatically from IR sensor
that shall activate soap dispensing when hands are placed in
sensor zone. Sensor detection range shall be adjustable by
Specification
owner. Dispenser shall have two (2) soap dosage settings and shall
pump either of two preset ranges of .02 + .01 fluid ounces or .04
+ .01 fluid ounces (.5 ml to .7 ml or 1 ml to 1.4 ml) of soap during
each activation. A tamper-resistant soap level viewing winder shall
be provided. Unit shall have a swing open body secured with side-
mounted lock that is opened with special key provided.
Surface Mounted Automatic Liquid Soap Dispenser shall be model
SD-71 as manufactured by Tubular Specialties Manufacturing,
13011 South Spring Street, Los Angeles, California 90061,
tel 800-Grab Bar.
© 2008, Tubular Specialties Mfg., Inc. All Rights Reserved
Manufacturer reserves the right to alter design or dimensions without formal notice and without incurring obligation.
✔Guarantee
TSM SD-71 Automatic Liquid Soap
Dispenser is guaranteed against
defects in workmanship and material
for one year from shipping date.
Soap Level
Viewing
Window
Operational
LED Indicator
Soap
Dispensing
Nozzle
Lock
Key
4
5/8”
(118mm)
S S
1
3/64”
(27mm)
S
S
C
10
5/16”
(263mm)
3
5/8”
(92mm)
4
7/16”
(113mm) 2
3/32”
(53mm)
5
5/16”
(135mm)
4
5/8”
(117mm)

Tubular Specialties Manufacturing, Inc.
13011 South Spring Street, Los Angeles, CA 90061-1685
Phone 800/CALL TSM (800/225-5876) or 310/515-4801
online www.grabbar.com • Fax [phone]
Installation
Install unit on wall surface at locations marked by an “S”.1.
The recommended installation height for general utility is2.
42” to 46” (1067 - 1168mm) above finished floor and 10”
(254mm) minimum above washbasin or countertop. A mounting
template is provided.
It is the installer’s responsibility to select fasteners that are3.
appropriate for the wall condition and application; TSM does
not include fasteners.
All accessories must be checked frequently to ensure that4.
the installation is secure and the product is in good working
condition.
Tech Data, page 2 of 2
Automatic Liquid Soap Dispenser
SD-71
© 2008, Tubular Specialties Mfg., Inc. All Rights Reserved
Manufacturer reserves the right to alter design or dimensions
without formal notice and without incurring obligation.
Guarantee
TSM SD-71 Automatic Soap Dispenser
is guaranteed against defects in
workmanship and material for one year
from shipping date.
4
Operation
Soap is automatically dispensed when hands are placed in
sensor zone. Owner sets soap dosage range manually inside
housing. Unit is reloaded by unlocking lock with special key
(supplied), swinging open dispenser body and removing and
refilling internal soap container. Soap dispenser will continue to feed
properly until empty. Tank supply is replenished manually on cycle
determined by maintenance needs. A complete instruction manual is
provided with each unit.