Curtis TCN Series Datasheet

Service & Sales
1-800-421-6150 www.wilburcurtis.com
OPTIONAL
FAUCET
INSTRUCTIONS AND PARTS LIST
TCN SERIES ICED TEA DISPENSERS
WARNING:
• Clean the dispenser completely before using it for the rst time according to the DAILY CLEANING
INSTRUCTIONS (back). Clean it regularly as instructed in the DAILY CLEANING INSTRUCTIONS.
• This product can expose you to chemicals including Acrylamide and Bisphenol A (BPA), which are known
to the State of California to cause cancer and birth defects or other reproductive harm. For more information
visit www.P65Warnings.ca.gov.
PARTS LIST
ITEM # PART # DESCRIPTION
1A WC-56052 LID, BREW ASSY THROUGH TCN
1B WC-56081 LID, LATCHABLE TCNL
1C WC-61436 LID, PLASTIC TCN (OLD)
2 WC-38471 LABEL, FRONT TCO ICED TEA GENERIC
3 WC-3276* LATCH, DRAW ZINC PLATED STEEL TCN200
4 WC-4263* NUT, 6-32 x ¼ OD HEX W/WASHER KEPS
5 WC-37260** KIT, FAUCET W/ADAPTER COMPLETE TC/TT
6A WC-1803 FAUCET, “SPB” SERIES,BLACK HANDLE/
PLASTIC 1-1/32-14 UNS CURT
6B WC-1865 FAUCET, “SPB” SERIES BLK PLST
SWEETENED/UNSWEETENED (NOT SHOWN)
ITEM # PART # DESCRIPTION
7 WC-1805 SEAT CUP, “S” FAUCET USE ON
WC-1800/B/LB/D/DL/L/WC-1803
8 WC-3289 HANDLE, GASKET TCN
9 WC-38163 LABEL, CURTIS LOGO WHITE TRANSFER
10 WC-5686 DRIP TRAY, OCTAGON STYLE
11 WC-3531 LEG, PLASTIC GLIDE TCN
12 WC-1840 FAUCET, PINCH TUBE TC
13 WC-1906 “C” RG .917 X .760 X .090 TT-3 TC’S
14 WC-1905 NUT, WING PLASTIC 1-1/32-14UNF (TC-2,3,5,10)
*Used on TCNL series only.
**For units manufactured before 03/01/2017.
1B
6A
6B 7
12
13
14
1C
1A
2
5
3
4
8
9
10
11

Wilbur Curtis Co., Inc.
Mail: 6913 Acco Street, Montebello, CA 90640-5403 U.S.A.
Phone: [phone] │ Fax: [phone] │ Technical Support Phone: [phone] (M-F 5:30 a.m.- 4:00 p.m. PST) │ Email: [email protected] │ www.wilburcurtis.com
05/2020 F-3639 revM
NOTICE - Do not use cleaning liquids, compounds or powders containing chlorine (bleach) or corrosives.
These products promote corrosion and will damage the nishes. USE OF THESE PRODUCTS WILL VOID THE
WARRANTY.
DAILY CLEANING INSTRUCTIONS
The following cleaning process requires a mild solution
of dish-washing detergent and warm water, and One-Pro
Beverage Equipment Cleaner (Curtis PN WC-79001). Mix
the One-Pro cleaner at a ratio of 1 oz. (28 g.) per 5 gal.
(19 L) of hot water (122°F/50°C min.).
Container
1 Prepare a mild solution of detergent and warm water.
Remove the container from the brewer and remove
the lid. Rinse.
2 Wash - Wipe the exterior surfaces with a sponge
and the detergent solution to remove spills and
debris. Use the detergent solution and a soft bristled
brush to wash the inside of the container.
3 Rinse - Rinse with clean, warm water.
4 Sanitize - Fill the container to the top with One-Pro
cleaning solution, mixed as specied above. Allow
the mixture to soak for 15 minutes, then drain. Fill
the container to the top with warm clean water, then
drain. Fill with water and drain a second time.
5 Disassemble the faucet - Unscrew the faucet
assembly from the container. Then, unscrew the
handle/bonnet assembly from the top of the faucet
and remove. Inspect the seat cup for wear. Replace
the seat cup if it is damaged.
6 Air Dry - Turn the container upside down and allow
to air dry.
Faucet Parts and Lid
7 Wash - Wash the lid and faucet parts with the
detergent solution.
8 Rinse - Thoroughly rinse all parts with clean, warm
water.
9 Sanitize - After rinsing, place the faucet parts in
One-Pro solution, mixed as specied above, and
allow them to soak for 15 minutes.
10 Air Dry - Remove the parts from the sanitizer, rinse
them off thoroughly, and allow them to air dry.
11 Reassemble - When dry, reassemble the handle/
bonnet. Hand tighten the handle/bonnet onto the
top of the faucet assembly. Hand-tighten the faucet
assembly onto the container outlet.
Seat cup
Faucet
Handle
Bonnet
WASH
RINSE
SANITIZE
To dis-assemble the top of
the faucet, grasp the bonnet
and push up on the seat cup,
while unhooking the handle.