Thank you for your selection of Tsubaki Belt Tension Meter T-ACE.
・ l Do not wet the product with water or oil nor give shock to it such as by dropping it. The product may fail.
・ l Do not disassemble or modify the product. Such a practice may cause fire or electric shock.
・ l Do not keep the product in places that are humid, hot or filled with dust.
・ l When the product will not be used, remove the battery and keep the product in the case.
・ l Do not bend the sensor microphone. To pull it out, hold the connector. Otherwise the product may fail.
!Danger Do not use the product when the belt is running. Otherwise, your hand may get caught.
(Measurement is possible only when the belt is at a stop.)
● PX tooth
/m
Type Width
(㎜) MASS Type Width
(㎜) MASS Type Nominal
Width
Width
(㎜) MASS Type Nominal
Width
Width
(㎜) MASS Type Nominal
Width
Width
(㎜) MASS Type Width
(㎜) MASS Type Width
(㎜) MASS
4 0.006 40 0.304 3.2 3.2 0.004 200 50.8 0.818 3.2 3.2 0.005 3 0.005 10 0.038
6 0.008 60 0.456 4.8 4.8 0.006 300 76.2 1.227 4.8 4.8 0.007 5 0.008 15 0.057
10 0.014 80 0.608 6.4 6.4 0.008 400 101.6 1.636 6.4 6.4 0.009 7 0.011 25 0.095
6 0.013 100 0.760 9.5 9.5 0.012 500 127.0 2.045 10 0.015 50 0.190
10 0.022 120 0.912 12.7 12.7 0.016 025 6.4 0.015 5 0.016 25 0.170
15 0.034 031 7.9 0.019 10 0.032 50 0.340
10 0.041 6 0.015 025 6.4 0.017 025 6.4 0.012 037 9.5 0.023 15 0.048 75 0.510
15 0.062 10 0.025 031 7.9 0.021 031 7.9 0.015 050 12.7 0.034 20 0.064 50 0.550
25 0.103 15 0.038 037 9.5 0.026 037 9.5 0.018 075 19.1 0.052 25 0.080 75 0.825
15 0.084 10 0.038 050 12.7 0.035 100 25.4 0.068
25 0.139 15 0.058 050 12.7 0.048 050 12.7 0.042 037 9.5 0.036 15 0.075 5 0.012
40 0.223 25 0.096 075 19.1 0.073 075 19.1 0.062 050 12.7 0.046 20 0.100 10 0.024
60 0.334 100 25.4 0.097 100 25.4 0.083 075 19.1 0.069 25 0.125 15 0.036
40 0.393 15 0.088 075 19.1 0.101 075 19.1 0.084 100 25.4 0.091 50 0.250 20 0.047
60 0.589 25 0.148 100 25.4 0.135 100 25.4 0.112 150 38.1 0.146 75 0.375
80 0.786 40 0.237 150 38.1 0.202 150 38.1 0.169 200 50.8 0.194
100 0.982 60 0.355 200 50.8 0.269 200 50.8 0.225 050 12.7 0.068 25 0.180 15 0.079
120 1.178 300 76.2 0.404 300 76.2 0.337 075 19.1 0.096 50 0.360 20 0.106
15 0.076 40 0.417 200 50.8 0.635 100 25.4 0.127 75 0.540 25 0.132
25 0.127 60 0.626 300 76.2 0.953 150 38.1 0.191
40 0.203 80 0.835 400 101.6 1.270 200 50.8 0.254
60 0.304 100 1.043 300 76.2 0.380
120 1.252 400 101.6 0.538
Tsubaki Belt Tension Meter T-ACE calculates the tension
using the following formula: Model BDTM101
Measuring range 0.1～9999N , 30～600Hz
･Frequency ･Span length Belt span length 0.001～9.999m
Unit mass 0.001～9.999㎏/m
Working temperature －10～60℃
Power supply Dry cell (AAA) x 4 pieces
･Belt tension Mass and dimensions 160 g (main unit)
162 long x 61.6 wide x 30 thick in ㎜
Accessories Sensor microphone,
dry cells (AAA x 4 pieces), carrying cas
F: Frequency
T: Belt tension Dp: Large pulley pitch diameter
L: Span length dp: Small pulley pitch diameter
W: Belt unit mass c: Distance between shafts
※ Even if the mounting tension is adequate, the vibration frequency may be out of the
measurable range of the product depending on a combination of measuring conditions used.
(A particular attention is required when the span length exceeds 1 m.)
DT10
DH
LT10 DT5
DL
UP8M DP14M
XH H
T20
P14M DP8M H
T5
AT10
P5M
UP5M DP3M XL DXL AT20
P8M DP5M
L
T-ACE Instruction Manual
P2M
UP14M MXL XXH MXL T2.5 AT5
P3M
UP3M
XL
For Safe Use
List of Unit Mass
Basic formula
Specifications
Ｆ ＝ １
２Ｌ
Ｔ
ＷＬ ＝ (Ｄｐ－ｄｐ)
４
２
Ｃ －
２
Ｔ ＝ ４ × Ｗ × Ｌ × Ｆ
２２
