TT electronics S19P01 User manual

S-2CONNECT Sense
User Guide
© TT electronics plc Issue A 06/2020 Page 1
General Note
TT Electronics reserves the right to make changes in product specicaon without
noce or liability. All informaon is subject to TT Electronics’ own data and is
considered accurate at me of going to print.
TT Electronics Sweden AB
Gullfossgatan 3, 164 40, Kista, Stockholm, Sweden
www.electronics.com/iot
User Guide
S-2CONNECT Sense
S19P01

S-2CONNECT Sense
User Guide
© TT electronics plc Issue A 06/2020 Page 2
General Note
TT Electronics reserves the right to make changes in product specicaon without
noce or liability. All informaon is subject to TT Electronics’ own data and is
considered accurate at me of going to print.
TT Electronics Sweden AB
Gullfossgatan 3, 164 40, Kista, Stockholm, Sweden
www.electronics.com/iot
1 Contents
2
2.1
Introduction
Packet contents
3
3
3 Environmental information 3
4 Safety precautions and prohibited handling 4
5 General guidelines 5
6
6.1
6.2
6.3
6.4
6.5
6.6
Installation and usage
Install the battery
Mounting
Switching the device on
Using the Device
Battery Operation
LED Functionality
6
6
6
7
7
7
7
7 Operating and maintenance recommendations 7
8
8.1
8.1.1
8.1.2
8.2
Error handling, faults and repairing
Error handling
First action
No radio communication
Faults and repairing
8
8
8
8
8
9 Accessories and peripherals 8
10
10.1
10.2
Technical parameters
Technical data
Radio frequencies
9
9
9
11
11.1
11.2
11.3
11.3.1
11.3.1.1
11.3.1.2
Compliances
Declaration of Conformity
FCC Compliance
Approved module
Telit BlueMod+S42
FCC Labelling
Bluetooth Qualification
10
10
10
10
10
10
10

© TT electronics plc Issue A 06/2020 Page 3
General Note
TT Electronics reserves the right to make changes in product specicaon without
noce or liability. All informaon is subject to TT Electronics’ own data and is
considered accurate at me of going to print.
TT Electronics Sweden AB
Gullfossgatan 3, 164 40, Kista, Stockholm, Sweden
www.electronics.com/iot
S-2CONNECT Sense
User Guide
2 Introduction
Thank you for choosing a TT Electronics product. Please read the user guide before bringing this device into service.
2.1 Packet Contents
1. S-2CONNECT Sense
2. Battery Hatch Key
3. Quick Start Guide
3 Environmental information
REACH
TT Electronics complies with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals regulatory
framework). Read more at www.s-2connect.com
This symbol on the device or the package means that all electronic and electrical equipment should
not be mixed with general household waste. The disposal of the device after it’s lifecycle could harm
the environment. Do not dispose the unit (or batteries) as unsorted municipal waste; it should be tak-
en to a specialised company for recycling. This device should be returned to your distributor or to a
local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Please go to www.s-2connect.com for more information.

© TT electronics plc Issue A 06/2020 Page 4
General Note
TT Electronics reserves the right to make changes in product specicaon without
noce or liability. All informaon is subject to TT Electronics’ own data and is
considered accurate at me of going to print.
TT Electronics Sweden AB
Gullfossgatan 3, 164 40, Kista, Stockholm, Sweden
www.electronics.com/iot
S-2CONNECT Sense
User Guide
4 Safety Precautions and Prohibited Handling
DO NOT ATTEMPT TO INSTALL, USE OR MAINTAIN THE S-2CONNECT Sense UNITL YOU HAVE READ
AND FULLY UNDERSTOOD THESE INSTRUCTIONS. BE SURE THIS INFORMATION REACHES THE OPER-
ATOR AND STAYS WITH THE PRODUCT AFTER INSTALLATION. DO NOT PERMIT UNTRAINED PER-
SONS TO INSTALL, USE OR MAINTAIN THIS PRODUCT.
Inspect the device for physical damage and contamination. Do not connect the device, or accessory if
you detect oil, grease, water, broken or damaged parts.
When unpacking the device, make sure to handle it with care. Rough handling may shock the device,
causing damage. Check that the device is free from cracks, fractures, leakage.
Do not place the device near any other device that may cause sparks (such as a switch or a fuse). The
battery may generate flammable gas when charged, so always ensure the battery is kept away from
open fire and/or flames to prevent sparks from igniting or causing explosions.
Do not allow the device to be immersed in water/sea-water.
Do not attempt to disassemble or destroy the unit. The product must be handed over to an authorized
workshop for maintenance and to a suitable recycling station when it is taken out of service.
Use this product only within specified temperatures.
Do not place other products or objects on top of S-2CONNECT Sense or the performance of the device
internal antennas may be compromised.
This product contains a battery. The battery is replaceable.
Pay special attention to the battery if the product is taken out of use, and if the product is up for dis-
posal. Dispose used batteries as hazardous waste.

© TT electronics plc Issue A 06/2020 Page 5
General Note
TT Electronics reserves the right to make changes in product specicaon without
noce or liability. All informaon is subject to TT Electronics’ own data and is
considered accurate at me of going to print.
TT Electronics Sweden AB
Gullfossgatan 3, 164 40, Kista, Stockholm, Sweden
www.electronics.com/iot
S-2CONNECT Sense
User Guide
5 General Guidelines
Familiarise yourself with the functions of the device before using it.
All modifications of the device are forbidden for safety reasons. Damage caused by user modifica-
tions to the device is not covered by warranty.
Only use the device for its intended purpose. Using the device in an unauthorised way will void the
warranty.
Damage caused by disregard of guidelines in this manual is not covered by the warranty and the
dealer will not accept responsibility for any ensuing defects or problems.
TT Electronics, nor its authorised resellers can be held responsible for any damage (extraordinary,
incidental or indirect) –of any nature (financial, physical….) arising from possession, use or failure of
this product.
Due to constant product improvements, the actual product appearance might differ from the shown
images.

© TT electronics plc Issue A 06/2020 Page 6
General Note
TT Electronics reserves the right to make changes in product specicaon without
noce or liability. All informaon is subject to TT Electronics’ own data and is
considered accurate at me of going to print.
TT Electronics Sweden AB
Gullfossgatan 3, 164 40, Kista, Stockholm, Sweden
www.electronics.com/iot
S-2CONNECT Sense
User Guide
6 Installation and usage
1. Make sure there is no damage to the equipment.
2. Choose your suitable installation location. Consider the environmental
requirements and be advised that this device contains antennas that could
be affected from other equipment within close range.
3. Remove the battery isolation tab. See below for instructions.
4. Check the LEDs to verify proper operation.
6.1 Activating and replacing the battery
6.2 Mounting
This product can be mounted on any type of surface with standard screws (not included in the package). It can be mounted
in any desirable direction except that the device should not be mounted with the battery hatch upwards if there is any risk
for water or other fluids pouring over the device. The device can be used as a portable device and does not require fixed
installation.
If the product is mounted on metallic surface or close to substantial amount of metal the antenna performances may be-
come compromised. For full functioning antenna performance, the device should be mounted not less than 30mm from
metal.
Avoid placing the unit close to powerful electromagnetic equipment.
1. Use the battery
hatch key provided
to open or close
the battery hatch.
2. To activate the
battery, lift the
battery hatch and
remove the battery
isolation tab.
3. When replacing
the battery, pay
attention to the
plus and minus
indicators.
4. Close the battery
hatch carefully
using the battery
hatch key. Ensure
the hatch is aligned
with the indicator
as shown.

© TT electronics plc Issue A 06/2020 Page 7
General Note
TT Electronics reserves the right to make changes in product specicaon without
noce or liability. All informaon is subject to TT Electronics’ own data and is
considered accurate at me of going to print.
TT Electronics Sweden AB
Gullfossgatan 3, 164 40, Kista, Stockholm, Sweden
www.electronics.com/iot
S-2CONNECT Sense
User Guide
6.3 Switching the Device on
This device switches on automatically following insertion of the battery.
6.4 Using the Device
This device is intended for restrict remote operation. Log in to your user interface to interact with the device.
6.5 Battery Operation
The battery operation time is depending on configuration, surrounding temperature and other parameters. It can be up to
12 months.
6.6 LED Functionality
S-2CONNECT Sense is equipped with a LED, that operates as:
• Long Blink at battery insertion
• Short Blink when communicating with S-2CONNECT Hub
7 Operating and Maintenance Recommendations
Ensure the device is operated within the correct operating temperatures.
This product requires no maintenance. It can be wiped clean with a damp cloth.

© TT electronics plc Issue A 06/2020 Page 8
General Note
TT Electronics reserves the right to make changes in product specicaon without
noce or liability. All informaon is subject to TT Electronics’ own data and is
considered accurate at me of going to print.
TT Electronics Sweden AB
Gullfossgatan 3, 164 40, Kista, Stockholm, Sweden
www.electronics.com/iot
S-2CONNECT Sense
User Guide
8 Error Handling, Faults and Repairing
8.1 Error Handling
8.1.1 First Action
If the device does not operate as expected the first step is always to check if the battery is fresh. Low battery LED
indication should indicate if the battery level is too low, but if you detect malfunction do always replace the battery
as the first step to get back to normal operation.
8.1.2 No Radio Communication
S-2CONNECT Sense use Bluetooth LE for communication with S-2CONNECT Hub. Check that S-2CONNECT Sense is
within radio communication distance from the S-2CONNECT Hub.
Other radio frequency devices may disturb the communication between S-2CONNECT Sense and S-2CONNECT Hub.
Try to move the units to another area if you suspect this might be the case.
8.2 Faults and Repairing
Faulty devices shall always be replaced. Do not try to repair the unit. The unit is sealed and cannot be opened without de-
stroying the device.
9 Accessories and Peripherals
S-2CONNECT Sense is part of a series of products including devices that can interoperate with S-2CONNECT Hub. Check the web-
site for more information www.s-2connect.com

© TT electronics plc Issue A 06/2020 Page 9
General Note
TT Electronics reserves the right to make changes in product specicaon without
noce or liability. All informaon is subject to TT Electronics’ own data and is
considered accurate at me of going to print.
TT Electronics Sweden AB
Gullfossgatan 3, 164 40, Kista, Stockholm, Sweden
www.electronics.com/iot
S-2CONNECT Sense
User Guide
10 Technical Parameters
10.1 Technical Data
10.2 Radio Frequencies
S-2CONNECT Sense—Dimensions and Weight
33.0 x 64.5 x 9.5 mm (L x W x H), Nominal weight 17g (excluding battery)
Battery type
CR2450
Housing
Polycarbonate
Operating Temperature
-20°C to + 85°C
Operating Humidity
0 –95 % RH, non-condensing
IP Rating
IP 65
Sensors Accuracy
*Only for devices with transparent hosing
Temperature -20°C to + 85°C (+/-0.3%)
Humidity 0 – 100 % RH (+/-2% RH)
Accelerometer +/-2g (+/-2mg/LSB)
Light sensor* Detects dark/light
Radio technology Frequency band
Bluetooth 2.4 GHz BLE

© TT electronics plc Issue A 06/2020 Page 10
General Note
TT Electronics reserves the right to make changes in product specicaon without
noce or liability. All informaon is subject to TT Electronics’ own data and is
considered accurate at me of going to print.
TT Electronics Sweden AB
Gullfossgatan 3, 164 40, Kista, Stockholm, Sweden
www.electronics.com/iot
S-2CONNECT Sense
User Guide
11 Compliances
11.1 Declaration of Conformity
Simplified EU Declaration of Conformity
TT Electronics hereby declares that S-2CONNECT Sense is in compliance with the essential requirements of the following
EU directives:
• RED 2014/53/EU
• RoHS 2011/65/EC
• WEEE 2012/19/EU
Full text of the conformity is available at www.s-2connect.com
This equipment complies with EU radiation exposure limits set fourth for an uncontrolled equipment. This equipment
should be installed and operated with minimum distance 20cm between the device and the user and/or any bystander.
11.2 FCC Compliance
S-2CONNECT Sense has been tested to fulfil the FCC requirements. Test reports are available upon request.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equip-
ment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communi-
cations. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at their own expense.
11.3 Approved Module
S-2CONNECT Sense includes a pre-approved radio module:
11.3.1 Telit BlueMod+S42
11.3.1.1 FCC Labelling
FCC ID: RFRMS42
IC: 4957A-MS42
11.3.1.2 Bluetooth Qualification
The BlueMod+S42 is a qualified design according to Bluetooth Qualification Program Reference
Document (PRD) V2.3.
Declaration ID: D032121
Qualified design : 88139
Radio Interface Manufacturer Type number
Bluetooth Telit BlueMod+S42