TTulpe B-10 N20 Eco User manual

TTulpe Indoor B-10 N20 Eco
TTulpe Indoor B-10 N20-E Eco
TTulpe Indoor B-10 N20/N25Eco
TTulpe Indoor B-10 B30/37/50 Eco
TTulpe Indoor B-10 P30/37/50 Eco
INSTALLATION, OPERATION AND MAINTENANCE MANUAL
148.00 mm
210.00 mm

The device is well built in accordance with the current legislation.
The CE sign positioned on the product indicates that it conforms to the following European Directives and Regulation:
• Regulation Gas Appliance (UE)2016/426
• European Standard:gas-fired instantaneous water heaters for the production of domestic hot water EN 26:2015
• Directive 2009/125/ECEco-design requirements for energy-related products
• Regulation (EU)2017/1369setting a framework for energy labelling
• Delegated regulation (EU)no.812/2013
• Delegated regulation (EU)no.814/2013
The appliance complies with the Regulation (EU) 2017/1369.
The energy label carries the information regarding the product's energy efficiency characteristics.
In this way the end consumer can identify and compare similar products and can make informed choices regarding high efficiency
appliances.
TTulpe Indoor B-10 Eco
M
A
62 dB
0 6
kWh/annum GJ/annum
2017 812/2013
PRODUCT DATASHEET
Indoor B-10 N20 Eco
Indoor B-10 N20-E Eco
Indoor B-10 N20/N25Eco
Indoor B-10 B30/37/50Eco
Indoor B-10 P30/37/50Eco
Declared load profile M
Indoor sound power level
dB(A)
62
Water heating energy efficiency class A
Water heating energy efficiency class %72
Annual fuel consumption GJ 6
Annual consumption of electrical energy kWh 0
A
TTulpe
2
148.00 mm
210.00 mm

3
When the product has reached the end of its serviceable life,
it shall be disposed of in an environmentally friendly way and
disposed of according to the regulations in force.
Separate collection and recycling of the product avoid
negative impact for environment and health,and allows
recovery of materials,to obtain energy and resources saving
Packing List:
1.gas instantaneous water heater 6.Screws and plastic plug
2.Instruction Manual 7.Rubber
3.Gas connector 8.Washer
4.Expansion screw 9.PTFE Tape
5.Stainless steel water hose
WARNING
This booklet contains information relevant to the user as
well as the installer.
The user must read the following chapters:General safety,
Flue gas device and Operation.
In parts of the manual the following symbols are used:
WARNING =for actions that require caution and
adequate preparation
PROHIBITED =for actions that MUST NOT be
performed
148.00 mm
210.00 mm
INDEX
GENERAL SAFETY WARNINGS
pag.
4
MAIN COMPONENTS pag. 5
TECHNICAL DATA pag. 6
INSTALLATION pag. 7
Regulations pag. 7
Wall mounting pag. 7
Room ventilation pag. 7
Electrical connection to battery pag. 7
Gas connection pag. 8
Water connection pag. 8
Disposal of waste product pag. 8
OPERATION pag. 8
Function pag. 9
Usage pag. 9
MAINTENANCE pag. 10
Troubleshooting:problems and solutions pag. 10
CERTIFICATE OF WARRANTY pag. 11

4
GENERAL SAFETY WARNINGS
The Operation Manual is an integral part of the product and so must
be carefully preserved to accompany the product; if it is lost or
damaged another copy can be requested from the Technical
Assistance Centre.
The installation of the device and any other repairs or maintenanc
e must be performed by qualified personnel according to the
law in force, in compliance with the installing regulations
including any revisions.
It is recommended that trained personnel install the device.
The device must be used according to the manufacturer
specifications. The manufacturer cannot be held
contractually or otherwise responsible for damage caused to
persons, anim als, or objects because of incorrect
installation, repair or mai ntenance or improper usage.
The product s’safety or automatic regulation devices must not
be modified unless performed by the manufacturer.
This device is intended for heating water and therefore must
be connected to a water distribution network who s’load,
and settings are compatible with the product.
If water spills, turn off the water supply and advise the
qualified personnel at the Technical Assistance Centre.
If the machine is not used for prolonged periods turn off the
gas supply.If there is a risk of the water freezing,empty the
water heater.
If the machine breaks down or does not function properly,
deactivate it, do not attempt to perform any repairs.
The machine s’maintenance must be performed at least once
a year: Book a maintenance session with the Technical
Assistance Centre ahead of time to save wasting time and
money afterwards.
When the product has reached the end of its serviceable life,
it shall be disposed of in an environmentally friendly way;
ensuring that the majority of the product is fully recycled in
compliance with the installing regulations including any
revisions.
When using the device, the following safety rules must be applied:
Do not use the machine for purposes other than those intend
ed by the manufacturer.
Do not block the intake and dissipation grills or the ventilation
openings in the area where the device is installed with rags,
paper,or any other materials.
If a gas leak is detected,do not switch on any electrical devic
es,telephones or any other objects that could produce a
spark.Ventilate the area by opening the doors and windows
and switch off the gas supply.
Do not place objects on top of the device.
Do not leave flammable containers or substances in the area
where the device is installed.
Do not attempt to repair the machine if it breaks down and/or
works incorrectly.
Children or inexperienced persons are prohibited from using
the device.
It is prohibited to open sealed elements. T
o maintain the proper functioning of the device:
-Periodically clean the devices exterior with soapy water,this im-
proves its appearance as well as preserving it from corrosion in
the long term.
-Do not use solvents,powders,or abrasive sponges.
-Do not clean the device and/orits parts with flammable materials
(e.g.petrol,alcohol,diesel etc.).
DESCRIPTION OF THE APPLIANCE
NOx identifies the group of the two most important nitrogen oxides:
-NO Nitrogen monoxide (not harmful to humans)
-NO2 Nitrogen dioxide (very harmful to humans and the
environment).
NOx is formed during combustion processes at high temperatures.
To reduce NOx emissions, it is necessary to cool the flame.
The water inside the water heater, after having been heated by
heat exchanger, gets in the burner, cools the flame, and gets out
to the final user.
The special burner cools the flame and check the airflow
necessary for the combustion, set up “cooled flames”avoiding the
loss of thermal efficiency, generating an optimal combustion with
low em issions.
Fig.1
148.00 mm
210.00 mm

MAIN COMPONENTS FIG.2
1 Thermostat of 85℃
2 Chimney
3 Thermostat of 77℃
4 Heat exchanger
5 Ignition pin
6 Burner
7 Connector of gas
8 Gas proportional valve
9 temperature probe
10 Battery box
11 Water flow sensor
12 Connector of water inlet
13 Back plate
14 Water inlet
15 Controller
Fig.2
5
148.00 mm
210.00 mm

6
Technical Data
Appliance name TTulpe gas fired water heater
Trade name
Type B11BS
Gas Category I2EK I2H I2E I3BP I3P
Model Indoor B-10
N20/N25Eco Indoor B-10 N20 Eco Indoor B-10 N20-E Eco Indoor B-10 B30/37/50Eco
Indoor B-10
P30/37/50Eco
Gas Type G20/G25.3 Natural Gas Natural Gas Butane/Propaneor
their mixtures Propane
Gas Pressure 20/25mbar 20 mbar 20 mbar 28-30/37/50mbar 30/37/50mbar
Countries of Destination NL
AT,BG,CH,CY,CZ,DK,
EE,ES,FI,GB,GR,HR,I
E,IT,LT,LU,LV,NO,
PT,RO,SE,SI,SK,TR
DE,PL,RO,LU
AT,BE,BG,CY,DE,
DK,EE,FI,FR,GB,GR,
HU,IT,LT,LU,LV,MT,
NL,NO,RO,SE,SI,
TR,PL
AT,CZ,DE,ES,FI,FR,
GB,GR,NL,IE,IT,PT,
RO,Sl,SK
Nozzles quantity 22
Nozzle diameter in mm 0.83&0.86 0.47&0.51 0.5&0.57
Nominal heat input
Qn kW 20
The nominal useful
output Pn kW 18.3
The Minimum heat
input Qm kW 7.5 6.5
The Minimum useful
output Pm kW 6.7 5.8
Nominal heat efficiency ＞84%
Gas Consumption m³/h2.11 0.618 0.818
NOxmg/kwh 36.31 21.25 54.79
Flue gas average
temperature 175
Hot water data
Nominal water flow rate 11L/min
Cold inlet water is 15℃,
water temperature of
maximum flame can reach
60℃
Cold inlet water is 15℃,
water temperature of
minimum flame can reach
35℃
Minimum water
Pressure Pw 0.1bar
Maximum water
Pressure Pw 10bar
Connectors'data
Water pipe connector G1/2”Inch
Gas pipe connector G1/2”Inch
Flue diameter Φ110mm
Flue length min./ max.0.5/3m
Battery Type LR20
Electrical voltage DC 1.5V
Dimension /Weight
Width x Heightx Depth 640x390x255mm
Weight 8.16kg
Country of Origin Made in P.R.C.
Manufacturer TTulpe B.V.
148.00 mm
210.00 mm

7
A.black
B.red
C.white
D.orange
E.blue
7.Temperature sensor
8.Water flow sensor
9.Controller Wires Ⅱ
10.Gas valve
11.lgnition pin
12.Controller
1.Thermostat of 77℃
2.Thermostat of 85℃
3.Controller Wires Ⅰ
4.Battery box
5.Wire of display
6.Temperature display
INSTALLATION
Regulations
The use of gas devices is controlled by precise regulations.
It is essential to observe all the regulations in force.
Installation of liquid petroleum gas (L.P.G) must comply with all the
distributor s’requirements and those of the regulations.
Wall mounting
Warning
Do not install this device in an area that contains dust, greasy
vapor and/orcorrosive elements.
- The device must be installed on a suitable wall surface in
proximity to a fume disposal flue
- It is vital to leave the minimal distances around the device as
shown in fig 3 to allow for maintenance operations to take place.
Location
The water heater must not be tightly placed in an enclosure or slot,
it should have an adequate flow of air around it
- The water heater must not be placed above a kitchen or other
cooking devices that might deposit grease vapor on its exterior
leading to corrosion
- Surfaces that sensitive to heat (e.g.wood)must be protected
using appropriate insulation.
- Fig.1 displays the dimensions necessary for wall mounting
Room ventilation
The installation of the water heater must comply with regulations in
force including any updates.
Warning: This device can only be installed in venues that are
permanently ventilated according to regulation in force.
Air circulation
It is vital that areas where gas devices are installed (type B) have
access to the amount of air necessary for the regular combustion of
gas as well as the ventilation of the venue.
- It is prohibited to use an extractor fan, fireplaces, and other
similar devices at the same time as the water heater
- The area where the water heater is installed must have a regular
flow of air for ventilation.
Air flow
The flow of air must occur by the following means:
- Permanent openings in the wall that lead outdoors
- Single or collective ventilation ducts.
The air used for ventilation must be taken directly from an outside
location,that is far from sources of pollution.
Indirect ventilation from adjacent areas are permitted with the fol-
lowing limitations:
-The adjacent area is equipped with direct ventilation
-The devices within the area to ventilate are connected to a waste
duct
-The adjacent area does not contain a bedroom and is not a com-
mon area;
-The adjacent area is not a fire hazard such as a storage area for
flammable materials,garage etc.
-The adjacent area is not lower than the area to ventilate as this
might lead to an opposing draught (this can be caused by other
devices that operate on the basis of combustion,a fireplace or
any suction device that have not been given an adequate air
supply)
-The air flow from the adjacent area occurs freely through permanen
topenings.
Electrical connection to battery
The device is powered by two 1.5 V batteries, alkaline long-lasting
model LR20, thus it is not necessary to connect the device to a
power socket.
Gas connection
Determine the pipe diameter according to current regulations.
Before installing the device blow in the gas pipe to eliminate any
residue from its manufacturing. Connect the water heater to the
inter nal system s’gas pipes and place a tap above the device for
the halting and release of gas.
The main gas supply pipe must be connected by a flat seat fitting
that allows the insertion of a gasket specifically provided for gas
connections.
Do not use a conical seat fittings or union conical with threading
sealed with hydraulic hackled hemp or Teflon.
The water heaters that are powered by tanks of L.P.G. gas with
regulation and interception devices, must be connected correctly
so to guarantee the safety of persons and the surrounding area.
Foll ow all related regulations.
50 50
200
Fig.3
Fig.4
Fig.5
148.00 mm
210.00 mm

8
When initially installing the device, qualified persons must
perform the following tests:
-Check that the internal and external parts of the gas supplying
device are sealed.
Check that the gas quantity supplied is equal to that required by
the device.
-
-
Check that the device receives the type of gas it is
manufactured to process.
Check that the gas supply pressure does not go beyond the
maximum pressure values displayed on the information plate.
- Check that the gas supply system supplies the necessary amoun
t of gas to the device and that it is equipped with all the
necessary safety devices prescribed by current regulations.
If the user is absent for a lengthy period, turn off the main gas
supply tap.
Do not obstruct the area s’ventilation openings where the device is
installed to avoid dangers such as the build-up of toxic and
explosive substances. Do not utilize gas tubes to earth electrical
devices. Water connection Connect the water heater to the
water supply and insert a tap to int ercept the water above the
device. From the front, the cold-water i nput is on the right and the
hot water output is on the left.
Insert the filter into the water valve input fitting.
Remove the plastic nut from the hot water output fit in before
connecting it to the water supply.
Check the water hardness (°f).
In case of high water hardness, we recommend
installing upstream of the appliance the water softener
device or oth er device in compliance with the regulations
including any re visions.
Ensure that the tubes of your water system are not used to
earth your electrical system or telephone, they are inappropriate
for p erforming this task.
In a short amount of time this can damage tubes and the device.
Disposal of waste product
This B11BS water heater is supplied with a device for releasing
flue gas.
For output of combustion by-products refer to the regulations in
force including any updates.
The gas devices with an attachment for a waste gas flue must be
connected directly to properly working chimney or flue pipe; only if
these devices are not present is it then permitted to release
gases directly outside.
The fitting of devices to a chimney or flue pipe must occur via a
smoke channel. Smoke channels must be connected to a
chimney or a smoke channel in the same or adjacent area to
where the device is installed and must be made of materials
resistant to mechanical strain, heat and the effects of combustion
by-product s and their condensation. The flue gas temperature
must always be above condensation temperature in all points of the
smoke chan nel regardless of external conditions.
FLUE GAS RELEASE SAFETY DEVICE
The product is equipped with a series of flue gas release safety
devices. The device ensures the correct release of combustion by -
products, the flow of combustible gas to the release conduit
and the smoke channel.
The safety device contains a “thermostat ,”it can stop the flow of
gas to the main burner and the pilot flame.
The safety device can be triggered by the partial or total obstruction
of the release conduit or the smoke channel.
Whenthe temperatureof thermostatresumeto normal,removethe fault
codeaccordingto the Fault Code Solution. Thenturnon the tap again.
If the device or its electrical connections breaks down, the product
cannot be put ON, it ensures a safe condition
If the device or its electrical connections breaks down, the machine
operation is blocked.
If the machine is constantly blocked because of the flue gas
safety device, it is necessary to request the assistance of a
qualified te chnician according
to law in force, to che
ck the correct releas
e of flue gas through
the release conduit
and/or the smoke ch
annel,ac-cording to
the installation regul
OPERATION
High water temperature
A-ON/OFFbutton
B-UP button
C-DOWN button
ation.
It is highly prohibited
to attempt to modify
or remove the flue g Fig.6
as safety device; thi
s risks the safety of
the user and persons in the area. Only a qualified technician who is
authorized by the manufacturer can meddle with the safety devic
e to check its functionality or to substitute it if necessary.
If it is necessary to replace the device, it is vital to only use “original
parts”supplied by the manufacturer since it has been designed,
studied, and regulated to be fitted with the water heater.
Fig.7Fig.8
Low water temperature
148.00 mm
210.00 mm

Function
The water heater is used to produce instant hot water. The
removal of hot water can be performed by multiple taps.
By turning on the relative tap, the main burner switches on heating
the water that passes.
1.After adjusting the temperature, the traditional knob control gas
water heater cannot keep the setting temperature constant due to
the fluctuation of water pressure and air pressure.
Due to its digital control valve and more advanced control system,
the controller can control the opening of the proportional valve ac
cording to the increase or decrease of the water temperature dete
cted by the temperature sensor , in case of water pressure or air
pressure fluctuation, so as to control the gas flow rate. Therefore,
the hot water outlet temperature can keep the setting
temperature constant.
2.The traditional knob control gas water heater will have high CO
rate under high pressure due to the unstable air pressure
supplied.
However, for this type of gas water heater with constant
temperature function, because the gas valve has a pressure
stabilizing fun ction, when the gas pressure is too high, the valve
will keep the pr essure at the outlet of the valve stable, then the
CO rate can be c ontrolled in a low range.
Usage
Ensure that the gas tap and all water taps are switched off
- Turn on the Main gas supply tap or that of the gas tank if using
Liquefied Petroleum Gas (L.P.G.)
- Open the gas tap,not supplied with the device,placed immediat
ely before the water heater on the gas input pipe
- Press ON/OFFbutton,the gas water heater will be in standby s
tatus.Press UP or DOWN button to set the temperature of wate
r outlet (Fig 7). Press UP or DOWN button for one time，then t
he setting temperature will increase or decrease 1℃accordingl
y.When long press UP or DOWN button for every 0.3 seconds,
the setting temperature will increase or decrease 1℃.Tempera
ture setting range can be 35-60℃
- When the gas water heater is connected with water supply,the
ignition pin will start to work and ignite the main burner.
- If disconnect the water supply (turn off the water tap)or press
ON/OFFbutton to turn off the gas water heater,the burner will
automatically shut down.Then the device awaits another heat
ing request.
If after 60 seconds it does not switch on, the controller detector
interrupts the flow of gas and blocks the device.
To reuse the device after it has been blocked, close the hot
water extraction tap and then reopen it to restart the sequence.
If the main burner accidentally switches off, the device will
attempt to turn it on again.
If within 60 seconds the device does not function it is blocked .
The device is built to function with normal water pressure; in add
ition, a temperature selector B is also supplied.
Rotate the knob completely to the left to obtain the minimum
water output or completely to the right for the maximum water
output.
When the water heater is not used for long periods close the
gas supply tap or the LPG gas valve on the tank.
For the best operational results, it is recommended to have
aqualified technician service the machine at least once a year.
DANGER OF FREEZING
If there is a possibility that the area where the device is stalled
could reach below 0°C, the device must be emptied of all water
contain ed. In case of freezing conditions disconnect the
incoming water pipe to drain the water heatercompletely.
MAINTENANCE
To maintain the machine at maximum efficiency, have qualified
personnel perform a maintenance check at least once a year.
Before cleaning or performing maintenance,
opening or disassembling the panels, switch off the device and
turn off the gas supply. Check the main burner and the pilot
flame, the ignition electrode, the safety valve and that there is
no leakage.
Check that there is nothing obstructing the passages within the
exchanger smoke channel.
To clean the outside of the panels, utilize a cloth with soap and
water.
Do not use solvents, powders, or abrasive sponges.
Do not clean the device and/orits parts with flammable material
s (e.g. petrol, alcohol, diesel etc.).
Troubleshooting: problems and solutions
Fault code
It will immediately shut down all gas channels
and display the fault code on the screen whe
n the controller detects a fault.
Fault Code meaning
E1：Ignition failure (Including ignition failure caused by low voltage).
E2：Ignition failure for the second time. (Including ignition failure
caused by low voltage).
E3：MCU self-check fault or EEPROM fault or wires fault.
E4：Temperature sensor of water outlet has open circuit or short
circuit.
E5：Temperature sensor of water inlet has open circuit or short
circuit（When the temperature sensor of water inlet is include d）.
E6：False fire.
E7：The overheating thermostat has open circuit.
E8： Temperature of water outlet is over 85
℃
℃ .
E9：Continuously working time（When this function is available）.
Fault Code Solution
1. When the display appears the fault code except for E7, after
solving the problems, there are two methods to remove the fault
co de。
①Press ON/ OFF button to restart for two times, then fault code
can be removed
②Remove and install the battery or turn off and open the water
tap.
2. When the display appears the fault code E7,or the display appe
ars other fault codes for 5 times in 15 minutes, display appear fa
ult code and “nL ,”the only solution is to press DOWN button for
more than 5 seconds. Then the fault code can be removed。
9
148.00 mm
210.00 mm

Malfunction Sheet
For the best functioning of the water heater, to prolong its lifetime
and ensure that it is always safe, ensure that it is inspected at
least once a year by a trained professional. The trained
professional is to perform the following maintenance operations:
-Remove any rust from the burner
-Remove any deposit on the glow plug by the electrode
-Clean the combustion tank
-Check the ignition, switching off and general functionality of the
device
-Check that the gas and water tubes and connections are sealed
Warning: the flowing repair instructions are only to be
performed by qualified and authorized technicians.
Malfunctions
Causes
Fire goes out during use No ignite after turning on The flame bursts Flame is yellow Abnormal flame with peculiar smell Difficult ignition Outlet water temperature is too low Outlet water temperature is too high Fire does not ignite at low temp.position. Fire is not out after water heater is off.
Remedies
Flue is blocked up.●Check the flue and make sure it is not blocked up.
Gas valve is not open.●Fully open gas valve or replace gas tank.
Gas valve is half open.●Fully open gas valve
There is air inside gas valv
e.
●Repeatedly turn on and off the outlet water valve until t
he water heater ignites successfully.
Gas pressure is too high.●●●Contact with maintenance personnel
Gas pressure is too low.● ● Contact with maintenance personnel
Freezing ●Contact with maintenance personnel
Inlet water pressure is not e
nough.
● ● ● ● Contact with maintenance personnel
Burner is blocked.● ● ● Contact with maintenance personnel
Heat exchanger is blocked.● ● ● Contact with maintenance personnel
Water controlling device def
ect
● ● ● ● ● Contact with maintenance personnel
Pulse ignition defect ● ● Contact with maintenance personnel
Internal wires loose ● ● Contact with maintenance personnel
Batteries are put at wrong t
erminals
●Put the batteries correctly
Electromagnetic valve defe
ct
● ● Contact with maintenance personnel
Feedback electrode defect ●Contact with maintenance personnel
Discharge distance or part i
s abnormal.
●Contact with maintenance personnel
Inlet water valve is not open
ed.
●Fully open inlet water valve
Fresh air is not enough.● ● ● Contact with maintenance personnel
10
148.00 mm
210.00 mm

Certificate of warranty –TTulpe®
TTulpe® guarantees appliances that it supplies in accordance wit
h European directive 1999/44/ECguaranteeing the sale of Consu
mer Goods for a period of two years against a lack of conformity a
ppearing after delivery of the product.
Unless proven otherwise,it will be assumed that any lack of confor
mity that appears in the six months from the delivery did not exist
when the goods were delivered.
The warranty for spare parts will have a duration of two years fro
m the date of delivery of the equipment.
This guarantee is only and exclusively valid for equipment sold an
d installed on EU territory.
Scope of the warranty
Unless proven otherwise,it is understood that the goods comply
with and are suitable for the purpose for which they were purchas
ed,and are always used under the following conditions:
• The guaranteed equipment must correspond to the equipment
that the manufacturer expressly intends for the country of desti
nation and must be installed in thatcountry.
• The necessary spare parts will be those determined by our OFFI
CAL Technical Department,and in all cases will be TTulpe origi
nal parts.
• The warranty is valid provided that the normal maintenance ope
rations,described in the technical instructions supplied with th
e equipment,are carried out.
• The consumer must inform TTulpe of a lack of conformity within
a period of less than two months after discovering it.
The warranty does not cover incidents caused by:
Freezing,although it can be that your device is equipped with an
anti-freeze protection,is any damage due to frost out of warranty.
• The electrical supply of equipment by generators or any other sy
stem that is not a stable electrical network with sufficient capacit
y.
• Products that have undergone any repair not carried out by TTul
pe’s OFFICAL Technical Department and/or personnel authori
zed by TTulpe.
• Corrosion,deformation,etc., caused by inadequatestorage.
• Handling of the product by anyone outside of TTulpe during the
warranty period.
• Assembly not in accordance with the instructions supplied with
the equipment.
• Installation of the equipment that does not respect the Laws an
d Regulations in force (electricity,hydraulics,etc.).
• Defects in the electric or hydraulic facilities,or due to insufficie
nt flow etc.
• Faults caused by the incorrect treatment of supply water to the
equipment,by corrosion originating from water hardness,by p
oorly carried out descaling treatments etc.
• Faults caused by atmospheric agents (ice,lightning,floods etc.)
as well as by erratic currents.
• Inadequate maintenance,neglect,or improper use.
The material replaced under warranty will remain the property of
TTulpe®
NOTE:It is essential to complete all the information requested in t
he Certificate of Warranty.The validation of the warranty must be
done immediately,by filling in the date and sending it immediatel
y to TTulpe B.V.All our OFFICIAL Technical Departments have the
corresponding accreditation from TTulpe®.Request this accredit
ation for any intervention.
Potential claims must be made to the competent authority in thi
s matter
.
11
148.00 mm
210.00 mm

TTulpe B.V.
Wester Boekelweg 21a,1718 MJ,Hoogwoud
Nederland
www.ttulpe.com
[e-mail]
Tel:[phone]
11/20
148.00 mm
210.00 mm