TUHOME Furniture LINEN CABINET User manual

ASSEMBLY INSTRUCTIONS
LINEN CABINET

2
Index
Hi! my name is
Armando, and I’ll be
with you while you
assemble this cabinet.
What will you need?
Where should you start?
What’s in the hardware bag?
Let’s start assembling!
Our last recommendations for taking care of your cabinet
2
3
How much weight does your cabinet resist?
How do the dowels and Minifix system work?
(We also explain what they are)
4
5-6
7
23
24
What will you need?
A flat, smooth surface. You can use the
cardboard of the box or a rug.
An electric screwdriver isn’t necessary, but it
can make the work much easier :)
Phillips head screwdriver Flat head screwdriver
Hammer

3
Where should you start?
(When the cabinet is already assembled
there’s no warranty for this)
This is so IMPORTANT!
Over the next few pages is the
panel and hardware content for this
cabinet.
Please make sure that the quantity
of each one is correct, and that
everything is in good shape.
A - x1
B - x1
C - x1
D - x1
E - x1
F - x1
FC - x4
G - x1
H - x1
I - x2
J - x1
K - x2
L - x4
LDC - x4
LIC - x4
M - x4
N - x1
O - x1
P - x2
Panel quantity

4
What’s in the hardware bag?
x58
Wood dowel
x40
Minifix cam
Spreading bolt
x40
Cover caps
x42
x16
Drywall
screw Nail-on glide
x4
2"
x8
Handle Screw
x4
Slides +
screws
x24
1 1/8“
Drywall
screw
x2
Wall anchor
+ screw
2"
Handle
x4
Metalic
handle
x1

5
Be careful!, try not to lose anything from this bag, its
content it’s neccesary for assembling you cabinet.
In case something is missing, please call to our
customer service
x2 x1
Glass door
hinge
Magnetic
stop
Glass door
x1

6
How do the dowels and Minifix system work?
Wood dowels
this is so important too!
They are little wooden cylinders.
1Put in the dowel
inside the indicated
hole and softly hit it
until it’s fully inside.
Everytime you’re using one of these
connectors during the assembly, you
should follow these same steps.
2When joining two
panels together, don’t
forget to gently hit
the panels to adjust
the joint.
Minifix system
It’s a joint compound of two parts: a spreading bolt and a Minifix cam.
2You should insert these cams
with the little arrow pointing
towards the drilling on the
panel’s edge (shown on the
left).
3This is a spreading bolt.
You should put it with the
black plastic part facing down.
4After joining two panels
together you should turn the
cams 180° with a phillips
head screwdriver to adjust
and secure the joint.
1This is a Minifix cam.
It has a little arrow on its
upper surface.
small arrow

7
Let’s start assembling!1
You can see the last page of this manual to have
a full look of the panels of this cabinet.
A
A
Turn this
panel over

8
2
3
E
F

9
4
5
G
H

10
6
7
F
G
H
A
F
G
H

11
E
A
F
G
H
Ix2
8
9

12
10
J
J
Turn this
panel over
11
Px2

13
Kx2
12
13
J
P
I

14
14
15
B
Drawer slides installation
To begin, you must take out the smaller part of the slide, pushing
down the black plastic part shown below:
(apply for steps 14 and 16)
Take the bigger part of
the slide and place it
over the panel. The
plastic stop shoud go
towards the back.
Front
2 11
B
I
K
K
J
I
P

15
16
17
C
2 11
If you want to recall how to
install this part of the slides,
go to the 14th step again.
C
I
B
P
K
K
I
J

16
18
19
D
Slide the back panel
inside the grooves.
O
N
BJ
K
KC

17
very carefully!
Turn over
the cabinet
KK
J
B
C
D
H
G
E
F
20

18
21
*Dimensions in inches
On the wall, measure and mark the points shown below.
Drill on the markings with a 5/16" drill bit.
Insert the wall anchors inside the drillings.
Place the cabinet and secure it with the screws.
1
2
3
4
Fix your cabinet to the wall
I
6,3 2,832,83
65,72 2,5

19
LICx4
LDCx4
L
LDC
LIC
Drywall
screw 2"
Take tha smaller part of the
slide and place it over the
panel. The metallic stop
should go at the front. Front
22
23x4

20
24x4
M
L
LIC
FC x4
25
Slide the back panel
inside the grooves.