Tunstall ID-Lock Smart User manual

ID-Lock Smart
Installation guide
Version 1.3

ID-Lock Smart Installation guide - Ver. 1.3
2
Contents
ID-Lock Smart Overview ........................................................................................................ 3
Advantages ....................................................................................................................... 3
W at is ID-Lock Smart? ..................................................................................................... 3
How does ID-Lock Smart work? ......................................................................................... 4
Installation of ID-Lock Smart ................................................................................................. 5
Package contents wit part numbers ................................................................................ 5
Split mec anics (036-01-835 or 036-01-836) ................................................................. 5
Handles (346 60 04-95) & cover plate (346 60 04-96) .................................................... 5
Carelock ACE Split (036-01-902) .................................................................................... 5
TM2-box (046-01-803) ................................................................................................... 5
IDT (K2415).................................................................................................................... 5
Exploded view of t e Split mec anics ................................................................................ 6
Tools needed for installation ............................................................................................. 7
Installation of t e TM2-box ............................................................................................... 7
Installation of t e IDT ........................................................................................................ 8
Step by step installation of t e Carelock ACE Split ............................................................. 9
Additional information ........................................................................................................ 27
Tx75 transmitters ........................................................................................................ 27
IDT zone-IDs ................................................................................................................ 27

ID-Lock Smart Installation guide - Ver. 1.3
3
ID-Lock Smart Overview
Advantages
T e main advantages wit ID-Lock Smart are:
• Greater safety and security in everyday life
• Greater sense of control over residents own accommodation
• A stress factor less for t e staff, especially during t e nig t
• Battery operation allows for cost-effective installation
• Possible for staff to open wit remote transmitters, mobile p ones or p ysical keys
• Possible to log all events
What is ID-Lock Smart?
ID-Lock Smart is a lock system t at prevents unwanted access to rooms in a nursing ome or
similar indoor environments. It is not designed for ig security applications, suc as
external doors to a resident ome or office.
You can always open doors in an ID-Lock Smart installation from t e inside by just pulling
t e door andle wit out any key or transmitter, w ile t e outside andle only works w en
t e door is unlocked. Many otel rooms use t is same functionality.
T e residents only need to wear a small pendant transmitter in order to unlock t e doors
t ey ave access to, wit out any manual interaction.
T e staff can unlock all doors t ey ave access to wit a special staff transmitter or mobile
p one, or wit a regular (p ysical) key.
T e ID-Lock Smart system consists of a position transmitter (IDT), a control box (TM2) and
an electronic lock mounted over t e door’s andle.
T e electric lock as a sleek design. It is mounted on t e inside of t e resident’s door,
wit out affecting eit er t e door or t e lock-case.
Because t e electrical lock is completely battery-powered, no expensive electrical
installations are required in t e door itself. T e only electrical requirement is t e availability
of a 12V or 24V DC source close to t e door to power t e IDT and t e TM2-box.

ID-Lock Smart Installation guide - Ver. 1.3
4
ow does ID-Lock Smart work?
T e IDT, w ic is mounted next to eac door, is transmitting an RF signal wit a zone-ID t at
is unique to eac door. T e signal as a range of approx. 1 to 1.5 meters. T e IDT RF signal is
marked in red in t e illustration below.
W en a resident’s Tx75 transmitter detects t e IDT signal, it will automatically transmit its
own ID, toget er wit t e detected zone-ID from t e IDT, to t e TM2-box. T e Tx75
transmitter as an ID t at is unique for eac transmitter on a site.
T e staff Tx75 transmitters work t e same way, except t ey do not automatically transmit
anyt ing; you must pus t e transmitter’s button to trigger t e transmission.
T e Tx75 signals are marked in green in t e illustration below.
T e TM2-box is configured to accept certain Tx75 IDs and a certain IDT zone-ID. W en an
accepted combination is received, it will send a Bluetoot signal to t e lock w ic will
engage t e door’s outer andle, and t e door can be opened by pulling t e andle. T e
Bluetoot signal is marked in blue in t e illustration below.
TM2-box
Staff Tx75
transmitter
IDT
Resident Tx75
transmitter
Carelock
ACE Split

ID-Lock Smart Installation guide - Ver. 1.3
5
Installation of ID-Lock Smart
Package contents with part numbers
T is is w at a complete ID-Lock Smart package s ould contain, including part numbers for
individual sub-kits:
Split mechanics (036-01-835 or 036-01-836)
See exploded view on t e next page for more
details.
T ere are two versions of t is kit wit different
part numbers for different door t icknesses.
Part number for t e complete kit is:
• 036-01-835 for 40 mm doors
• 036-01-836 for 60 mm doors
T e Main Spindle, t e Steel wires and t e
screws are t e only parts t at differs depending
on door t ickness.
andles (346 60 04-95) & cover plate (346 60 04-96)
Most existing andles do not ave a strong enoug
return spring, w ic is w y you s ould always use t e
andles from t is kit.
Carelock ACE Split (036-01-902)
T is is t e motor part, w ic is like a Carelock ACE but
wit different software configuration.
TM2-box (046-01-803)
T is is t e box t at listens to Tx75 transmitters and
controls t e Carelock ACE Split. It can also be triggered
from a wired signal. Requires 10-30 V DC, 350 mA.
IDT (K2415)
T is is t e position transmitter t at gives a unique zone-
ID to any Tx75 transmitter t at is wit in range (1 to 1.5
meters). Requires 10 – 28 V DC, 1 A.

ID-Lock Smart Installation guide - Ver. 1.3
6
Exploded view of the Split mechanics
Item Name
1 Satellite bottom
2 Top cabinet
3 Main spindle
4 Circlip
5 Wire sleeve
6 Toot module
7 Support roller
8 Steel wire
9 Spring
10 Outer wire sleeve
11 Outer spacer
12 Outer spindle
13 Limit bracket
14 Door plate
15 S im was er

ID-Lock Smart Installation guide - Ver. 1.3
7
Tools needed for installation
T ese are t ings you will need w en you install ID-Lock Smart. In addition to t is, you may
need a large cutter or acksaw to cut t e screws. You will also need wires and a power
supply for t e TM2-box and IDT, some means of fastening t e TM2-box (see below for an
example) and finally t e ID-Lock Config app for Android.
Screwdriver PH2
Screwdriver T25
Circlip plier
Lit ium grease
Installation of the TM2-box
T is is one example ow you may mount t e TM2-box. Ot er examples are to mount it
inside a plastic box or ide it above t e ceiling.
Make a simple mounting plate by using a metal- or plastic plate t at you drill oles in and
attac to t e TM2 box wit 7 mm wide screws made for plastic as illustrated ere.
T e TM2 box s ould ideally be placed close to t e Carelock ACE lock, especially if it will be
controlled by a Bluetoot device suc as a p one or a Bluetoot remote control transmitter,
since t e user is likely to old t eir device close to t e lock t ey are trying to open.
If t e TM2 box is only going to be controlled by Tx75 transmitters, it can be placed
anyw ere wit in Bluetoot range from t e Carelock ACE lock, w ic is typically 10 meters of
free line of sig t.

ID-Lock Smart Installation guide - Ver. 1.3
8
Carelock ACE Split as t e optional feature t at it will unlock t e door 10 seconds after it
loses its Bluetoot connection to t e TM2-box. T e idea be ind t is feature, w ic is
enabled by default, is to function as a security measurement in case of fire; you connect t e
TM2-box’s power supply to a power source t at will be cut off by t e fire alarm.
If you install t e TM2-box t is way, t e lock will unlock t e door 10 seconds after t e fire
alarm as cut off t e power to t e TM2-box (because t e Bluetoot connection will t en be
lost).
Installation of the IDT
T e IDT s ould be mounted next to t e door, preferably close to t e lock. If t ere are
several doors next to eac ot er in, e.g., a corridor, t en it is important t at all IDTs are
mounted on t e same side of t eir respective door. Two IDTs must never be closer t an 1
meter from eac ot er.
It may be necessary to adjust t e output power of t e IDT so t at t ey don’t overlap eac
ot er too muc . Inside t e IDT t ere is a potentiometer t at can be used for adjusting t e
output power; clockwise turn will increase t e power.
T e radiation from an IDT is close to equal in all directions, and it is not possible to s ield it
in one direction because t e frequency is so low (approx. 17 kHz). T is means t at t e IDT
field will radiate as muc inside of t e apartment as outside, causing t e ID-lock to trigger
t e lock also w en a resident is moving around inside t e apartment close to t e door. T is
is anot er reason w y you s ould lower t e output power as muc as possible, w ile
making sure t e system still works as intended.

ID-Lock Smart Installation guide - Ver. 1.3
9
Step by step installation of the Carelock ACE Split
Step 1
Remove t e inside t umbturn knob…
…and t e exterior cylinder ousing, w ic is fastened wit t e same screws.

ID-Lock Smart Installation guide - Ver. 1.3
10
Step 2
Unscrew t e t umbturn spindle bracket.
T e lock cylinder on t e doors exterior is fastened wit t e same screws as t e t umbturn
spindle bracket, so you want to old t e lock cylinder in place w ile you remove t e screws.
Remove t e t umbturn spindle…

ID-Lock Smart Installation guide - Ver. 1.3
11
…and remount t e bracket wit t e same screws t at also olds t e lock cylinder.
Step 3
Remove t e andles and t e spindle.

ID-Lock Smart Installation guide - Ver. 1.3
12
Step 4
Prepare t e satellite part by first mounting t e support roller and t en sliding on t e tooth
module.
Step 5
Mount t e circlip on t e outer spindle.

ID-Lock Smart Installation guide - Ver. 1.3
13
Step 6
Place t e steel wires inside t e outer wire sleeve.
Step 7
Temporarily use t e outer spindle to old t e steel wires in place by sliding it into t e outer
wire sleeve.

ID-Lock Smart Installation guide - Ver. 1.3
14
Step 7
Slide t e spring on to t e outer wire sleeve.
Step 8
T read t e outer wire sleeve assembly t roug t e door from t e outside.

ID-Lock Smart Installation guide - Ver. 1.3
15
Step 9
Mount t e satellite assembly from t e inside of t e door and let t e steel wires go t roug
t e tooth module. It is easier to do t is if you first rotate t e satellite assembly and t en
adjust it to a vertical position.
Step 10
Mount t e wire sleeve on t e tooth module and make sure t e steel wires are olding it.
Here you may want to use a screwdriver or ot er t in object and squeeze it slig tly in
between t e two steel wires.

ID-Lock Smart Installation guide - Ver. 1.3
16
Step 11
Mount t e circlip onto t e main spindle…
…followed by a shim washer.

ID-Lock Smart Installation guide - Ver. 1.3
17
Step 12
Now press t e main spindle assembly t roug t e top cabinet. It may be a narrow fit, so
some lig t force may be needed.
Step 13
Mount t e ot er shim washer…

ID-Lock Smart Installation guide - Ver. 1.3
18
…and t e last circlip onto t e main spindle in order to secure t e top cabinet.
Step 14
Slide t e top cabinet assembly t roug t e door. Rotate t e main spindle so t at t e steel
wires can slide t roug t e cavity in t e main spindle. Catc t e outer spindle on t e outside
of t e door t at was temporarily used to old t e steel wires in place in t e outer wire
sleeve, as it will be pus ed out by t e main spindle.

ID-Lock Smart Installation guide - Ver. 1.3
19
Step 15
Spray a little lit ium grease on t e t readed end of t e main spindle and inside t e outer
wire sleeve.
Step 16
Now press t e outer wire sleeve toward t e door and, w ile olding it depressed, turn t e
cogw eel t at protrudes from t e bottom of t e top cabinet assembly clockwise. T en,
wit out letting go of t e cogw eel, release t e pressure of t e outer wire sleeve and t en
let go of t e cogw eel. Now t e outer wire sleeve s ould stay retracted, allowing you access
to t e t readed part of t e main spindle.

ID-Lock Smart Installation guide - Ver. 1.3
20
Step 17
Screw on t e outer spindle until it comes to a stop, t en unscrew it between 180 to 270
degrees (½ to ¾ of a turn), and make sure it is aligned wit t e main spindle (t e outer wire
sleeve s ould be able to slide over t e outer spindle).
Step 18
Now release t e outer wire sleeve by rotating t e cogw eel counter-clockwise. T is ensures
t at t e outer spindle stays in place w en you mount t e andles.