Turboair TBC-50SD/SB User manual

Turbo air Speeds Up the Pace of Innovation
Horizontal Bottle Cooler
Installation and Operation Manual
Please read this manual completely before attempting to install or operate this equipment!
Full Stainless Steel Visible Exterior
TBC-50SD, 50SB/ TBC-95SD, 95SB
SD series: Stainless Steel Exterior
SB series: Black Laminated Vinyl Exterior
(This picture shows TBC-50SD in the SD series.)

SPECIFICATIONS............................................................................................ 2
SERIAL NUMBER............................................................................................ 2
INSTALLATION OF THE BOTTOM SHELVES..................................................3
INSTALLATION OF THE DIVIDERS.................................................................4
INSTALLATION OF THE OPENER KIT ............................................................5
HOW TO USE THE BOTTLE OPENER............................................................6
INSTALLATION .................................................................................................7
CLEANING & CAUTION ...................................................................................8
BASIC OPERATION..........................................................................................9
BEFORE REQUESTING SERVICE................................................................10
WARRANTY............................................................................................. 11~13
Horizontal Bottle Cooler
2
Turbo air
CONTENTS
SPECIFICATIONS
PAGE
MODEL COMP H.P. V/Hz REFRIGERANT AMPS WEIGHT
TBC-50SD/SB 1/3 115V/60Hz R-134a 6.8A 235
TBC-95SD/SB 1/2 115V/60Hz R-134a 9.2A 375
The serial number is located on the rating label which is on interior right side
wall.
Please retain the unit’s serial number for service purpose.
SERIAL NUMBER

3
Turbo air
* Note:
The size and quantities of the bottom shelves can be different according to
model number.
INSTALLATION OF THE BOTTOM SHELVES
1) Before adding cans or bottles to cooler, please install bottom shelves.
2) Then install dividers. (see page 4)

4
Turbo air
INSTALLATION OF THE DIVIDERS
1) To re-position divider, push back wards.
2) Spring in back of divider point ‘C’ will be shorten to about 1/2 inch.
3) Front of divider will be able to remove from point ‘A’ and ‘B’.
4) Position divider in the hole, point ‘C’ where you would like it.
5) Push divider back wards.
6) Insert front of divider in the holes, point ‘A’ and ‘B’, where you would like it.
* Note :
The shape and quantities of the dividers can be different according to model
number.
‘A’
‘B’
‘C’

5
Turbo air
INSTALLATION OF THE OPENER KIT
1) Bottle opener kit is inside cabinet.
2) On the front outside wall of bottle cooler, there are screws.
3) Hook the opener kit onto the screws, like drawing 1.
4) Push down so head of screw will insert into smaller opening, like drawing 2.
5) To detach it, follow above list in the reverse order.
12

6
Turbo air
1. In direction of arrow.
2. Grip the bottle tightly so it will not fall on removing cap.
3. The cap will drop to bottom of opener case.
4. When opener case is full, separate from cabinet.
5. Turn opener case over to empty.
HOW TO USE THE BOTTLE OPENER

7
Turbo air
1. GOOD AIR CIRCULATION
- Do not place any object that will restrict air flow in front or back grills.
- Turbo air highly recommends that there is ample space in rear of unit. 3 inches or
more is best.
2. PLACE ON STRONG GROUND
- Be sure the location chosen has a floor strong enough to support the total weight of
the cabinet and contents.
3. DO NOT PLACE NEAR HEAT
- Be sure to avoid hot corners and locations near stoves.
- High ambient temperature will make cooling efficiency lower.
4. INDOOR USAGE ONLY
- Be sure to install this unit indoor, so it will not get wet from the rain.
5. STABILIZING
- Make sure the unit is installed in a stable condition.
6. LEVELING
- Be sure that the unit is level from front to back and side to side.
7. Do not plug in with other units on same breaker.
8. Do not run on extension cord.
INSTALLATION

8
Turbo air
CLEANING
1. POWER CORD
- Be sure the power cord is connected to the proper voltage.
- A protected circuit of the correct voltage and amperage must be run for connection of
the line cord.
-Turn ‘off’ the power switch before disconnecting the power cord, whenever
performing maintenance functions or cleaning the refrigerated cabinet.
- Compressor warranties are void if compressor burns out due to low voltage.
2. RE-STARTING
- If disconnected, wait 5 minutes before re-starting.
3. POSITIONING DRINKS
- Do not obstruct the air inlet which is located at the back inside of the unit.
CAUTION
Before cleaning, turn unit off at power switch.
1. CLEANING THE INTERIOR AND EXTERIOR
- The interior and exterior of the unit can be cleaned using warm water with soap.
- Do not use an abrasive cleaner because it will scratch the surface.
2. CLEANING THE CONDENSER FINS
- To maintain proper refrigeration performance, the Condenser coil must be free of
dust, dirt, and grease.
This will require periodic cleaning. Condenser fins should be cleaned at least every
three months (90 days) or as needed.
- To clean condenser, unplug at power cord. Condenser can be cleaned with vacuum.
brush, or CO2(high pressure air).
3. CLEAN THE DRAIN PAN
- Empty the Drain Pan which is located under the unit, periodically.
- When reinstalling Drain Pan, make sure Drain Hose is placed back in pan.
4. CHECK AFTER CLEANING
- Plug unit back in and turn on power switch.
- Check that the unit is operating properly.

9
Turbo air
BASIC OPERATION
TBC-50SD
TBC-50SB
TBC-95SD
TBC-95SB
1. The controller(thermostat) is located at the right inside of the unit.
2. The factory setting for the control is ‘Normal’, and maintains about 38˚F (3˚C) inside.
3. Set toward “Cool” for warmer temperature and “Cold” for colder temperature.
4. The thermostat controls compressor’s cycling by sensing inside temperature.
5. When unit will not be used for a long time, turn the power switch off located under the
thermostat knob.
REFRIGERATORS
OFF
COOL
COLD
NORMAL
Temperature Controller
(Thermostat)

10
Turbo air
BEFORE REQUESTING SERVICE
SYMPTOMS CAUSES SOLUTIONS
Cooler is freezing
products
The unit does not
refrigerate at all.
The unit does not
refrigerate well.
There is a loud noise.
There are dew-drops
on the unit exterior.
There are dew-drops
on the unit interior.
•Thermostat set too cold.
•There is a power connection
failure problem.
•The unit is in sunlight or near a
heating device.
•Product was put in warm.
•The unit lid is opened too
frequently or left open too long.
•The temp. dial is not on the
correct position.
•The condenser is clogged.
•The floor is too weak or the
leveling feet are set incorrectly.
•The backside of the unit is too
close to the wall.
•High-moisture air can produce
dewdrops during rainy seasons.
•The lid is opened too frequently
or left open too long.
•Turn the temperature dial to a
warmer setting.
•Check the power cord to make
sure the unit is pluged in it
correctly.
•Move out of sunlight or away
from heater.
•Check the condition of stored
product.
•Check the position of the temp
control dial.
•Check the installation.
•Wipe with a dry cloth.
•Keep the lid closed to remove
dewdrops.
The following points are not malfunctions:
•A water-flowing sound can be heard when the compressor stops.
This is the sound of REFRIGERANT flowing.
•The compressor does not run during the defrost cycle.