TUSHY TUSHY SPA User manual

KNOW YOUR TUSHY
TEMPERATURE
CONTROL KNOB
NOZZLE
ADJUSTER
NOZZLE, WHICH
SPRAYS YOUR BUM
SEAT BRACKETS
WATER PRESSURE
CONTROL KNOB
CONGRATULATIONS
You have seized the bidet! Your butt, the
environment and the world will be better off
because of it. Install your TUSHY (using our
cheeky instructions inside this lil booklet) and
flaunt that shiney hiney! Happy pooping.
TUSHY SPA
HOW TO PUT THIS SHIT TOGETHER
HELLOTUSHY.COM
HELLOTUSHY.COM/SPAINSTALL
[email protected]
FB.COM/HELLOTUSHY
INSTAGRAM.COM/HELLOTUSHY
Check out our installation video at
HELLOTUSHY.COM/SPAINSTALL
and some common setup hacks at
HELLOTUSHY.COM/HACKS
YOU MIGHT ALSO NEED
Plastic Tube
(300cm)
Teflon
Tape
Wrench Screwdriver
Flexible Hose
(60cm)
Mini Adapter +
Rubber Washer
+
Rubber Pads
for Toilet Seat
Mega Adapter +
Rubber Washer
+
INCLUDED PARTS
Flush your toilet to drain the tank completely. Hold
down that flusher until it empties! (A couple inches
of water is okay.)
TOILET TANK
2.
Flip up the screw caps behind the seat with a flat
head screwdriver to access the screws. You may
need to hold the bolt beneath the screw with your
other hand while unscrewing. Remove the seat and
set aside. Dealing with a unique toilet seat?
Check out HelloTushy.com/hacks for some tips.
TOILET SEAT
3.
PREP WORK
Turn off the water valve near the toilet and the warm
water supply under the sink in small increments to
avoid damage, especially to older valves. There may
be some mineral build up - slow and steady wins the
race. Try twisting it in one direction and then the
other, each time rotating a little further until it’s free
to turn all the way around.
WATER VALVES
1.

Attach the flexible hose to the mega adapter for
connection to your TUSHY. Use a wrench to tighten
it if necessary, but do not over tighten.
COOL WATER CONNECTION
5.
WARM WATER CONNECTION:Thread the other
end of the plastic tube from the warm water
connection through the plastic fastener and onto
the labeled port under your TUSHY. Tighten the
fastener.
COOL WATER CONNECTION: Connect the other
end of the flexible hose from the cool water
connection to the labeled port under your TUSHY.
Make sure all the connections are secure and turn
on one water supply at a time. Use teflon tape if
there are any leaks.
Now for the big moment ... place the TUSHY on top
of your toilet and align the seat brackets with your
toilet seat mounting holes. (Optional: Use rubber
pads provided between the toilet seat mounting
holes and TUSHY to prevent the seat from moving
after attaching over TUSHY)
Make sure the nozzle is centered to your toilet bowl
for that precise spray of water. Secure the toilet
seat on top of the TUSHY by threading the toilet
seat bolts through the seat fasteners and the
mounting holes.
Now sit down, relax, doo your business. Use the
temperature and pressure control knob & let the
spray begin!
LEAKY JOINTS?
Plug these freaky leaky connections by wrapping teflon tape on the threading of
the pipe clockwise while maintaining some tension on it. Leave some room so that
there is no fraying of the tape when you are securing the adapters.
HELLOTUSHY.COM/TAPE
LEG ROOM FOR THE NOZZLE
Make sure that the bidet sits far enough from the rim of the toilet bowl so the
nozzle has enough room to swing up and back. You can do by just playing with
the nozzle adjuster on the bidet console.
Disconnect the existing flexible hose from your
toilet tank. To unscrew the connection, turn right.
(If you have a hard pipe, visit
HELLOTUSHY.COM/PARTS to get a flexible hose.)
Place the rubber washer in the mega adapter. Screw the
adapter onto the tank connection and then attach the
flexible hose to the bottom of the adapter. Do not over
tighten. Optional: Use teflon tape inside each connection.
Email us your questions at [e-mail] We’ve got your back!
Warm
Cool
FINISHING UP
6.
Reconnect the flexible steel hose to the other side of
the mini adapter using a wrench.
Unscrew the metal fastener from the mini adapter.
Grab the plastic tube and thread one end of the tube
through the fastener, then onto the mini adapter port
and tighten the fastener to secure the connection.
PSST!
Over-tightening the adapter can cause damage to the threads and result in water
leakage, so use only hand pressure at first. Rotate less than a quarter turn at a
time, checking as you go for leaks.
WARM WATER CONNECTION
4.
Disconnect the existing flexible steel hose from the warm
water supply valve with a wrench. (If you have a hard
metal pipe, visit HELLOTUSHY.COM/PARTS to get a
flexible hose.)
Place the rubber washer in the mini adapter. Fasten
the mini-adapter to the warm water supply valve using
your hand. Make sure it’s tight, but don't go nuts.
Optional: Use teflon tape inside each connection.
4.
5.
6.