Tuuci 1005116 Quick reference guide

1
|tuuci
1005116
ASSEMBLY & OPERATING INSTRUCTIONS Auto-Lift DUAL Cantilever with LED Light
step 1
remove all packaging from in and around umbrella
step 2
pull pin from cam lock and lift the handle to unlock umbrella
step 3
once you have Installed and leveled the stem using
the base installation instructions, slide the beauty
cover and umbrella over the security stem
(security stem is included with umbrella)
mast
beauty cover
security stem
step 4
lock umbrella down by pushing the cam lock handle in the
down position and lock with pin

2
|tuuci
1005116
ASSEMBLY & OPERATING INSTRUCTIONS Auto-Lift DUAL Cantilever with LED Light
Step 5
Install 2nd canopy frame by using 3/8 bushing and screws.
Note: add a drop of provided loctite to the end of the screw threads.

3
|tuuci
1005116
ASSEMBLY & OPERATING INSTRUCTIONS Auto-Lift DUAL Cantilever with LED Light
Step 6
Remove cap screw and mast cap and clip.
Step 7
Connect male and female light connectors.
Step 9
Insert 2nd grommet on outer mast groove and run
cable through clips.
Step 10
re-install cap and screws
Step 8
Insert 1st grommet on inner mast groove
by runing cables through clips
grommet (2)
cable clips
mast cap
cap screw
mast
female and male
connectors
grommet (1)
run cables through clips
clip

4
|tuuci
1005116
ASSEMBLY & OPERATING INSTRUCTIONS Auto-Lift DUAL Cantilever with LED Light
TO CLOSE UMBRELLA
To close umbrella, unlock the cart lock lever (by pushing cart handle upwards and pushing cart
lock lever in) then slide down the cart by pulling down the cart handle.
TO OPEN UMBRELLA
To open umbrella, unlock the carl lock lever and push cart handle up until it locks
cart lock
cart handle
Step 11
Gently separate each rib individually from center hub approx. 10 inches. If rib does not move easily do not force.
Inspect product for additional packaging.
cart lock
cart handle

5
|tuuci
1005116
ASSEMBLY & OPERATING INSTRUCTIONS Auto-Lift DUAL Cantilever with LED Light
When not in use the canopy should be carefully
folded and secured with the tie-strap.
OPERATING LIGHT SYSTEM
Step 1
Connect the electrical cord to the outlet.
Step 2
Tap plate above the nial once to power on-o, or touch and hold for light dimming control.
Power Supply:
Input Voltage 90 - 305VAC
Input Current 0.6A / 115VAC
0.3A / 230VAC
Output Voltage 12 VDC
Output Power 40 Watts
product is supplied with a 12ft power cord and plug.
2
Note:
close umbrella during wind conditions that exceed
manufacturer’s specications.
plate
1finial

ASSEMBLY & OPERATING INSTRUCTIONS CARE & MAINTENANCE
TUUCI frames are constructed from durable, marine-grade, weather-resistant materials including: fiberglass, armor-wall
aluminum, Dura-TEAK composites, Aluma-TEAK aluminum and sustainable hardwood. All fasteners (nuts, bolts, pulleys,
cam cleats, etc.) are marine-grade stainless steel and will withstand the most corrosive environments. Proper care and
maintenance is important to extend the serviceable life of all TUUCI products. We recommend the following:
•Fresh water rinses once a week
•Weekly inspection of your TUUCI product is recommended. Loose screws should be tightened and any broken
components replaced immediately to avoid further damage to your product.
•Prior to opening, ensure that the shade product is properly secured to an adequate shade anchor system.
•When opening a TUUCI parasol, separate each rib 10 inches from the center post, before raising the hub. Do not force
hub if it does not rise easily.
•When closing the parasol, pull the fabric out from between the struts to avoid pinching or damaging the TUFF-SKIN
canopy membrane.
•TUUCI recommends that all collapsible shade equipment be closed in wind conditions that exceed 25 MPH.
•Clean above-ground parasol bases regularly to maintain appearance. To clean, gently wash with soap and water using
a nonabrasive cloth or pad.
•Check bolts in security stem regularly to ensure that they remain fully tightened.
•Do not roll Aluma-crete (Aluminum Shell, Concrete Filled) bases on their side as damage to shell
or finish can occur.
•Do not use on stairways or over distances that exceed 50 feet, as damage to welded wheel tray may occur.
•Canopy should be cleaned regularly and can be cleaned without being removed from the frame. Hose down and clean
with a mild soap and lukewarm water (no more than 100° F.) using a soft bristle brush. Rinse thoroughly to remove
soap. Allow fabric to air dry.
•Do not use a pressure washer to clean canopies.