TVILIGHT SkyLite V3.1 External User manual

English
PR161926 | Rev. G | 05/10/2020
SkyLite V3.1External
Installation Manual

PR161926 | Rev. G | Page 2 of 10
TVILIGHT BV / Westerhaven 13, 9718 AW Groningen, the Netherlands
[phone] / [e-mail] / www.tvilight.com
In order to function properly, SkyLite v3.1 must be
connected to a dimmable driver/ballast.
NOTE: Some dimmable drivers/ballasts must be
programmed/set to dimmable mode. If this has not been
done, SkyLite v3.1 will not be able to dim the connected
luminaire.
ATTENTION:
TVILIGHT PROJECTS BV / Beechavenue 162-180, 1119 PS, Schiphol-Rijk, the Netherlands
[email protected] / www.tvilight.com

PR161926 | Rev. G | Page 3 of 10
In box:
You’ll need:
Pole ID Label
www.tvilight.com
TVI-SKLEXT1-01-0014
5.5m Cable
SkyLite V3.1
Generic Strap x 2
Max = 11mm
Min = 8mm
Wago x 2
OR
16 mm Grommet
M16 Cable Gland
Drill
M16 Threaded
OR
16 mm
Scan&Go App
Available in the
Apple App Store
and in the
Google Play Store

PR161926 | Rev. G | Page 4 of 10
2. Drill hole into the pole:
- M16 threaded (Cable Gland) OR
- 16 mm (Grommet)
5m
Note: For added protection against rust, the use of an anti-corrosion spray such as
WD40 Corrosion inhibitor or equal is recommended.
1. Push Cable Gland/Grommet over the cable
and UV Protective Sleeve
Note: Leave some UV Sleeve in the Cable Gland/Grommet.
OR

PR161926 | Rev. G | Page 5 of 10
3. Run wire into hole in the pole
4. Insert Cable Gland/Grommet into hole in
the pole
Twist the end
leads of the wires
OR
OR

PR161926 | Rev. G | Page 6 of 10
6. Strap product to the pole
5. Screw Cable Gland OR press Grommet into
the pole
* Ensure Tensioning Tool is set
to maximum tension (#4)
Tensioning Tool
NOTE: Make sure the UV Protective Sleeve is inside the Cable Gland/Grommet when
tightening.
OR

PR161926 | Rev. G | Page 7 of 10
7. Apply Pole ID Label to the pole
1 m
SAME
www.tvilight.com
TVI-SKLEXT1-01-0014
www.tvilight.com
TVI-SKLEXT1-01-0014
www.tvilight.com
TVI-SKLEXT1-01-0014
Ensure that the Product and Pole ID Labels match.

PR161926 | Rev. G | Page 8 of 10
www.tvilight.com
TVI-SKLEXT1-01-0014
www.tvilight.com
TVI-SKLEXT1-01-0014
8. Add device to CityManager
11. Download Tvilight Scan&Go from Apple iOS App Store or from Google Play Store.
2. Login with your Username and Password.
3. Use the ‘Add device’ function in Scan&Go app to add the device to CityManager.
4. The location of the new device is determined by Scan&Go’s GPS and it will be
indicated on the map.
5. The Device Serial Number will be added when scanning the QR-Code with the
camera.
6. Fill in the required fields (the ones with an asterisk), select the device type and
also select the type of ballast (PWM or DALI-Logarithmic or DALI-Linear).
Note: The type of ballast must be known before installation.
7. Press save and move to next device.
For more information on how to use Scan&Go app, please visit:
https://www.tvilight.com/scan-go/

PR161926 | Rev. G | Page 9 of 10
Wiring Diagram
GND N L DC+ DC-
Connector
(e.g. Wago)
N
L
DC-
DC +
Junction Box
GND
L
N
WARNING:
If not correctly connected product might not
function or it might be permanently damaged.

PR161926 | Rev. G | Page 10 of 10
GREY
0-10V-
or
DALI-
BLUE
N
BROWN
L
GREEN
GND
BLACK
0-10V+
or
DALI+
To Armature
To Mains
TVILIGHT
SKYLITE V3.1
GND NL
Driver
GND N L
0-10V-
or
DALI-
0-10V+
or
DALI+
0-10V-
or
DALI-
0-10V+
or
DALI+ N L
Wiring Diagram
WARNING:
If not correctly connected product might not
function or it might be permanently damaged.
Note: For added protection, an external circuit breaker at the power
input of the product is recommended. Circuit breakers such as
the ELeQ LS-94 5L2408 or similar rated products are acceptable.