TVILIGHT Gateway 3.1 User manual

English
Gateway3.1
Installation Manual
PR182335 | Rev. E | 03/12/2019

PR182335 | Rev. E | Page 2 of 15
TVILIGHT PROJECTS BV / Beechavenue 162-180, 1119 PS, Schiphol-Rijk, the Netherlands
NL [phone] / [email protected] / www.tvilight.com

PR182335 | Rev. E | Page 3 of 15
In box:
M16 Cable Gland
Pole ID Label
You’ll need:
5.5m Cable
Gateway v3.1
OR
20 mm Rubber Grommet
Drill M16 Threaded
OR
20 mm
Generic Strap x 2
Max = 13mm
Min = 8mm
Scan&Go App
Available in the
Apple App Store
and in the
Google Play Store

PR182335 | Rev. E | Page 4 of 15
1. Run wire through Cable Gland/Grommet
2. Drill hole into the pole:
- M16 threaded (Cable Gland) OR
- 20 mm (Grommet)
5m
Note: For added protection against rust, the use of an anti-corrosion spray such as
WD40 Corrosion inhibitor or equal is recommended.
OR

PR182335 | Rev. E | Page 5 of 15
3. Run wire through hole in the pole
4. Insert Cable Gland/Grommet into hole in
the pole
OR
OR

PR182335 | Rev. E | Page 6 of 15
5. Screw Cable Gland OR press Grommet into
the pole
OR
6. Strap product to the pole
THIS
SIDE
UP
* Ensure Tensioning Tool is set
to maximum tension (#4)
Tensioning Tool

PR182335 | Rev. E | Page 7 of 15
7. Apply Pole ID Label to the pole
Ensure that the Product and Pole ID Labels match.
SAME
www.tvilight.com
TVI-GW-01-0014
www.tvilight.com
TVI-GW-01-0014
www.tvilight.com
TVI-GW-01-0014
1 m

PR182335 | Rev. E | Page 8 of 15
www.tvilight.com
TVI-GW-01-0014
www.tvilight.com
TVI-GW-01-0014
8. Add device to CityManager
1. Download Tvilight Scan&Go from Apple iOS App Store or from Google Play Store.
2. Login with your Username and Password.
3. Use the ‘Add device’ function in Scan&Go app to add the device to CityManager.
4. The location of the new device is determined by Scan&Go’s GPS and it will be
indicated on the map.
5. The Device Serial Number will be added when scanning the QR-Code with the
camera.
6. Fill in the required fields (the ones with an asterisk), select the device type and
also select the type of ballast (PWM or DALI-Logarithmic or DALI-Linear).
Note: The type of ballast must be known before installation.
7. Press save and move to next device.
For more information on how to use Scan&Go app, please visit:
https://www.tvilight.com/scan-go/

PR182335 | Rev. E | Page 9 of 15
Wiring Diagram
AC in(N)
AC in(L)
Junction Box
AC in(L) AC in(N)
WARNING:
If not correctly connected product might not
function or it might be permanently damaged.

PR182335 | Rev. E | Page 10 of 15
Wiring Diagram
WARNING:
If not correctly connected product might not
function or it might be permanently damaged.
To Mains
(Naar Mains)
Armature
(Armatuur)
Tvilight Gateway
Junction Box
(Aansluitset)
L
L
L
L
N
N
N
N
GND
GND
GND
LNGND AC In(L) AC In(N)
BrownBlue
GND
Green
Note: For added protection, an external circuit breaker at the power
input of the product is recommended. Circuit breakers such as
the ELeQ LS-94 5L2408 or similar rated products are acceptable.

Appendix: Ethernet Cable Connection Instructions PR182335 | Rev. E | Page 11 of 15
Appendix: Ethernet Cable Connection
Instructions
A1. Remove the Vent Gland located at the
lower side of the GW
This appendix explains how to make an Ethernet connection in the Gateway v3.1.
Required Parts:
- 1 x Wiska Pressure Compensation Cable Gland ESVG 20, RAL 7035, M20
(Manufacturer Part #: 10060974)
- 1 x Wiska Reduction Sealing Insert, RDE 20, M20 (Manufacturer Part#: 10062185)
- Category 5, 6, or 7 Ethernet Cable (without Connector); 8 mm max Cable diameter
- 2 x RJ45 Connector for Ethernet Cable
Required Tools:
- RJ45 Ethernet Cable Crimping Tool

Appendix: Ethernet Cable Connection Instructions PR182335 | Rev. E | Page 12 of 15
A2. Insert and tighten the M20 Venting Cable
Gland in the open hole
A3. Remove Sealing Nut from the M20
Venting Cable Gland and insert the Reduction
Sealing Insert
Note: Installation Torque of Venting Cable Gland: 4 Nm

Appendix: Ethernet Cable Connection Instructions PR182335 | Rev. E | Page 13 of 15
A4. Put the Sealing Nut back onto the Venting
Cable Gland
A5. Run the Ethernet Cable (without
connector) through the Venting Cable Gland

Appendix: Ethernet Cable Connection Instructions PR182335 | Rev. E | Page 14 of 15
A7. Place connector onto Ethernet Cable and
crimp it into place
A6. Strip the Ethernet Cable

Appendix: Ethernet Cable Connection Instructions PR182335 | Rev. E | Page 15 of 15
A9. Tighten the Venting Cable Gland to
achieve a watertight seal between the Cable
Gland and the Ethernet Cable
Note: Installation Torque of Cap Nut: 3 Nm.
A8. Connect the Ethernet Cable to the
Ethernet port on the GW PCB