TVILIGHT TVI-GW-1 Series User manual

English
Gateway3.1
Installation Manual

Page 2 of 14
Version Author Date Changes Approved by
v1 Kepa Noguera
Idiondo
30/082017 Initial version of the
document
Henri Eskonen
v2 Henri Eskonen 22/12/2017 Minor formatting
v3 Kepa Noguera
Idiondo and Henri
Eskonen
07/06/2018 Merging grommet
and clable
gland versions;
add Appendix
for Ethernet
connection; minor
formatting
v3 - 07/06/2018
TVILIGHT BV / Rozenburglaan 3, 9727 DL, Groningen, the Netherlands
NL+31 (0)50 800 3240 / [email protected] / www.tvilight.com

Page 3 of 14
In box:
M16 Cable Gland
Pole ID Label
You’ll need:
M16 Threaded
OR
20 mm
Generic Strap x 2
Max = 13mm
Min = 8mm
5.5m Cable
Gateway v3.1
OR
20 mm Rubber Grommet
Drill

Page 4 of 14
1. Run wire through Cable Gland/Grommet
2. Drill hole into the pole:
- M16 threaded (Cable Gland) OR
- 20 mm (Grommet)
5m
Note: For added protection against rust, the use of an anti-corrosion spray such as
WD40 Corrosion inhibitor or equal is recommended.
OR

Page 5 of 14
3. Run wire through hole in the pole
4. Insert Cable Gland/Grommet into hole in
the pole
OR
OR

Page 6 of 14
5. Screw Cable Gland OR press Grommet into
the pole
OR
6. Strap product to the pole
THIS
SIDE
UP
* Ensure Tensioning Tool is set
to maximum tension (#4)
Tensioning Tool

Page 7 of 14
6. Apply Pole ID Label to the pole
Ensure that the Product and Pole ID Labels match.
SAME
www.tvilight.com
TVI-GW-01-0014
www.tvilight.com
TVI-GW-01-0014
www.tvilight.com
TVI-GW-01-0014
1 m

Page 8 of 14
Wiring Diagram
AC in(N)
AC in(L)
Junction Box
AC in(L) AC in(N)
WARNING:
If not correctly connected product might not
function or it might be permanently damaged.

Page 9 of 14
Wiring Diagram
WARNING:
If not correctly connected product might not
function or it might be permanently damaged.
To Mains
(Naar Mains)
Armature
(Armatuur)
Tvilight Gateway
Junction Box
(Aansluitset)
L
L
L
L
N
N
N
N
GND
GND
GND
LNGND AC In(L) AC In(N)
BrownBlue
GND
Green
Note: Observe all laws, guides and recommendations with regards to
electrical installation and safety.

Page 10 of 14
Appendix: Ethernet Cable Connection Instructions
Appendix: Ethernet Cable Connection
Instructions
A1. Remove the Vent Gland located at the
lower side of the GW
This appendix explains how to make an Ethernet connection in the Gateway v3.1.
Required Parts:
- 1 x Wiska Pressure Compensation Cable Gland ESVG 20, RAL 7035, M20
(Manufacturer Part #: 10060974)
- 1 x Wiska Reduction Sealing Insert, RDE 20, M20 (Manufacturer Part#: 10062185)
- Category 5, 6, or 7 Ethernet Cable (without Connector); 8 mm max Cable diameter
- 2 x RJ45 Connector for Ethernet Cable
Required Tools:
- RJ45 Ethernet Cable Crimping Tool