TVT Digital TD-9452A3-PA User manual

Package
Overview
Installation
1
2
3
4
► Connecting Network Cable
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■ Do not allow water or liquid intrusion into the camera.
Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating
temperature shall be -30˚C~60˚C), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
■
Quick Start Guide
Network Camera
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install the camera
under dry environment.
①
Then install the cover back to the camera and fix it firmly with the
screws. (Note that the cover should not be installed unevenly.)
Open the cover of the camera and then insert a micro SD card.
Camera Quick start guide
CD Plastic plug × 4
Drill template
4 tapping screws PA 4×25
1 machine screw PWM3×5
■ Please read this instruction carefully before operating the unit
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
2
13
* 1 It is recommended to install the security cap for outdoor installation.
* 2 If the PoE switch is used to power the camera, DC12V power supply is not
required.
Security cap
ALARM
4 3 2 1
ALARM
4 3 2 1
1
2
3
4
5
6
8
7
9
10
1--ALARM-COM
2--ALARM_OPEN
3--ALARM_INA
4--ALARM_GND
DC12V
16
27
38
49
510
Ethernet connector
Reset
Audio input connector
Audio output connector
Alarm input/output
Power connector
Speaker
Mounting base
Fixed ring
Micro SD card slot
Sensor
IPC
ALARM-INA
ALARM-GND
Alarm Input:
3
4
Alarm
Power
IPC
ALARM-COM
ALARM-OPEN +
+
-
-
Alarm Output:
1
2
► Connecting Alarm Input/Output

Network Connection
5
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
● Access the camera through IP-Tool
① Make sure that the camera and the PC are well connected via LAN.
② Find the IP-Tool from the CD and then install it in the computer.
After that, run the IP-Tool as shown below.
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 .168 . 226 . 201
255 . 255 . 255 . 0
192 .168 . 226 . 1
i
Tip: Enter the administrator password, and
then modify the network parameters.
Total Device: 3 Local IP Add ress:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Device Typ e IP Address Http Port Data Port Subnet Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 1 . 201
255 . 255 . 255 . 0
192 .168 . 1 . 1
Subnet Mask
Gateway
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X and the
gateway shall be changed to 192.168.1.1. After modification, please
enter the password of the administrator and click “Modify” button to
modify the settings.
The default password of the administrator is “123456”.
④ Double-click the camera listed in the IP-Tool or manually enter the
IP address in the address bar of the web browser to connect IP-CAM.
Then follow directions to download and install the plugin.
⑤ Enter the username and password in the login interface.
450043001346 A0
⑤
camera on a monitor and then loosen the fixed ring to adjust the view
angle of the camera.
Bracket adjustment. Before adjustment, preview the image of the
90° Tilt
360° Rotation 360° Pan
③
④ Secure the camera to the wall with the screws provided.
Route and connect the cables .
∅4.6
48.08mm
48.08mm
The default username is admin; the default password is 123456.
Fixed Ring
Insert a micro SD card
② Drill the screw holes and the cable hole on the wall according to
the drill template.
③ Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the
computer. Please modify the IP address of your device according
to the practical situation.
⑥ Tighten the fixed ring to complete the installation.