TVT Digital TD-9523A3 User manual

Package
Overview
Installation
1
2
3
4
Warning and Caution
■ If the product does not work properly, please contact your dealer or the
nearest service center. Never attempt to disassemble the camera yourself.
(We shall not be responsible for any problems caused by unauthorized repair
or maintenance.)
■ Do not allow water or liquid intrusion into the camera.
■ In the use of the product, you must be strict compliance with the electrical
safety regulations of the nation and region. When the product is mounted on
wall or ceiling, the device shall be firmly fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating temperature
shall be -30˚C~60˚C), dusty or damp locations, and do not expose it to high
electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for operating
environment.
Quick Start Guide
Network Camera
Camera Quick start guide
CD Plastic plug ×4
Drill template
Rubber plug Screwdriver
4 tapping screws
① Loosen the nut from the main element (security cap).
② Run the network cable (without RJ 45 connector) through the both
elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the nut and
the main cover.
■ Please read this instruction carefully before using the product and keep
it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without notice.
2
13
1 Ethernet Connector
2 Audio Input (MIC)
3 Audio Output (HP)
4 Alarm Input/Output
5 DC12V Power Connector*
6 Zoom-*
7 Zoom+ *
8 Micro SD Card Slot
9 Reset
10 CVBS Interface (unavailable)
* Please make sure that the wall or ceiling is strong enough to withstand 3
times the weight of the camera.
* Please install the camera in the dry environment. You'd better install back the
lower dome less than 4 hours after removing it.
* Do not remove the protection film until finishing the installation.
● Connecting Network Cable
* If the PoE switch is used to power the camera, DC12V power supply is not required.
* It is recommended to install the security cap for outdoor installation.
①
② Attach the drill template to the place where you want to fix the camera
and then drill 4 screw holes and 1 cable hole (if you want to route the cables
through the ceiling) according to the drill template.
Rotate the trim ring anticlockwise to remove it from the camera.
Trim Ring ∅4.6
90.2mm
90.2mm
Install Camera
Figure 1 Figure 2
1
3
4
5
9
9
6
7
8
8
10
2
ALARM
4 3 2 1
Security cap
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
DC12V
ALARM
4 3 2 1
Sensor
IPC
ALARM-INA
ALARM-GND
Alarm Input:
3
4
Alarm
Power
IPC
ALARM-COM
ALARM-OPEN
+
+
-
-
Alarm Output:
1
2
► Connecting Alarm Input/Output
(Type A)
(Type B)
* Only some models support T/W button. If your camera doesn’t have these two buttons, please
skip 6 and 7.

450043001389 A1
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 .168 . 1 . 201
255 . 255 . 255 . 0
192 .168 . 1 . 1
Subnet Mask
Gateway
For example, the IP address of your computer is 192.168.1.4. So the IP
address of the camera shall be changed to 192.168.1.X. After modification,
please enter the password of the administrator and click “Modify” button to
modify the settings.
The default password of the administrator is “123456”.
④ Double-click the IP address to open up the web browser or you can directly
enter the IP address in the address bar of the web browser. Then follow directions
to download the plug-in. After that, enter the user name and password in the login
interface to login.
The default username is admin; the default password is 123456.
Transparent Dome Maintenance
Transparent dome is an optical element which is made of plastics. As dirt, dust or
fingerprints on the dome will reduce the clarity of the image, please keep it clean in the
course of installing or using but do not directly touch or wipe it. If there is any dirt or
dust, please follow these cleaning tips to clean your dome camera.
* If there is dust on the dome, please use a dry soft brush to gently brush it .
* If there is water or grease on the dome, please gently wipe off the water or grease with
a soft cloth. Then use another clean cloth with a little neutral detergent to wipe it
several times until it is clean. Finally, dry it with a soft cloth.
* If there are fingerprints on the dome, please use a clean cotton cloth or lens cleaning wipe
with a little neutral detergent to wipe it several times and then dry it with a soft cloth.
Tips
③ Loosen the screws to open the lower dome.
④ Route and connect these cables. Then secure the camera to the
ceiling or wall with the screws provided.
Hold it and rotate
Rubber plug
Lower dome
Install Camera with Junction Box
⑤ Three-axis adjustment. Before adjustment, preview the view angle of the
camera on a monitor and then adjust the camera according to the figure
below to get an optimum angle.
Rotation 0°~345°
Tilt 0°~77°
Pan 0°~345°
Zoom+
Zoom-
⑦
put the trim ring onto the lower dome and then rotate it clockwise until it
is locked. Finally, remove the protection film softly.
Install the lower dome back to the camera and fix it with screws. Then
⑥ Insert a micro SD card. Then adjust the image of the camera by
pressing T or W button. Before adjustment, view the image of the
camera on a monitor.
Figure 3
Figure 5
Figure 4
Figure 6
①
②
③ Route and connect these cables(take side conduit cabling for example).
Then fasten the camera to the junction box with screws.
Fix the junction box to the wall with screws.
Rotate the trim ring anticlockwise to remove it from the camera and
then loosen the screws to open the lower dome (See Figure1 and 3).
④
⑤
Insert a micro SD card. Then adjust the view of angle and the image (See
Figure 4 and 5 ).
Install the lower dome back to the camera and fix it with screws. Then
put the trim ring onto the lower dome and then rotate it clockwise until it
is locked. Finally, remove the protection film softly. (See Figure6)
Network Connection
5
● Access the camera through IP-Tool
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
① Make sure that the camera and the PC are connected via LAN.
② Find the IP-Tool from the CD and then install it in the computer. After
that, run the IP-Tool as shown below.
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 226 . 201
255 . 255 . 255 . 0
192 .168 . 226 . 1
i
Tip: Enter the administrator password, and
then modify the network parameters.
Total Device: 3 Local IP Address:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Devic e Type IP Address Http Port Data Port Subnet Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
③ Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the above
table to show the network information on the right hand. Modify the IP
address and gateway of the camera and make sure its network address is in
the same local network segment as the computer’s. Please modify the IP
address of your device according to the practical situation.
Insert a micro SD card
* Install it when routing the cables
through the ceiling.
Note: Only some models support T/W button. If your camera doesn’t have these two
buttons, please skip the above zoom adjustment.