TVT Digital TD-9622E User manual

IP Speed Dome Camera
■ Please read this instruction carefully for correct use of the
product and preserve it for reference purposes.
■ All the examples and pictures used here are for reference
only.
■ There may be several technically incorrect places or printing
errors in this manual. The updates will be added into the new
version of this manual. The contents of this manual are subject
to change without notice.
1. Interfaces and Parts
① LAN
② HP Audio Out
③ MIC In
④ Alarm In/Alarm Out
⑤ Power
◆ Install SD Card
◆ Install the Speed Dome Alarm Connection:
1. Alarm Input
a) There is one independent alarm input port (ALM-IN1) and
one grounding port (ALM-GND).
b)Alarm input(NO type): Connect DC5V~DC12V voltage
between the alarm input port( ALM-IN1) and the grounding port
(ALM-GND).
c) Alarm input(NC type): Disconnect the voltage between the
alarm input port(ALM-IN1) and the grounding port (ALM-GND).
2. Alarm Output
a) Support 1CH alarm output including OPEN, COM
connections.
b) Alarm output: One passive switch for user to connect alarm
devices; the alarm output state will be auto on/off according to
your setting.
23
2. Installation
Please make sure the wall is strong enough to bear the dome
camera’s weight. Please make sure the camera is powered off
during installation.
3. Connections
① Loosen the two screws of the dome. ② Open the cover and insert SD card.
③ Drill the screw holes on the wall according
to the drill template. Then insert the plastic
plugs into the holes.
⑤ Connect the cables and then hang the
bracket on the wall .
⑥ Fix the bracket to the wall with four
screws.
④ Drive the two screws to the holes indicated
by the arrows (left) and leave 12mm
clearance.
Power Connection:
4. IE Network Connections
In LAN, there are two ways to access. a. Access through
IP-Tool; b. Directly Access through IE Browser
You can connect the IP camera through LAN/WAN access.
Here take the IE browser (6.0) for example.
◆ LAN
1
① Pull the cables through the bracket. Mount the
speed dome to the bracket.
② Secure the speed dome to the bracket with
the screws.
Quick Start Guide
1
2
3
4
5
Insert SD card
24V A
24V B
Earth
HP Audio Out
Network Port
MIC IN
Power
ALM-OPEN
ALM-COM
ALM-GND
ALM-IN1
● Access the camera through IP-Tool
① Make sure that the camera and the PC are well connected
to the LAN.

456
● Directly Access Through IE
450043000245 A0
③ Modify the IP address. The default IP address of this camera
is 192.168.226.201. Click the information of the camera listed
in the above table to show the network information on the right
hand. Modify the IP address and gateway of the camera and
make sure its network address is in the same local network
segment as the computer’s. Please modify the IP address of
your device according to the practical situation.
For example, the IP address of your computer is 192.168.1.4.
So the IP address of the camera shall be changed to 192.168.1.X.
After modification, please input the password of the administrator
and click “Modify” button to modify the setting.
The default password of the administrator is “123456”.
④ Double-click the IP address and then the system will pop up the IE
browser to connect IP-CAM . IE browser will auto download
the Active X control. After downloading, a login window will pop
up as shown below:
Input the user name and password to login.
The default username is admin; the default password is 123456.
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP:80
Subnet Mask: 255.255.255.0 Data Port:9008
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera
for the first time.
① Set the IP address of the PC and the network segment should be as
the same as the default settings of IP-CAM. Open the network and
share center. Click “Local Area Connection” to pop up the following
window. Select “Properties” and then select Internet protocol
according to the actual situation (for example: IPv4). Next, click
“Properties” button to set the network of the PC.
② Open the IE Browser and input the default address of IP-CAM
and confirm. The IE browser will download Active X control
automatically.
③ After that, the login dialog box will pop up.
④ Input the default username and password and then enter to view.
③ Go to the router’s management interface through IE browser to
forward the IP address and port of IP-CAM in the “Virtual Server”.
④ Open the IE browser and input its WAN IP and HTTP port to
access the IP-CAM.
Port Config
IP Config Router Config
◆ WAN
Take access the device by the router or virtual server for example.
① Make sure the camera is well connected via LAN; Then log
in the camera via LAN and go to the System Congfig→Network
Config→Port menu to set up the port number.
② Enter System Config→Network Config→Wired menu to modify
the IP address.
Preset Description
Call Preset
Set Preset
Call No.90 Preset Run track 1
Run cruise 1
Run 2cruise
Run 3cruise
Run 4cruise
OSD menu
Enable random scan
Enable P-PSCAN
Set left border of P-PSCAN
Set right border of P-PSCAN
Set the boundary value of the
near and middle infrared light
Set the boundary value of the
middle and far infrared light
Set random scan; Task auto
call the beginning point
Call No.91 Preset
Call No.92 Preset
Call No.93 Preset
Call No.94 Preset
Call No.95 Preset
Call No.97 Preset
Call No.99 Preset
Set No.91 Preset
Set No.92 Preset
Set No.93 Preset
Set No.94 Preset three times
Set No.95 Preset three times
HTTP Port
Data Por t
RTSP Port
80
9008
554
Port Range
Start End Protocol
IP Address
Enable
Application
1 9007 9008
421000 21001
2 80 81
3 10000 10001
to
to
to
to
Both
Both
Both
Both
192.168.1. 201
192.168.1. 201
192.168.1. 166
192.168.1. 166
② Find the IP-Tool from the CD and then install it in the PC.
After that, run the IP-Tool as shown below.
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 .168 . 226 . 201
255 . 255 . 255 . 0
192 .168 . 226 . 1
i
Tip: Enter the admin istrator password, and
then modify the network para meters.
Total Device: 3 Local IP Add ress:192.168.1.4Subnet Mask :255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Device Typ e IP Address Http Port Data Port Subnet Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 .168 . 1 . 201
255 . 255 . 255 . 0
192 .168 . 1 . 1
Subnet Mask
Gateway