TW Audio T24 Quick start guide

T24 RIGGING DOCUMENTATION

page 2
• T24 RIGGING ELEMENTS page 3
• T24 RIGGING SETUPS page 6
1. Single Box rigging page 7
2. Two or more Boxes page 7
3. Cluster rigging page 10
4. Rigging clusters page 12

page 3
CBT24 – the Cradle Bar for the
T24. Mounted on top of the Box.
Please check the angling of the
Bar.
It has the same angling than the
T24 itself and can only be moun-
ted in one direction.
BBT24 – the Backbone of the
T24. This part gives you the
stability you need when moun-
ting two or more T24 on top of
each other.
T24 RIGGING ELEMENTS:
1
2

page 4
BCT24 – adapts the back-
bone (BBT24) to the cradle bar
(CBT24).
This element is used when rig-
ging two or more T24 w/out the
main cradle (MCT24).
The holes are also used as
pinpoints in the EASE FOCUS
simulation Data.
4
MCT24 – the main cradle.
Used for clustering 2 or more
T24 aside and underneath each
other.
You can interconnect multiple
MCTs for a larger cluster.
5
BAT24 – adapts the backbone
(BBT24) to the main cradle
(MCT24) when building a cluster
of 2 or more T24.
3

page 5
BLT24 - the Boxlinks. Used to
assemble T24s underneath each
other.
7
Now that we have gone through all the elements,
let’s take it step by step…
No – this is not a dead Octopus –
this is the ASK44.
The Rigging chain for the
MCT24.
6

page 6
The basic element for all rigging setups is the CBT24.
The following pictures show the correct assembling to the T24.
T24 RIGGING SETUPS:
MAKE SURE THAT THE CARGO STUDS ARE LOCKED
SECURELY!!!
! !

page 7
This is the most simple way of rigging
the T24 with a CBT24. Just as the
picture shows – this is a very simple
way of rigging the T24. When using
this rigging option, you will not have
the possibility of dedicated angling.
The angling can only be done by
straps, etc...
• Attach the CBT24 to the Box
• Mount the BCT24 w i t h i t s s c r e w s
to the CBT24.
• Attach the BBT24 t o t h e B o x b y
starting on the lower handle.
1. Single Box rigging
2. Two or more Boxes
rigged underneath each
other:

page 8
Open the pin to tilt the top part of the
BBT24 to attach it to the upper handle.
Lock the upper part of the BBT in the
upper handle by re-inserting the pin.
Attach the BBT to the BCT – Already con-
fused? Just do it like the following picture!
This is how it should look like when eve-
rything was done correctly.
PLEASE CHECK ALL CONNECTIONS AFTER MOUNTING
THE RIGGING ELEMENTS
! !
a b
c d

page 9
Now you can easily add up to 6 boxes underneath eachother. Therefore you need the
BLT24. Pull up the Box you have already rigged up to the height where you can set one
more Box underneath it. Then connect the next Box BBT to BBT and use the Boxlinks
(BLT24) to angle them.
The angling is done by the holes of the BLT24s. Every left out hole gives you 6° of angle.
This picture shows you an angle of 12°
inbetween the speakers. The overall angling
is done by the choice of the pinpoint in the
BCT24. The simulation can be done in EASE
FOCUS.
PLEASE CHECK ALL CONNECTIONS AFTER
MOUNTING THE RIGGING ELEMENTS
!

page 10
To get a dedicated angling not
only in vertical position, but also in
horizontal position you can use the
MCT24. With the Main Cradle it
is possible to hang multiple Boxes
underneath and side a side of
each other.
Again-we need the CBT24 and
the BBT24. This time we need two
shakles connected to the CBT24.
We also need the BAT24. The
Adaptions for the BBT to the Main
Cradle. Setup your speakers like
this:
Here you can see the two BATs
prepared. They are simply at-
tached to the BBTs via the top
Pin.
3. Cluster rigging