Twin Star Home 26MM1066 User manual

1
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
ATTENTION
IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL
OR CALL CUSTOMER SERVICE BEFORE YOU RETURN
THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.
For Customer Service:
www.twinstarhome.com
in English Call: 866-661-1218
ATTENTION
SI VOUS AVEZ DES PROBLÈMES OU QUESTIONS,
ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU
APPELEZ LE SERVICE À LA CLIENTÈLE AVANT DE RETOURNER
CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.
Pour le service à la clientèle:
www.twinstarhome.com
pour le service en français: 866-661-1219
ATENCIÓN
SI TIENE ALGÚN PROBLEMA O PREGUNTAS, ENVÍE UN
MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO
DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER ESTE
PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.
Servicio de atención al cliente:
www.twinstarhome.com
Línea para llamadas en español: 866-661-1219
STOP
ARRÊT
PARE
STOP
ARRÊT
PARE

1
Français p. 15
ELECTRIC FIREPLACE MANTEL
26MM1066
INSTRUCTION MANUAL
Español p. 8
MAXIMUM LOAD 10 lb. (4.5kg)
MAXIMUM LOAD 50 lb. (22.6kg)
CAUTION: This unit is intended for use only with the products and maximum weights
indicated. Use with other products or products heavier than the maximum weights
indicated may result in instability causing possible injury.
Note: Flat Panel TVs with base support should be placed squarely in the center of the
stand with no overhang on any side.
FIT UP TO 62” PLASMA/LCD TELEVISIONS
MAXIMUM LOAD 135 lb. (61.22 kg)
Requires-Electric Fireplace
Insert with Heater
ATTENTION
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China
Printed in China
www.twinstarhome.com
English Call: 866-661-1218
Spanish /French Call: 866-661-1219
For Customer Service:

2
PACKAGE CONTENTS
G
H
L
M
O
O
H
B
A
E
C
P
Q
N
N
F
I
J
K
D
Part Description Quantity
A Hearth/Base 1
B Center Left Side Panel 1
C Center Right Side Panel 1
D Center Front Panel 1
E Left Side Panel 1
F Right Side Panel 1
G Mantel/Top 1
H Wood Shelf 2
I Left Upper Side Panel 1
J Right Upper Side Panel 1
K Support Panel 1
L Left Front Door 1
M Right Front Door 1
N Center Back Panel 2
O Side Back Panel 2
P Center Shelf 1
Q Insert Support Bar 1

3
HARDWARE CONTENTS
Part Description
Bolt
Washer
32+1 extra
32+1 extra
32+1 extra
Quantity Picture
BB
AA
Wood Dowel
CC
Screw
Screw
Knob (with bolt)
Shelf Pin
38
12
2
8
DD
EE
GG
FF
Touch-up Pen 1
ZZ
SAFETY INFORMATION
WARNING
• Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.
Make sure you do not discard the hardware.
CAUTION
• Use care in assembling your new fireplace. Take your time and use the hardware
provided and a quality Phillips head screwdriver. Never overtighten bolts.
• Do not sit on any part of the mantel.
• All panels are labeled left and right as viewed from the front of unit.

4
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.
Estimated Assembly Time: 60 Minutes
Tools Required for Assembly (not included): Phillips head screwdriver, scissors and utility knife
ASSEMBLY INSTRUCTIONS
Fig. 1
Hardware Used
EE
CC
Screw x 2
Wood Dowel x 4
1. Locate the Center Left Side Panel (B), Center Right
Side Panel (C), Center Front Panel (D), and set out
face down on a scratch-free surface.
Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Push the Center Left Side Panel and Center Right
Side Panel snug to the Center Front Panel. Make
sure the Wood Dowels are seated in the pre-drilled
holes.
Connect the Center Left Side Panel (B), Center
Right Side Panel (C) and Center Front Panel (D)
with Connection Plate, tighten Screws (EE) through
the pre-drilled holes.
B
CEE
DCC
CC
Fig. 2
2. Locate Hearth/Base (A) and set out finished side up
on the floor.
Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Attach the Completed assembly from step 1 to the
Hearth/Base (A). Make sure that dowels are seated
into the pre-drilled holes in the Hearth/Base. Using
Bolts (AA) and Washers (BB) attach panels through
pre-drilled holes in the mounting blocks.
HAND TIGHTEN ONLY.
Insert one Wood Dowel (CC) into each of pre-drilled
holes. Push the Right Side Panel (F) and Left Side
Panel (E) snug to completed assembly. Using Bolts
(AA) and Washers (BB) through the pre-drilled holes
in the mounting blocks.
HAND TIGHTEN ONLY.
Hardware Used
BB
AA
CC
Bolt x 8
Washer x 8
Wood Dowel x 8
BB
E
A
FAA
CC
CC

5
Fig. 3
Hardware Used
BB
AA
CC
Bolt x 10
Washer x 10
Wood Dowel x 8
3. Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Locate the Center Shelf (P) on the top of the
assembly from the step 2, as shown in diagram.
Make sure that dowels are seated into the pre-drilled
holes.
Using Bolts (AA) and Washers (BB) attach these
panels through pre-drilled holes in the mounting
blocks.
HAND TIGHTEN ONLY.
P
AA
BB
CC CC
Fig. 4
Hardware Used
Hardware Used
BB
BB
AA
AA
CC
CC
Bolt
Bolt
x 6
x 6
Washer
Washer
x 6
x 6
Wood Dowel
Wood Dowel
x 6
x 6
Fig. 5
5. Insert one Wood Dowel (CC) into each of the
pre-drilled holes on the top edges of the Assembly
from step 4. Then locate Mantel/Top (G) and lay
finished side up on top of completed assembly. From
the inside, attach Mantel/Top (G) using Bolt (AA) and
Washer (BB) through the pre-drilled holes in the
mounting blocks.
HAND TIGHTEN ONLY.
Using Phillips head screwdriver tighten all Bolts
alternating top and bottom, left and right.
4. Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Push Support Panel (K) snug to the Center Shelf (P),
tighten Bolt (AA) and Washer (BB) through the
pre-drilled holes.
Locate upper side panels (I, J) on the top of the
assembly from the step 3, as shown in diagram.
Make sure that dowels are seated into the pre-drilled
holes.
Using Bolts (AA) and Washers (BB) attach these
panels through pre-drilled holes in the mounting
blocks.
HAND TIGHTEN ONLY.
I
AA
AA
AA
BB
BB
BB
J
CC
CC CC
G
CC
K

6
Fig. 6
Hardware Used
EE Screw x 36
6. Attach Side Back Panels (O) to the back of the
completed assembly from step 5. Use a Phillips head
screwdriver, tighten Screws (EE) through the
pre-drilled holes in the Side Back Panels (O).
EE
N
GG
O
O
Fig. 7
Fig. 8
7. Rest Center Back Panels (N) into groove on Mantel
Top (G) back edge. Allow the pre-installed magnets
to keep the Center Back Panels (N) in closed
position.
DD
L
M
Hardware Used
DD
GG
Knob
(with bolt)
Screw
x 2
x 12
8. Connect the Right Front Door (M) to the Right Side
Panel (F) with the hinge pre-installed on the door,
then use a Phillips head screwdriver to tighten the
Wood Screw (GG) through the pre-drilled holes.
REPEAT WITH LEFT FRONT DOOR (L) ON
OPPOSITE SIDE.
Attach the Knob (DD) to the Left Front Door (L) and
Right Front Door (M), use the bolts attached through
the pre-drilled holes in the doors. Then use a Phillips
Head Screwdriver to tighten the bolts.

7
Fig. 10
Completed
Unit
Electric
Fireplace Insert
Install
Insert
From
Back
10. PLEASE READ ALL “ELECTRIC FIREPLACE
INSERT” INSTRUCTIONS PRIOR TO
INSTALLING ELECTRIC INSERT IN YOUR
COMPLETED FIREPLACE MANTEL. INSTALL
THE INSERT IN YOUR FIREPLACE CLOSE TO
ITS FINAL POSITION.
Lift insert carefully into the back of the unit and
center in the insert opening. Do not drag insert
across hearth/base as it may scratch the unit.
Connect the Insert Support Bar (Q) to the inside left
and right panels, using the bolt (AA) and washer
(BB) through pre-drilled holes.
MOVE YOUR COMPLETED UNIT ONLY SHORT
DISTANCES. MOVE COMPLETED UNIT WITH
GREAT CARE. IT TAKES TWO PEOPLE TO
MOVE COMPLETED UNIT INTO ITS FINAL
POSITION.
Hardware Used
BB
AA Bolt x 2
Washer x 2
Q
AA BB
Fig. 9
Hardware Used
FF Shelf Pin x 8
9.Choose desired height of wood shelf (H) and place
the four shelf pins (FF) into shelf holes inside side
panels. Insert wood shelf (H), allowing wood shelf
(H) to rest on the shelf pins (FF). Repeat as desired
for remaining wood shelf (H).
H
FF

8
Français p. 15
CHIMENEA ELÉCTRICA
26MM1066
INSTRUCCIÓN DE MONTAJE
English p. 1
PRECAUCIÓN: Esta unidad está diseñada para ser usada únicamente con los
productos y con los pesos máximos indicados. El uso con otros productos, o con
productos de peso mayor a los pesos máximos indicados, puede producir inestabilidad,
lo que posiblemente causaría lesiones.
Note: Los televisores de pantalla plana con soporte de base deben colocarse
perfectamente en el centro de la base del gabinete, sin que ninguno de los laterales
sobresalga.
Necesitará, Además, El
Hogar Eléctrico Con Calentador
ATENCIÓN
Twin-Star International, Inc.
Delray Beach, FL 33445
Fabricado en China
Impreso en China
www.twinstarhome.com
Inglés llamadas:: 866-661-1218
Español /Français llamadas: 866-661-1219
Servicio de atención al cliente:
CARGA MÁXIMA: 10 LIBRAS (4.5 KILOS)
CARGA MÁXIMA: 50 LIBRAS (22.6 KILOS)
APTO PARA TELEVISORES DE PLASMA O LCD DE 42” a 62”
CARGA MÁXIMA: 135 LIBRAS (61.22 KILOS)

9
Pieza Descripción Cantidad
A Base Del Hogar 1
B Panel Central – Lado Izquierda 1
C Panel Central – Lado Derecho 1
D Panel Delantero Central 1
E Panel Lateral Izquierda 1
F Panel Lateral Derecho 1
G Repisa/Parte Superior 1
H Estante De Vidrio 2
I Panel Lateral Superior Izquierda 1
J Panel Lateral Superior Derecho 1
K Panel de Soporte 1
L Puerta Delantero Izquierda 1
M Puerta Delantero Derecho 1
N panel posterior central 2
O paneles posteriores laterales 2
P Estante Central 1
Q Barra De Soporte Para El Inserto 1
CONTENIDO DEL PAQUETE
G
H
L
M
O
O
H
B
A
E
C
P
Q
N
N
F
I
J
K
D