Twin-Star International 26MM2490 User manual

1
ATTENTION
IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL
OR CALL CUSTOMER SERVICE BEFORE YOU RETURN
THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.
For Customer Service: www.twinstarhome.com
in English Call: 866-661-1218
in Spanish Call: 866-661-1218
in French Call: 866-374-9203
ATENCIÓN
SI TIENE ALGÚN PROBLEMA O PREGUNTAS,
ENVÍE UN MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO
DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER
ESTE PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.
Servicio de atención al cliente: www.twinstarhome.com
Línea para llamadas en inglés: 866-661-1218
Línea para llamadas en español: 866-661-1218
Línea para llamadas en francés: 866-374-9203
STOP STOP
PARE PARE
ATTENTION
SI VOUS AVEZ DES PROBLÈMES OU QUESTIONS,
ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU APPELEZ LE
SERVICE À LA CLIENTÈLE AVANT DE RETOURNER
CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.
Pour le service à la clientèle : www.twinstarhome.com
pour le service en anglais, composez le 866-661-1218
pour le service en espagnol, composez le 866-661-1218
pour le service en français, composez le 866-374-9203
ARRÊT ARRÊT
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO

1
ELECTRIC FIREPLACE MANTEL
26MM2490
ASSEMBLY INSTRUCTION
ALSO Requires-ElectricALSO Requires-Electric
Fireplace Insert with HeaterFireplace Insert with Heater
www.twinstarhome.com
In English call: 866-661-1218
In French call: 866-374-9203
In Spanish call: 866-661-1218
ATTENTION
For Customer Service:
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in Vietnam
Printed in Vietnam
Españo p. 7
Français p. 13
MAXIMUM LOAD 30 lb. (13.6kg)
CAUTION: This unit is intended for use only with the products and maximum weights
indicated. Use with other products or products heavier than the maximum weights
indicated may result in instability causing possible injury.
Note: Flat Panel TVs with base support should be placed squarely in the center of the
stand with no overhang on any side.
FIT UP TO 65” PLASMA/LCD TELEVISIONS
MAXIMUM LOAD 135 lb. (61.22 kg)

2
Part Description Quantity
A Hearth/Base 1
B Center Left Front Panel 1
C Center Right Front Panel 1
D Center Shelf 1
E Left Side Panel 1
F Right Side Panel 1
G Mantel/Top 1
H Wood Shelf 2
I Center Back Panel 1
J Side Back Panel 2
K Drawer 1
L Left Front Door 1
M Right Front Door 1
N Insert Suppport Bar 1
O Center Front Panel 1
P Center Upper Back Panel (pre-installed) 1
PACKAGE CONTENTS
G
H
I
J
J
K
L
MN
O
H
D
B
A
E
C
F
P

3
HARDWARE CONTENTS
Part Description
Bolt
Washer
Wood Dowel
Shelf Pin
Screw
Knob (with bolt)
Tipping Restraint
Hardware
23
23
24
8
34
6
2
Quantity Picture
(Shown to size)
BB
CC
DD
EE
FF
GG
AA
SAFETY INFORMATION
WARNING
• Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.
Make sure you do not discard the hardware.
CAUTION
• Use care in assembling your new fireplace. Take your time and use the hardware
provided and a quality Phillips head screwdriver. Never overtighten bolts.
• Do not sit on any part of the mantel.
• All panels are labeled left and right as viewed from the front of unit.
Touch-up Pen 1
ZZ

4
ASSEMBLY INSTRUCTIONS
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.
Estimated Assembly Time: 60 Minutes
Tools Required for Assembly (not included): Phillips head screwdriver, scissors and utility knife
F
Hardware Used
Hardware Used
BB
BB
EE
AA
AA
CC
CC
Bolt
Bolt
x 4
x 8
Washer
Washer
Screw
x 4
x 8
x 2
Wood Dowel
Wood Dowel
x 8
x 8
2. Locate Hearth/Base (A) and set out finished side up
on the floor. Insert one Wood Dowel (CC) into each
of the pre-drilled holes.
Attach the Completed Center Front assembly from
step 1 to the Hearth/Base (A). Make sure that
dowels are seated into the pre-drilled holes in
the Hearth/Base. Using Bolts (AA) and Washers
(BB) attach panels through pre-drilled holes in
the mounting blocks.
HAND TIGHTEN ONLY.
Locate Left Side Panel (E) and Right Side Panel (F),
insert one Wood Dowel (CC) into each of the
pre-drilled holes on the bottom edge of the panels.
Then use Bolts (AA) and Washers (BB) through the
pre-drilled holes in the mounting blocks. Attach the
Side Panels to Hearth / Base (A).
HAND TIGHTEN ONLY.
1. Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Push the Center Left Side Panel (B) and Center
Right Side Panel (C) snug to the Center Front Panel
(O) and Center Shelf (D). Make sure the Wood
Dowels (CC) are seated in the pre-drilled holes.
Then use Bolts (AA) and Washers (BB) through the
pre-drilled holes in the mounting blocks.
Connect the Center Left Side Panel (B), Center
Right Side Panel (C) and Center Front Panel (O)
with Connection Plate, tighten Screws (EE)
through the pre-drilled holes.
HAND TIGHTEN ONLY.
Fig. 1
C
E
B
AA
BB
ACC
BB
EE
AA
D
O
Fig. 2

5
Hardware Used
Hardware Used
Hardware Used
BB
AA
CC
Bolt x 9
Washer x 9
Wood Dowel x 8
3. Insert one Wood Dowel (CC) into each of the
pre-drilled holes on the top edges of the Assembly
from step 2. Then locate Mantel/Top (G) and lay
finished side up on top of completed assembly.
From the inside, attach the Mantel/Top (G) using
Bolts (AA) and Washers (BB) through the pre-drilled
holes in the mounting blocks.
HAND TIGHTEN ONLY.
Using Phillips head screwdriver tighten all Bolts
alternating top and bottom, left and right.
Fig. 4
Fig. 3
Fig. 5

4. Insert Center Upper Back Panel (P) into the groove
in the top of the cabinet as diagram 1. Push Center
Upper Back Panel (P) to connect the magnets with
the metal slip as diagram 2.
Locate Side Back Panel (J) and Center Back Panel
(I), attach to the back of the completed assembly
from step 3. Use a Phillips Head screw driver,
tighten screws (EE) through the pre-drilled holes in
the Back Panels to the completed assembly.
5. Locate Right Front Door (M) and Left Front Door
(L). Slide door hinge keyhole into panel hinge
bracket. (Diagram 1)
Use Phillips Head Screwdriver to tighten screws.
(Diagram 2)
TO ADJUST HINGES
To adjust door forward or backward change keyhole
slot position. (As Shown In Diagram 3a)
To adjust door right or left loosen/tighten screw.
(As Shown In Diagram 3b)
To adjust door up or down adjust bracket height.
(As Shown In Diagram 3c).
Attach the Knob (FF) to the Left Front Door (L) and
Right Front Door (M), use the bolts attached
through the pre-drilled holes in the doors. Then use
a Phillips Head Screwdriver to tighten the bolts.
Carefully align the metal tracks on the left and
right sides of the box with the extended
glides. Make sure Drawer (K) are aligned and
centered in Cabinet, then gently push the Drawer
(K) into place.
CAUTION: Do not force the drawer into place, as
the cabinet might be damaged as a result.
CC
AA
BB
EE
FF
I
P
J
M
K
L
J
G
EE
FF
Screw
Knob
x 42
x 6

6
Fig. 7
Fig. 6
6. Choose desired height of Shelf (H) and place the
four Shelf Pin (DD) into same height shelf holes
inside side panels. Insert Wood Shelf (H), allow
Wood Shelf (H) to rest on the Shelf Pin (DD).
The Mantel must be level for the proper functionality
of doors and as a safety precaution. There are lev
elers located under the mantel, the height can be
increased by twisting counter-clockwise.
7. PLEASE READ ALL “ELECTRIC FIREPLACE
INSERT” INSTRUCTIONS PRIOR TO INSTALLING
ELECTRIC INSERT IN YOUR COMPLETED
FIREPLACE MANTEL. INSTALL THE INSERT IN
YOUR FIREPLACE CLOSE TO ITS FINAL
POSITION.
Lift insert carefully into the back of the unit and
center in the insert opening. Do not drag insert
across hearth/base (A) as it may scratch the unit.
Connect the Insert Support Bar (N) to the inside left
and right panels, using the bolt (AA) and washer
(BB) through pre-drilled holes.
MOVE YOUR COMPLETED UNIT ONLY SHORT
DISTANCES. MOVE COMPLETED UNIT WITH
GREAT CARE. IT TAKES TWO PEOPLE TO MOVE
COMPLETED UNIT INTO ITS FINAL POSITION.
Hardware Used
Hardware Used
BB
AA
DD
Bolt
1/4 in. x 1-1/4 in.
Shelf Pin
x 2
x 8
Washer
1/4 in. x 3/4 in. x 2
H
DD
Completed
Unit
Electric
Fireplace Insert
Install
Insert
From
Back
N
AA BB

7
8. We have included two Tipping Restraints for this
unit. You must install this hardware to prevent
accidents or injuries. When properly installed,
this restraint can provide protection against
unexpected tipping of the Unit due to small
tremors, bumps or climbing. We strongly
recommend mounting this hardware to a wall
stud and your Unit.
Warning: You must install the Tipping Restraint
Hardware to help prevent accidents or damage
to the unit.
Hardware Used
GG Tipping Restraint
Hardware x 2
Fig. 8
Cabinet Wall Stud
Wall
GG
GG
GG

8
26MM2490
CARGA MÁXIMA 135 lb. (61.22 kg)
PRECAUCIÓN: Esta unidad está diseñada para ser usada únicamente con los
productos y con los pesos máximos indicados. El uso con otros productos, o
con productos de peso mayor a los pesos máximos indicados, puede producir
inestabilidad, lo que posiblemente causaría lesiones.
Nota: Los televisores de Pantalla Plana con soporte de base deben colocarse
perfectamente en el centro de la base del gabinete, sin que ninguno de los laterales
sobresalga.
SOPORTA TELEVISIONES PLASMA/LCD HASTA 65”
CHIMENEA ELÉCTRICA
Necesitará, Además, ElNecesitará, Además, El
Hogar Eléctrico Con CalentadorHogar Eléctrico Con Calentador
www.twinstarhome.com
Línea para llamadas en inglés: 866-661-1218
Línea para llamadas en francés: 866-374-9203
Línea para llamadas en español: 866-661-1218
ATENCIÓN
Servicio de atención al cliente:
Twin-Star International, Inc.
Delray Beach, FL 33445
Fabricado en China
Impreso en China
English. 1
Français p. 13
INSTRUCCIÓN DE MONTAJE

9
Pieza Descripción Cantidad
A Base Del Hogar 1
B Panel Frontal Izquierdo Central 1
C Panel Derecho Central 1
D Tabla Central 1
E Panel Lateral Izquierda 1
F Panel Lateral Derecho 1
G Repisa/Parte Superior 1
H Tabla De Madera 2
I Panel Posterior Central 1
J Paneles Posterior Lateral 2
K Cajón 1
L Puerta Delantera Izquierda 1
M Puerta Delantera Derecha 1
N Insert Suppport Bar 1
O Panel Central Delantero 1
P Panel Trasero Superior Central (pre-instalado) 1
G
H
I
J
J
K
L
MN
O
H
D
B
A
E
C
F
P
CONTENIDO DEL PAQUETE