Twin-Star International 26MM9404 User manual

1
Français p. 17
ELECTRIC FIREPLACE MANTEL
26MM9404
INSTRUCTION MANUAL
Requires-Electric Fireplace
Insert with Heater
E-mail: [e-mail]
In English call: 866-661-1218
In French call: 866-374-9203
In Spanish call: 866-661-1218
AT T ENT I O N
For Customer Service:
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China
Printed in China
Español p. 9
MAXIMUM LOAD 30 lb. (13.6kg)
CAUTION: This unit is intended for use only with the products and maximum weights
indicated. Use with other products or products heavier than the maximum weights
indicated may result in instability causing possible injury.
Note: Flat Panel TVs with base support should be placed squarely in the center of the
stand with no overhang on any side.
FIT UP TO 62”PLASMA/LCD TELEVISIONS
MAXIMUM LOAD 135 lb. (61.22 kg)
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
PDFMAILER.COM

2
PACKAGE CONTENTS
G
L
L
M
O
O
H
H
H
H
B
A
E
C
P
NF
I
J
K
D
Part Description Quantity
A Hearth/Base 1
B Center Left Side Panel 1
C Center Right Side Panel 1
D Center Front Panel 1
E Left Side Panel 1
F Right Side Panel 1
G Glass Top 1
H Glass Shelf 4
I Left Front Panel 1
J Right Front Panel 1
K Center Shelf 1
L Glass Door 2
M Left Top Panel 1
N Right Top Panel 1
O Side Back Panel 2
P Insert Support Bar 1
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
PDFMAILER.COM

3
HARDWARE CONTENTS
Part Description
Bolt
Washer
29+1 extra
29+1 extra
24+1 extra
Quantity Picture
(Shown to size)
BB
AA
Wood Dowel
CC
Suction Cup
Door Touch Clip
Pivot Hinge
Magnetic Spring Catch
Shelf Pin
Metal Support Post
Screw
Screw
8
2
4
2
16
8
34
8
DD
EE
FF
GG
HH
II
JJ
KK
Touch-up Pen 1
ZZ
Tipping Restraint
Hardware 2
LL
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
PDFMAILER.COM

4
SAFETY INFORMATION
WARNING
•Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.
Make sure you do not discard the hardware.
CAUTION
•Use care in assembling your new replace. Take your time and use the hardware
provided and a quality Phillips head screwdriver. Never overtighten bolts.
•Do not sit on any part of the mantel.
•All panels are labeled left and right as viewed from the front of unit.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.
Estimated Assembly Time: 60 Minutes
Tools Required for Assembly (not included): Phillips head screwdriver, scissors and utility knife
ASSEMBLY INSTRUCTIONS
Fig. 1
1. Locate the Center Shelf (K) and Center Front Panel
(D) on a scratchproof surface. Attach the Center
Shelf (K) and Center Front Panel (D) using Bolts
(AA) and Washers (BB) through the pri-drilled holes
and tighten .
AA
BB
D
K
Hardware Used
BB
AA
Bolt x 3
Washer x 3
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
PDFMAILER.COM

5
Fig. 2
I
J
CC
JJ
Fig. 3
Fig. 4
E
F
AA
AA
AA
B
BB
BB
BB
C
CC
CC
4. Locate Hearth/Base (A) and set out nished side up
on the oor.
Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Attach the Completed assembly from step 3 to the
Hearth/Base (A). Make sure that dowels are seated
into the pre-drilled holes in the Hearth/Base. Using
Bolts (AA) and Washers (BB) attach panels through
pre-drilled holes in the mounting blocks.
HAND TIGHTEN ONLY.
Insert one Wood Dowel (CC) into each of pre-drilled
holes. Push the Right Side Panel (F) and Left Side
Panel (E) snug to completed assembly. Using Bolts
(AA) and Washers (BB) through the pre-drilled holes
in the mounting blocks.
HAND TIGHTEN ONLY.
Hardware Used
Hardware Used
BB
BB
AA
AA
CC
CC
Bolt
Bolt
x 8
x 8
Washer
Washer
x 8
x 8
Wood Dowel
Wood Dowel
x 8
x 4
2. Locate the Left Front Panel (I), Right Front Panel
(J), the completed assembly from step 1. Insert one
Wood Dowel (CC) into each of the pre-drilled holes.
Push the Left Front Panel (I) and Right Front Panel
(J) snug to the completed assembly from step 1.
Make sure the Wood Dowels (CC) are seated in the
pre-drilled holes. Connect the Left Front Panel (I),
Right Front Panel (J) and completed assembly with
Connection Plate, tighten Screws through the
pre-drilled holes.
3. Insert one Wood Dowel (CC) into each of the
pre-drilled holes in the completed assembly form
step 2 .Attach the Completed assembly to the
Center Left Side Panel (B) and Center Right Side
Panel (C). Make sure that dowels are seated into the
pre-drilled holes. Using Bolts (AA) and Washers
(BB) attach panels through pre-drilled holes in the
mounting blocks.
HAND TIGHTEN ONLY.
Hardware Used
CC
JJ
Screw x 2
Wood Dowel x 4
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
PDFMAILER.COM

6
Fig. 5
Fig. 6
Fig. 7
N
M
DD
CC
O
JJ
O
GG
FF
KK
DD
L
L
7. Attach the Magnetic Spring Catch (GG) on the
bottom of Top Panel, tighten screws (KK) through
holes to the block as shown in diagram.
Place the Door Touch Clip (DD) to the glass door.
Insert the Pivot Hinge (FF) into the plastic mat as
shown in diagram. Then push the Glass Doors (L)
snug to the Pivot Hinges (FF), use a Phillips Head
Screwdriver to tighten the pivot hinge against the
glass.
WARNING
Do not over tighten catch screws.
Damage to the Glass could occur!
Hardware Used
DD
FF
GG
KK
Door Touch Clip
Pivot Hinge
Magnetic Spring
Catch
screw
x 2
x 4
x 2
x 8
Hardware Used
JJ
Screw x 32
6. Attach Side Back Panels (O) to the back of the
completed assembly from step 5. Use a Phillips
Head Screw Driver, tighten Wood Screws (JJ)
through the pre-drilled holes in the Side Back Panels
(O).
Hardware Used
BB
AA
CC
Bolt x 8
Washer x 8
Wood Dowel x 8
5. Insert Left Top Panel (M) and Right Top Panel (N),
from the inside, attach the Top panel using Bolts
(AA) and Washers (BB) through the pre-drilled
holes in the mounting blocks.
HAND TIGHTEN ONLY.
AA
AA
BB
BB
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
PDFMAILER.COM

7
Fig. 8
Fig. 9
HH
H
EE
G
II
Fig. 10
Completed
Unit
Electric
Fireplace Insert
Install
Insert
From
Back
P
AA BB
Hardware Used
Hardware Used
HH
EE
II
Shelf Pin
Suction Cup
Metal Support
Post
x 16
x 8
x 8
8.Choose desired height of Glass Shelf (H) and place
the four Shelf Pin (HH) into same height shelf holes
inside side panels. Insert Glass Shelf (H), allow
Glass Shelf (H) to rest on the Shelf Pin (HH).
9. Attach the Metal Support Post (II) and screw
clockwise into inset threads on the top of the mantel.
Insert the Suction Cups (EE) into the Support Posts,
with the help of another adult carefully lower the
Glass Top (G) onto the Support Posts.
10. PLEASE READ ALL “ELECTRIC FIREPLACE
INSERT”INSTRUCTIONS PRIOR TO
INSTALLING ELECTRIC INSERT IN YOUR
COMPLETED FIREPLACE MANTEL. INSTALL
THE INSERT IN YOUR FIREPLACE CLOSE TO
ITS FINAL POSITION.
Lift insert carefully into the back of the unit and
center in the insert opening. Do not drag insert
across hearth/base as it may scratch the unit.
Connect the Insert Support Bar (P) to the inside left
and right panels, using the bolt (AA) and washer
(BB) through pre-drilled holes.
MOVE YOUR COMPLETED UNIT ONLY SHORT
DISTANCES. MOVE COMPLETED UNIT WITH
GREAT CARE. IT TAKES TWO PEOPLE TO
MOVE COMPLETED UNIT INTO ITS FINAL
POSITION.
Hardware Used
BB
AA
Bolt x 2
Washer x 2
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
PDFMAILER.COM

8
LL
Fig. 11
11. We have included two Tipping Restraints for this
unit. You must install this hardware to prevent
accidents or injuries. When properly installed, this
restraint can provide protection against unexpected
tipping of the Unit due to small tremors, bumps or
climbing. We strongly recommend mounting this
hardware to a wall stud and your Unit.
Warning: You must install the Tipping Restraint
Hardware to help prevent accidents or damage to
the unit.
Hardware Used
Tipping Restraint
Hardware x 2
Cabinet Wall Stud
Wall
LL
03/08/11
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
PDFMAILER.COM