Twin-Star International 26MM9405 User manual

1
Français p. 15
ELECTRIC FIREPLACE MANTEL
26MM9405
INSTRUCTION MANUAL
Requires-Electric FireplaceRequires-Electric Fireplace
Insert with HeaterInsert with Heater
www.twinstarhome.com
In English call: 866-661-1218
In French call: 866-374-9203
In Spanish call: 866-661-1218
ATTENTION
For Customer Service:
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China
Printed in China
Español p. 8
MAXIMUM LOAD 30 lb. (13.6kg)
CAUTION: This unit is intended for use only with the products and maximum weights
indicated. Use with other products or products heavier than the maximum weights
indicated may result in instability causing possible injury.
Note: Flat Panel TVs with base support should be placed squarely in the center of the
stand with no overhang on any side.
FIT UP TO 62” PLASMA/LCD TELEVISIONS
MAXIMUM LOAD 135 lb. (61.22 kg)

2
PACKAGE CONTENTS
G
I
I
H
H
B
A
E
C
J
II
II
F
L
L
K
D
Part Description Quantity
A Hearth/Base 1
B Center Left Side Panel 1
C Center Right Side Panel 1
D Center Front Panel 1
E Left Side Panel 1
F Right Side Panel 1
G Glass Top 1
H Glass Shelf 2
I Side Back Panel 1
J Insert Support Bar 1
K Mantel/Top 1
L Glass Door 2

3
HARDWARE CONTENTS
Part Description
Bolt
Washer
20+1 extra
20+1 extra
20+1 extra
Quantity Picture
(Shown to size)
BB
AA
Wood Dowel
CC
Suction Cup
Door Touch Clip
Pivot Hinge
Magnetic Spring Catch
Shelf Pin
Metal Support Post
Screw
Screw
6
2
4
2
8
6
22
8
DD
EE
FF
GG
HH
II
JJ
KK
Tipping Restraint
Hardware
Touch-up Pen
2
1
LL
ZZ

4
SAFETY INFORMATION
WARNING
• Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.
Make sure you do not discard the hardware.
CAUTION
• Use care in assembling your new fireplace. Take your time and use the hardware
provided and a quality Phillips head screwdriver. Never overtighten bolts.
• Do not sit on any part of the mantel.
• All panels are labeled left and right as viewed from the front of unit.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.
Estimated Assembly Time: 60 Minutes
Tools Required for Assembly (not included): Phillips head screwdriver, scissors and utility knife
ASSEMBLY INSTRUCTIONS
Fig. 1
Hardware Used
JJ
CC
Screw x 2
Wood Dowel x 4
1. Locate the Center Left Side Panel (B), Center Right
Side Panel (C), Center Front Panel (D), and set out
face down on a scratch-free surface.
Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Push the Center Left Side Panel and Center Right
Side Panel snug to the Center Front Panel. Make
sure the Wood Dowels are seated in the pre-drilled
holes.
Connect the Center Left Side Panel (B), Center
Right Side Panel (C) and Center Front Panel (D)
with Connection Plate, tighten Screws (JJ) through
the pre-drilled holes.
B
C
JJ
DCC
CC

5
Fig. 2
2. Locate Hearth/Base (A) and set out finished side up
on the floor.
Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Attach the Completed assembly from step 1 to the
Hearth/Base (A). Make sure that dowels are seated
into the pre-drilled holes in the Hearth/Base. Using
Bolts (AA) and Washers (BB) attach panels through
pre-drilled holes in the mounting blocks.
HAND TIGHTEN ONLY.
Insert one Wood Dowel (CC) into each of pre-drilled
holes. Push the Right Side Panel (F) and Left Side
Panel (E) snug to completed assembly. Using Bolts
(AA) and Washers (BB) through the pre-drilled holes
in the mounting blocks.
HAND TIGHTEN ONLY.
3. Insert one Wood Dowel (CC) into each of the
pre-drilled holes on the top edges of the Assembly
from step 2. Then locate Mantel/Top (K) and lay
finished side up on top of completed assembly. From
the inside, attach Mantel/Top (K) using Bolts (AA)
and Washers (BB) through the pre-drilled holes in
the mounting blocks.
HAND TIGHTEN ONLY.
Hardware Used
Hardware Used
BB
BB
AA
AA
CC
CC
Bolt
Bolt
x 8
x 10
Washer
Washer
x 8
x 10
Wood Dowel
Wood Dowel
x 8
x 8
BB
BB
E
A
F
AA
AA
CC
CC
CC
CC
Fig. 3
Fig. 4
Hardware Used
JJ Screw x 20
K
JJ
I
I
4. Attach Side Back Panels (I) to the back of the
completed assembly from step 3. Use a Phillips
Head Screw Driver, tighten Wood Screws (JJ)
through the pre-drilled holes in the Side Back Panels
(I).

6
Fig. 5
Fig. 6
Fig. 7
5. Attach the Magnetic Spring Catch (GG) on the
bottom of Top Panel, tighten screws (KK) through
holes to the block as shown in diagram.
Place the Door Touch Clip (DD) to the glass door.
Insert the Pivot Hinge (FF) into the plastic mat as
shown in diagram. Then push the Glass Doors (L)
snug to the Pivot Hinges (FF), use a Phillips Head
Screwdriver to tighten the pivot hinge against the
glass.
WARNING
Do not over tighten catch screws.
Damage to the Glass could occur!
Hardware Used
Hardware Used
Hardware Used
HH
DD
EE
FF
II
GG
KK
Shelf Pin
Door Touch Clip
Suction Cup
Pivot Hinge
Metal Support
Post
Magnetic Spring
Catch
screw
x 8
x 2
x 6
x 4
x 6
x 2
x 8
6.Choose desired height of Glass Shelf (H) and place
the four Shelf Pin (HH) into same height shelf holes
inside side panels. Insert Glass Shelf (H), allow
Glass Shelf (H) to rest on the Shelf Pin (HH).
DD
GG
KK
FF
L
L
H
HH
EE
G
II
7. Attach the Metal Support Post (II) and screw
clockwise into inset threads on the top of the mantel.
Insert the Suction Cups (EE) into the Support Posts,
with the help of another adult carefully lower the
Glass Top (G) onto the Support Posts.

7
Fig. 8
8. PLEASE READ ALL “ELECTRIC FIREPLACE
INSERT” INSTRUCTIONS PRIOR TO
INSTALLING ELECTRIC INSERT IN YOUR
COMPLETED FIREPLACE MANTEL. INSTALL
THE INSERT IN YOUR FIREPLACE CLOSE TO
ITS FINAL POSITION.
Lift insert carefully into the back of the unit and
center in the insert opening. Do not drag insert
across hearth/base as it may scratch the unit.
Connect the Insert Support Bar (J) to the inside left
and right panels, using the bolt (AA) and washer
(BB) through pre-drilled holes.
MOVE YOUR COMPLETED UNIT ONLY SHORT
DISTANCES. MOVE COMPLETED UNIT WITH
GREAT CARE. IT TAKES TWO PEOPLE TO
MOVE COMPLETED UNIT INTO ITS FINAL
POSITION.
Hardware Used
BB
AA Bolt x 2
Washer x 2
Completed
Unit
Electric
Fireplace Insert
Install
Insert
From
Back
J
AA BB
Fig. 9
9. We have included two Tipping Restraints for this
unit. You must install this hardware to prevent
accidents or injuries. When properly installed, this
restraint can provide protection against unexpected
tipping of the Unit due to small tremors, bumps or
climbing. We strongly recommend mounting this
hardware to a wall stud and your Unit.
Warning: You must install the Tipping Restraint
Hardware to help prevent accidents or damage to
the unit.
Hardware Used
LL Tipping Restraint
Hardware x 2
Cabinet
Wall Stud
Wall
LL