TYAN FT48A-B7070 Quick start guide

FT48A-B7070
Service Engineer’s Manual

2
http://www.tyan.com
PREFACE
Copyright
This publication, including all photographs, illustrations, and software, is
protected under international copyright laws, with all rights reserved.
Neither this manual, nor any material contained herein, may be reproduced
without written consent of manufacturer.
Copyright 2015 MiTAC International Corporation. All rights reserved. TYAN®is
a registered trademark of MiTAC International Corporation.
Version 1.0
Disclaimer
Information contained in this document is furnished by MiTAC Computer
Corporation and has been reviewed for accuracy and reliability prior to printing.
TYAN®assumes no liability whatsoever, and disclaims any express or implied
warranty, relating to sale and/or use of TYAN®products including liability or
warranties relating to fitness for a particular purpose or merchantability. TYAN®
retains the right to make changes to produce descriptions and/or specifications
at any time, without notice. In no event will TYAN®be held liable for any direct
or indirect, incidental or consequential damage, loss of use, loss of data or
other malady resulting from errors or inaccuracies of information contained in
this document.
Trademark Recognition
All registered and unregistered trademarks and company names contained in
this manual are property of their respective owners including, but not limited to
the following.
TYAN®is a trademark of MiTAC Computer Corporation
Intel®is a trademark of Intel®Corporation.
AMI®, AMIBIOS® and combinations thereof are trademarks of AMI
Technologies.
Microsoft®, Windows®are trademarks of Microsoft Corporation.
Winbond®is a trademark of Winbond Electronics Corporation.

3
http://www.tyan.com
FCC Declaration
Notice for the USA
Compliance Information Statement (Declaration of Conformity
Procedure) DoC FCC Part 15: This device complies with part 15
of the FCC Rules
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following conditions:
·This device must not cause harmful interference.
·This device must accept any interference received, including
interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Notice for Canada
This Class A digital apparatus complies with Canadian ICES-003. Cet
appareil numérique de la Classe A est conforme àla norme NMB-003
du Canada.
Notice for Europe (CE Mark)
This product is in conformity with the Council
Directive 2004/108/EC..
CAUTION: Lithium battery included with this board. Do not puncture,
mutilate, or dispose of battery in fire. There will be danger of explosion if
battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by manufacturer. Dispose of used battery according
to manufacturer instructions and in accordance with your local regulations.

4
http://www.tyan.com
About this Manual
This manual provides you with instructions on supporting your FT48A-
B7070 barebones system. This manual is intended for experienced users
and integrators with hardware knowledge of personal computers.
This manual consists of the following parts:
Chapter 1:
Provides an introduction to the FT48A-B7070,
barebones,standard parts list, external components, list
the key components of motherboard and provicd block
diagram of the system .
Chapter 2:
A complete introduction of the procedures install the
CPU,memory, HDDs, and expansion cards
Chapter 3:
A complete introduction of the removal and replacement
precedures for the pre-installed components.
Appendix:
Reference lists for BIOS, cable connection table, FRU
Parts table for system setup, and technical support in case
a problem arise with your system.

5
http://www.tyan.com
Safety and Compliance Information
Before installing and using TYAN FT48A-B7070, take note of the following
precautions:
·Read all instructions carefully.
·Do not place the unit on an unstable surface, cart, or stand.
·Do not block the slots and opening on the unit, which are provided for
ventilation.
·Only use the power source indicated on the marking label. If you are not
sure, contact the power company.
·The unit uses a three-wire ground cable, which is equipped with a third pin to
ground the unit and prevent electric shock. Do not defeat the purpose of this
pin. If your outlet does not support this kind of plug, contact your electrician
to replace your obsolete outlet.
·Do not place anything on the power cord. Place the power cord where it will
not be in the way of foot traffic.
·Follow all warnings and cautions in this manual and on the unit case.
·Do not push objects in the ventilation slots as they may touch high voltage
components and result in shock and damage to the components.
·When replacing parts, ensure that you use parts specified by the
manufacturer.
·When service or repairs have been done, perform routine safety checks
to verify that the system is operating correctly.
·Avoid using the system near water, in direct sunlight, or near a heating
device.
·Cover the unit when not in use.

6
http://www.tyan.com
Safety Information
Retain and follow all product safety and operating instructions provided
with your equipment. In the event of a conflict between the instructions in
this guide and the instructions in equipment documentation, follow the
guidelines in the equipment documentation.
Observe all warnings on the product and in the operating instructions. To
reduce the risk of bodily injury, electric shock, fire and damage to the
equipment, observe all precautions included in this guide.
You must become familiar with the safety information in this guide before
you install, operate, or service TYAN products.
Symbols on Equipment
Caution. This symbol indicates a potential hazard.
The potential for injury exists if cautions are not
observed. Consult equipment documentation for
specific details.
Caution. Slide-mounted equipment is not to be
used as a shelf or a work space.
Warning. This symbol indicates the presence of
hazardous energy circuits or electric shock
hazards. Refer all servicing to qualified personnel.
Warning. This symbol indicates the presence of a
hot surface or hot component. If this surface is
contacted, the potential for injury exists.
To reduce risk of injury from a hot component,
allow the surface to cool before touching.

7
http://www.tyan.com
General Precautions
·Follow all caution and warning instructions marked on the equipment and
explained in the accompanying equipment documentation.

Machine Room Environment
 ·Make sure that the area in which you install the system is properly
ventilated and climate-controlled.
·Ensure that the voltage and frequency of your power source match the
voltage and frequency inscribed on the electrical rating label of the
equipment.
·Do not install the system in or near a plenum, air duct, radiator, or heat
register.
·Never use the product in a wet location.
Equipment Chassis
·Do not block or cover the openings to the system.
·Never push objects of any kind through openings in the equipment.
Dangerous voltages might be present.
·Conductive foreign objects can produce a short circuit and cause fire,
electric shock, or damage to your equipment.
·Lift equipment using both hands and with your knees bent.
Equipment Racks
To avoid injury or damage to the equipment:
·Observe local occupational health and safety requirements and guidelines
for manual materials handling.
·Do not attempt to move a rack by yourself; a minimum of two people are
needed to move a rack.
·Do not attempt to move a fully loaded rack. Remove equipment from the
rack before moving it.
·Do not attempt to move a rack on an incline that is greater than 10 degrees
from the horizontal.

8
http://www.tyan.com
·Make sure the rack is properly secured to the floor or ceiling.
·Make sure the stabilizing feet are attached to the rack if it is a single-rack
installation.
·Make sure racks are coupled together if it is a multiple-rack installation.
·Make sure the rack is level and stable before installing an appliance in the
rack.
·Make sure the leveling jacks are extended to the floor.
·Make sure the full weight of the rack rests on the leveling jacks.
·Always load the rack from the bottom up. Load the heaviest component in
the rack first.
·Make sure the rack is level and stable before pulling a component out of the
rack.
·Make sure only one component is extended at a time. A rack might become
unstable if more than one component is extended.
To avoid damage to the equipment:
·The rack width and depth must allow for proper serviceability and cable
management.
·Ensure that there is adequate airflow in the rack. Improper installation or
restricted airflow can damage the equipment.
·The rack cannot have solid or restricted airflow doors. You must use a
mesh door on the front and back of the rack or remove the doors to ensure
adequate air flow to the system.
·If you install the Model in a rack, do not place equipment on top of the unit.
It will cause restricted airflow and might cause damage to the equipment.
·Make sure the product is properly matted with the rails. Products that are
improperly matted with the rails might be unstable.
·Verify that the AC power supply branch circuit that provides power to the
rack is not overloaded. This will reduce the risk of personal injury, fire, or
damage to the equipment. The total rack load should not exceed 80 percent
of the branch circuit rating. Consult the electrical authority having jurisdiction
over your facility wiring and installation requirements.

9
http://www.tyan.com
Equipment Power Cords
·Use only the power cords and power supply units provided with your
system. The system might have one or more power cords.
·Plug the power cord into a grounded (earthed) electrical outlet that is easily
accessible at all times.
·In all European electrical environments, you must ground the Green/Yellow
tab on the power cord. If you do not ground the Green/Yellow tab, it can
cause an electrical shock due to high leakage currents.
·Do not place objects on AC power cords or cables. Arrange them so that no
one might accidentally step on or trip over them.
·Do not pull on a cord or cable. When unplugging from the electrical outlet,
grasp the cord by the plug.
·To reduce the risk of electrical shock, disconnect all power cords before
servicing the appliance.
Equipment Batteries
·The system battery contains lithium manganese dioxide. If the battery pack
is not handled properly, there is risk of fire and burns.
·Do not disassemble, crush, puncture, short external contacts, or dispose of
the battery in fire or water.
·Do not expose the battery to temperatures higher than 60°C (140°F).
·The system battery is not replaceable. If the battery is replaced by an
incorrect type, there is danger of explosion. Replace the battery only with a
spare designated for your product.
·Do not attempt to recharge the battery.
·Dispose of used batteries according to the instructions of the manufacturer.
Do not dispose of batteries with the general household waste. To forward
them to recycling or proper disposal, use the public collection system or return
them to TYAN, your authorized TYAN partner, or their agents.
Equipment Modifications
·Do not make mechanical modifications to the system. TYAN is not
responsible for the regulatory compliance of TYAN equipment that has been
modified.

10
http://www.tyan.com
Equipment Repairs and Servicing
·The installation of internal options and routine maintenance and service of
this product should be performed by individuals who are knowledgeable about
the procedures, precautions, and hazards associated with equipment
containing hazardous energy levels.
·Do not exceed the level of repair specified in the procedures in the product
documentation. Improper repairs can create a safety hazard.
·Allow the product to cool before removing covers and touching internal
components.
·Remove all watches, rings, or loose jewelry when working before removing
covers and touching internal components.
·Do not use conductive tools that could bridge live parts.
·Use gloves when you remove or replace system components; they can
become hot to the touch.
·If the product sustains damage requiring service, disconnect the product
from the AC electrical outlet and refer servicing to an authorized service
provider. Examples of damage requiring service include:
–The power cord, extension cord, or plug has been damaged.
–Liquid has been spilled on the product or an object has fallen into the
product.
–The product has been exposed to rain or water.
–The product has been dropped or damaged.
–The product does not operate normally when you follow the operating
instructions.

http://www.tyan.com
11
Table of Contents
Chapter 1: Overview ........................................................................13
1.1 About the TYAN FT48A-B7070 .............................................. 13
1.2 Product Models....................................................................... 13
1.3 Features.................................................................................. 14
1.4 Standard Parts List ................................................................. 19
1.4.1 Box Contents ....................................................................... 19
1.4.2 Accessories ......................................................................... 20
1.5 System Front View ................................................................... 21
1.5.3 LED Definitions.................................................................... 25
1.5.4 Motherboard (S7070) Layout .............................................. 27
1.5.5 Jumpers/Connectors and Slots ........................................... 28
1.5.6 Block Diagram ..................................................................... 29
1.5.7 Internal View........................................................................ 30
Chapter 2: Setting Up ......................................................................32
2.0.1 Before you Begin ................................................................. 32
2.0.2 Work Area............................................................................ 32
2.0.3 Tools .................................................................................... 32
2.0.4 Precautions.......................................................................... 33
2.1 Installing Motherboard Components ...................................... 34
2.1.1 Removing the Chassis Cover.............................................. 34
2.1.2 Opening the Chassis Front Bezel........................................ 36
2.1.3 Installing the CPU and Heat sink......................................... 37
2.1.4 Installing the Memory .......................................................... 40
2.1.5Installing the PCI-E Cards ................................................... 45
2.2 Installing Hard Drives ............................................................. 49
2.3 Installing DVD Drive ............................................................... 54
2.4 Rack Mounting........................................................................ 59
2.4.1 Installing the Server in a Rack............................................. 59
Chapter 3: Replace Pre-Installed
Components .....................................................................................63
3.1 Introduction ............................................................................. 63
3.2 Disassembly Flowchart........................................................... 63
3.3 Removing the Cover............................................................... 64
3.4 Replacing the System Fan ..................................................... 64
3.5 Replacing the Fan Board........................................................ 65
3.5.1 M1801F77 Fan Board Features .......................................... 67
3.5.2 Fan Board LED Definitions .................................................. 67
3.5.3 M1801F77 Fan Board Connector Pin Definition ................. 68
3.6 Replacing the M1237F48 SATA/SAS Backplane................... 69

http://www.tyan.com
12
3.6.1 M1237F48 SATA/SAS Backplane Features ....................... 70
3.7 Replacing the M1244G70-BP6-8 SATA/SAS Backplane....... 72
3.7.1 M1244G70-BP6-8-B7070 SATA/SAS Backplane Features 73
3.7.2 M1244G70-BP6-8-B7070 Connector Pin Definitions .......... 75
3.8 Replacing the Front Panel Control Board............................... 76
3.8.1 M1018 LED Control Board Features ................................... 78
3.8.2 M1018 LED Control Board Connector Pin Definition .......... 79
3.9 Replacing Power Supply and M7025 PDB............................. 80
3.9.1 Replacing Power Supply ..................................................... 80
3.9.2 Replacing M7025 Power Distribution Board ....................... 81
3.9.3 M7025 Power Distribution Board Features ......................... 84
3.9.4 M7025 PDB Connector Pin Definition ................................. 85
3.10 Replacing S7070 System Board......................................... 87
Appendix I: Cable Connection Tables ...........................................88
Appendix III: FRU Parts Table.........................................................96
Appendix IV: Technical Support.....................................................98

http://www.tyan.com
13
Chapter 1: Overview
1.1 About the TYAN FT48A-B7070
Congratulations on your purchase of the TYAN®FT48A-B7070, a highly optimized
rack-mountable 4U barebones system. The FT48A-B7070 is designed to support
dual Intel®Xeon E5-2600 v3 (Haswell-EP) Series processors, and up to 32GB
RDIMM, 64GB LRDIMM and 128GB LRDIMM 3DS* DDR4 memory for each DIMM
slot. There are 8 channels with 16 DDR4 DIMM slots, providing a rich feature set
and incredible performance. Leveraging advanced technology from Intel®, the
FT48A-B7070 server system is capable of offering scalable 32 and 64-bit
computing, high-bandwidth memory design, and lightning-fast PCI-E Gen2 bus
implementation.
The FT48A-B7070 not only empowers your company in today’s demanding IT
environment but also offers a smooth path for future application usage. The
FT48A-B7070 uses TYAN®’s latest rack-mountable 4U chassis featuring a robust
structure and a solid mechanical enclosure. All of this provides the FT48A-B7070
the power and flexibility to meet the needs of nearly any server application.
1.2 Product Models
Model
MB
HDDs
B7070F48AW16HR
(Channel-W)
S7070WGM2NR
(8) 3.5" / 2.5" HDD trays + (8)
2.5" HDD trays
B7070F48AV4HR-N
(Channel-W)
S7070GM2NR
(4) 3.5" / 2.5" HDD trays

http://www.tyan.com
14
1.3 Features
TYAN FT48AB7070 (B7070F48AW16HR)
System
Form Factor
4U Rackmount
Gross Weight
50 kg
Chassis Model
FT48A
Dimension (D x W x H)
27.5" x 16.8" x 6.9" (700 x 427 x 176mm)
Motherboard
S7070WGM2NR
Board Dimension
EEB, 12"x13" (305x330mm)
Front Panel
Buttons
(1) PWR / (1) RST / (1) NMI / (1) ID
LEDs
(1) PWR / (1) HDD / (2) LAN / (1) ID / (1) Warning
I/O Ports
(2) USB ports
External Drive
Bay
Type / Q'ty
3.5" Hot-Swap + 2.5" Hot-Swap / (8)+(8)
HDD backplane
support
SAS / SATA 6.0Gb/s
Supported HDD
Interface
(8) 3.5" HDDs w/SATA 6Gb/s / (8) 2.5" HDDs
w/SAS 6Gb/s
System Cooling
Configuration
FAN
(3+3) 12cm redundant fans
Power Supply
Type
ERP1U
Efficiency
PFC / 80 plus Platinum
Redundancy
2+1
Input Range
100-127V AC / 200-240V AC
Frequency
50-60 Hertz
Output Watts
1,540W (2 x 770W)
Processor
Supported CPU Series
Intel Xeon Processor E5-2600 v3 series
processors
Socket Type / Q'ty
LGA2011 / (2)
Thermal Design Power
(TDP) wattage
Max up to 160W
System Bus
Up to 9.6/ 8.0/ 6.4 GT/s with Intel QuickPath
Interconnect (QPI) support
Chipset
PCH
Intel C612
Memory
Supported DIMM Qty
(8)+(8) DIMM slots
DIMM Type / Speed
RDIMM DDR4 2133/1866/1600 / LRDIMM DDR4
2133/1600 / LRDIMM 3DS DDR4 2133/1600
Capacity
Up to 512GB RDIMM/ 1,024GB LRDIMM/
2,048GB LRDIMM 3DS *Follow latest Intel DDR4
Memory POR
Memory channel
4 Channels per CPU
Memory voltage
1.2V
Expansion Slots
PCI-E
(2) PCI-E Gen3 x16 slots / (1) PCI-E Gen2 x8 slot
/ (1) PCI-E Gen3 x16 slots (w/ x8/16 link) / (1)

http://www.tyan.com
15
PCI-E Gen3 x8 slots (w/ x8/0 link)
LAN
Port Q'ty
(2) GbE ports (1 port shared with IPMI)
Controller
Intel I350-AM2
Storage
SAS
Connector
(2) Mini-SAS connectors (totally support 8 ports)
Controller
LSI SAS2308
Speed
6.0 Gb/s
RAID
RAID 0/1/1E/10 (LSI Integrated RAID)
SATA
Connector
(1) Mini-SAS (4-ports) + (2) SATA (totally support
6 ports)
Controller
Intel C612
Speed
6.0 Gb/s
RAID
RAID 0/1/10/5 (Intel Matrix RAID)
SSATA
Connector
(4) SATA-III
Controller
Intel C612
Speed
6.0 Gb/s
RAID
RAID 0/1/10/5 (Intel RST) only for 4 SATA
devices
Graphic
Connector type
D-Sub 15-pin
Resolution
Up to 1920x1200
Chipset
Aspeed AST2400
I/O Ports
USB
(6) ports (2 USB2.0 at front, 2 USB2.0 at rear, 2
USB3.0 at rear)
VGA
(1) D-Sub 15-pin port
RJ-45
(2) GbE ports (1 port shared with IPMI)
System
Monitoring
Chipset
Aspeed AST2400
Voltage
Monitors voltage for CPU, memory, chipset &
power supply
Temperature
Monitors temperature for CPU & memory &
system environment
LED
Over temperature warning indicator / Fan & PSU
fail LED indicator
Others
Watchdog timer support
Server
Management
Onboard Chipset
Onboard Aspeed AST2400
AST2400 IPMI Feature
IPMI 2.0 compliant baseboard management
controller (BMC) / Supports storage over IP and
remote platform-flash / USB 2.0 virtual hub
AST2400 iKVM Feature
24-bit high quality video compression / 10/100
Mb/s MAC interface
AST2300 iKVM Feature
10/100 Mb/s MAC interface
BIOS
Brand / ROM size
AMI / 16MB
Feature
User-configurable H/W monitoring / PXE boot
support / SMBIOS 2.5/PnP/Wake on LAN / ACPI
3.0/ACPI sleeping states S4,S5

http://www.tyan.com
16
Operating System
OS supported list
Please refer to our Intel OS supported list.
Regulation
FCC (DoC)
Class A
CE (DoC)
Yes
Operating
Environment
Operating Temp.
10°C ~ 35°C (50°F~ 95°F)
Non-operating Temp.
- 40°C ~ 70°C (-40°F ~ 158°F)
In/Non-operating
Humidity
90%, non-condensing at 35°C
RoHS
RoHS 6/6 Compliant
Yes
Package Contains
Barebone
(1) FT48A-B7070 Barebone*systems will not
display sensor information for the
GPU/Coprocessor cards
Manual
(1) Web User's manual
Installation CD
(1) TYAN installation CD
TYAN FT48AB7070 (B7070F48AV4HR-N)
System
Form Factor
4U Rackmount
Gross Weight
50 kg
Chassis Model
FT48A
Dimension (D x W x H)
27.5" x 16.8" x 6.9" (700 x 427 x 176mm)
Motherboard
S7070GM2NR
Board Dimension
EEB, 12"x13" (305x330mm)
Front Panel
Buttons
(1) PWR / (1) RST / (1) NMI / (1) ID
LEDs
(1) PWR / (1) HDD / (2) LAN / (1) ID / (1) Warning
I/O Ports
(2) USB ports
External Drive
Bay
Type / Q'ty
3.5" Hot-Swap / (4)
HDD backplane
support
SAS / SATA 6.0Gb/s
Supported HDD
Interface
(4) 3.5" HDDs w/SATA 6Gb/s
System Cooling
Configuration
FAN
(3+3) 12cm redundant fans
Power Supply
Type
ERP1U
Efficiency
PFC / 80 plus Platinum
Redundancy
2+1
Input Range
100-127V AC / 200-240V AC
Frequency
50-60 Hertz
Output Watts
1,540W (2 x 770W)
Processor
Supported CPU Series
Intel Xeon Processor E5-2600 v3 series
processors
Socket Type / Q'ty
LGA2011 / (2)
Thermal Design Power
(TDP) wattage
Max up to 160W
System Bus
Up to 9.6/ 8.0/ 6.4 GT/s with Intel QuickPath

http://www.tyan.com
17
Interconnect (QPI) support
Chipset
PCH
Intel C612
Memory
Supported DIMM Qty
(8)+(8) DIMM slots
DIMM Type / Speed
RDIMM DDR4 2133/1866/1600 / LRDIMM DDR4
2133/1600 / LRDIMM 3DS DDR4 2133/1600
Capacity
Up to 512GB RDIMM/ 1,024GB LRDIMM/
2,048GB LRDIMM 3DS *Follow latest Intel DDR4
Memory POR
Memory channel
4 Channels per CPU
Memory voltage
1.2V
Expansion Slots
PCI-E
(2) PCI-E Gen3 x16 slots / (1) PCI-E Gen2 x8
slot / (1) PCI-E Gen3 x16 slots (w/ x8/16 link) /
(1) PCI-E Gen3 x8 slots (w/ x8/0 link)
LAN
Port Q'ty
(2) GbE ports (1 port shared with IPMI)
Controller
Intel I350-AM2
Storage
SATA
Connector
(1) Mini-SAS (4-ports) + (2) SATA (totally support
6 ports)
Controller
Intel C612
Speed
6.0 Gb/s
RAID
RAID 0/1/10/5 (Intel Matrix RAID)
SSATA
Connector
(4) SATA-III
Controller
Intel C612
Speed
6.0 Gb/s
RAID
RAID 0/1/10/5 (Intel RST) only for 4 SATA
devices
Graphic
Connector type
D-Sub 15-pin
Resolution
Up to 1920x1200
Chipset
Aspeed AST2400
I/O Ports
USB
(6) ports (2 USB2.0 at front, 2 USB2.0 at rear, 2
USB3.0 at rear)
VGA
(1) D-Sub 15-pin port
RJ-45
(2) GbE ports (1 port shared with IPMI)
System
Monitoring
Chipset
Aspeed AST2400
Voltage
Monitors voltage for CPU, memory, chipset &
power supply
Temperature
Monitors temperature for CPU & memory &
system environment
LED
Over temperature warning indicator / Fan & PSU
fail LED indicator
Others
Watchdog timer support
Server
Management
Onboard Chipset
Onboard Aspeed AST2400
AST2400 IPMI Feature
IPMI 2.0 compliant baseboard management
controller (BMC) / Supports storage over IP and

http://www.tyan.com
18
remote platform-flash / USB 2.0 virtual hub
AST2400 iKVM Feature
24-bit high quality video compression / 10/100
Mb/s MAC interface
AST2300 iKVM Feature
10/100 Mb/s MAC interface
BIOS
Brand / ROM size
AMI / 16MB
Feature
User-configurable H/W monitoring / PXE boot
support / SMBIOS 2.5/PnP/Wake on LAN / ACPI
3.0/ACPI sleeping states S4,S5
Operating System
OS supported list
Please refer to our Intel OS supported list.
Regulation
FCC (DoC)
Class A
CE (DoC)
Yes
Operating
Environment
Operating Temp.
10°C ~ 35°C (50°F~ 95°F)
Non-operating Temp.
- 40°C ~ 70°C (-40°F ~ 158°F)
In/Non-operating
Humidity
90%, non-condensing at 35°C
RoHS
RoHS 6/6 Compliant
Yes
Package Contains
Barebone
(1) FT48A-B7070 w/NV Tesla-aware FW
Barebone
Manual
(1) Web User's manual
Installation CD
(1) TYAN installation CD

http://www.tyan.com
19
1.4 Standard Parts List
This section describes FT48A-B7070 package contents and accessories.
Open the box carefully and ensure that all components are present and
undamaged. The product should arrive packaged as illustrated below.
1.4.1 Box Contents
Component
Description
4U Rackmount FT48A Chassis
S7070 Motherboard
(3) DELTA DPS-770GB C 770W
Power Supply
(6)120X120X38mm System FAN
(1) M1018Control Board
(Front Panel LED board)
(2) M1237F48-BP6-4-7055,R01
Backplane Board
(1) M1244G70-BP6-8-B7070
Backplane Board
(Only for B7070F48AW16HR /
B7070F48AV16HR)
(1) M7025-PDB-NLS,R02
Power Distribution Board
(1) M1801F77-FB-FT48,R03
Fan Board

http://www.tyan.com
20
1.4.2 Accessories
If any items are missing or appear damaged, contact your retailer or browse to
TYAN’s website for service: http://www.tyan.com
The web site also provides information of other TYAN®products, as well as
FAQs, compatibility lists, BIOS settings, etc.
1 x TYAN®
Motherboard Drive CD
Heatsink x 2
Screw Pack
GPU Power Cable x 2
AC Power Cord 125V
(US) x 2
AC Power Cord 250V
(Europe) x 2
Rail with Bracket
Mounting Ears & Screw Sack
Quick Installation Guide
Addendum for China Use Only
GPU Air Duct for Intel
(Only for B7070F48AV4HR-N)
GPU bracket#2 x 3
(Only for B7070F48AV4HR-N)