TYAN GA80-B7081 Quick start guide

1
http://www.tyan.com
GA80-B7081
Service Engineer’s Manual

2
http://www.tyan.com
PREFACE
Copyright
This publication, including all photographs, illustrations, and software, is
protected under international copyright laws, with all rights reserved.
Neither this manual, nor any material contained herein, may be reproduced
without written consent of manufacturer.
Copyright 2015 MiTAC International Corporation. All rights reserved.
TYAN®is a registered trademark of MiTAC International Corporation.
Version 1.0b
Disclaimer
Information contained in this document is furnished by MiTAC International
Corporation and has been reviewed for accuracy and reliability prior to
printing. MiTAC assumes no liability whatsoever, and disclaims any
express or implied warranty, relating to sale and/or use of TYAN®products
including liability or warranties relating to fitness for a particular purpose or
merchantability. MiTAC retains the right to make changes to produce
descriptions and/or specifications at any time, without notice. In no event
will MiTAC be held liable for any direct or indirect, incidental or
consequential damage, loss of use, loss of data or other malady resulting
from errors or inaccuracies of information contained in this document.
Trademark Recognition
All registered and unregistered trademarks and company names
contained in this manual are property of their respective owners including,
but not limited to the following.
TYAN®is a trademark of MiTAC International Corporation.
Intel®is a trademark of Intel®Corporation.
AMI®, AMIBIOS® and combinations thereof are trademarks of AMI
Technologies.
Microsoft®, Windows®are trademarks of Microsoft Corporation.
IBM®, PC®, AT®and PS/2®are trademarks of IBM Corporation.
Winbond®is a trademark of Winbond Electronics Corporation.

3
http://www.tyan.com
FCC Declaration
Notice for the USA
Compliance Information Statement (Declaration of
Conformity Procedure) DoC FCC Part 15: This
device complies with part 15 of the FCC Rules
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following conditions:
This device must not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Notice for Canada
This Class A digital apparatus complies with Canadian ICES-003. Cet
appareil numérique de la Classe A est conforme àla norme NMB-003
du Canada.
Notice for Europe (CE Mark)
This product is in conformity with the Council
Directive 2004/108/EC.
CAUTION: Lithium battery included with this board. Do not puncture,
mutilate, or dispose of battery in fire. There will be danger of explosion if
battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by manufacturer. Dispose of used battery according
to manufacturer instructions and in accordance with your local
regulations.

4
http://www.tyan.com
About this Manual
This manual provides you with instructions on installing your TYAN
GA80-B7081. This Manual is intended for trained service technician
/personnel with hardware knowledge of personal computers.
This manual consists of the following parts:
Chapter 1: Overview
Provides an introduction to the TYAN GA80-B7081 barebones, standard parts
list, describes the external components, gives a table of key components, and
provides block diagram of the system.
Chapter 2: Setting Up
This chapter covers procedures on installing the processors, memory modules,
hard drivers and other optional parts.
Chapter 3: Replacing the Pre-installed Components
This chapter covers removal and replacement procedures for pre-installed
components.
Chapter 4: Installing the GPU cards
This chapter covers procedures on installing the GPU cards.
Chapter 5: Motherboard Information
This chapter lists the hardware setup procedures that you need to abide by
when installing system components. It includes description of the jumpers and
connectors on the motherboard.
Chapter 6: BIOS Setup
This chapter tells how to change system settings through the BIOS setup menu.
Detailed descriptions of the BIOS parameters are also provided.
Chapter 7: Diagnostics
This chapter introduces some BIOS codes and technical terms to provide better
service for the customers.
Appendix:
This chapter provides the cable connection table, the FRU parts list for reference
of system setup, and technical support in case a problem arises with your system.

5
http://www.tyan.com
Safety and Compliance Information
Before installing and using TYAN GA80-B7081, take note of the following
precautions:
·Read all instructions carefully.
·Do not place the unit on an unstable surface, cart, or stand.
·Do not block the slots and opening on the unit, which are provided for
ventilation.
·Only use the power source indicated on the marking label. If you are not
sure, contact the power company.
·The unit uses a three-wire ground cable, which is equipped with a third
pin to ground the unit and prevent electric shock. Do not defeat the
purpose of this pin. If your outlet does not support this kind of plug,
contact your electrician to replace your obsolete outlet.
·Do not place anything on the power cord. Place the power cord where it
will not be in the way of foot traffic.
·Follow all warnings and cautions in this manual and on the unit case.
·Do not push objects in the ventilation slots as they may touch high
voltage components and result in shock and damage to the
components.
·When replacing parts, ensure that you use parts specified by the
manufacturer.
·When service or repairs have been done, perform routine safety checks
to verify that the system is operating correctly.
·Avoid using the system near water, in direct sunlight, or near a heating
device.
·Cover the unit when not in use.

6
http://www.tyan.com
Safety Information
Retain and follow all product safety and operating instructions
provided with your equipment. In the event of a conflict between the
instructions in this guide and the instructions in equipment
documentation, follow the guidelines in the equipment documentation.
Observe all warnings on the product and in the operating instructions.
To reduce the risk of bodily injury, electric shock, fire and damage to
the equipment, observe all precautions included in this guide.
You must become familiar with the safety information in this guide
before you install, operate, or service TYAN products.
Symbols on Equipment
Warning. This symbol indicates the presence
of hazardous energy circuits or electric shock
hazards. Refer all servicing to qualified
personnel.
Warning. This symbol indicates the presence of a
hot surface or hot component. If this surface is
contacted, the potential for injury exists. To reduce
risk of injury from a hot component, allow the
surface to cool before touching.
Caution. This symbol indicates a potential
hazard. The potential for injury exists if
cautions are not observed. Consult equipment
documentation for specific details.
Caution. Slide-mounted equipment is not to be
used as a shelf or a work space.

7
http://www.tyan.com
General Precautions
·Follow all caution and warning instructions marked on the equipment
and explained in the accompanying equipment documentation.
Machine Room Environment
 ·Make sure that the area in which you install the system is properly
ventilated and climate-controlled.
·Ensure that the voltage and frequency of your power source match the
voltage and frequency inscribed on the electrical rating label of the
equipment.
·Do not install the system in or near a plenum, air duct, radiator, or heat
register.
·Never use the product in a wet location.
Equipment Chassis
·Do not block or cover the openings to the system.
·Never push objects of any kind through openings in the equipment.
Dangerous voltages might be present.
·Conductive foreign objects can produce a short circuit and cause fire,
electric shock, or damage to your equipment.
·Lift equipment using both hands and with your knees bent.
Equipment Racks
To avoid injury or damage to the equipment:
·Observe local occupational health and safety requirements and
guidelines for manual materials handling.
·Do not attempt to move a rack by yourself; a minimum of two people
are needed to move a rack.
·Do not attempt to move a fully loaded rack. Remove equipment from
the rack before moving it.
·Do not attempt to move a rack on an incline that is greater than 10
degrees from the horizontal.
·Make sure the rack is properly secured to the floor or ceiling.

8
http://www.tyan.com
·Make sure the stabilizing feet are attached to the rack if it is a
single-rack installation.
·Make sure racks are coupled together if it is a multiple-rack installation.
·Make sure the rack is level and stable before installing an appliance in
the rack.
·Make sure the leveling jacks are extended to the floor.
·Make sure the full weight of the rack rests on the leveling jacks.
·Always load the rack from the bottom up. Load the heaviest component
in the rack first.
·Make sure the rack is level and stable before pulling a component out
of the rack.
·Make sure only one component is extended at a time. A rack might
become unstable if more than one component is extended.
To avoid damage to the equipment:
·The rack width and depth must allow for proper serviceability and cable
management.
·Ensure that there is adequate airflow in the rack. Improper installation
or restricted airflow can damage the equipment.
·The rack cannot have solid or restricted airflow doors. You must use a
mesh door on the front and back of the rack or remove the doors to
ensure adequate air flow to the system.
·If you install the Model in a rack, do not place equipment on top of the
unit. It will cause restricted airflow and might cause damage to the
equipment.
·Make sure the product is properly matted with the rails. Products that
are improperly matted with the rails might be unstable.
·Verify that the AC power supply branch circuit that provides power to
the rack is not overloaded. This will reduce the risk of personal injury, fire,
or damage to the equipment. The total rack load should not exceed 80
percent of the branch circuit rating. Consult the electrical authority having
jurisdiction over your facility wiring and installation requirements.

9
http://www.tyan.com
Equipment Power Cords
·Use only the power cords and power supply units provided with your
system. The system might have one or more power cords.
·Plug the power cord into a grounded (earthed) electrical outlet that is
easily accessible at all times.
·In all European electrical environments, you must ground the
Green/Yellow tab on the power cord. If you do not ground the
Green/Yellow tab, it can cause an electrical shock due to high leakage
currents.
·Do not place objects on AC power cords or cables. Arrange them so
that no one might accidentally step on or trip over them.
·Do not pull on a cord or cable. When unplugging from the electrical
outlet, grasp the cord by the plug.
·To reduce the risk of electrical shock, disconnect all power cords
before servicing the appliance.
·When use 100V-127VAC input: The system does not support
redundant PSU operation if the total system load exceeds 10A.
Equipment Batteries
·The system battery contains lithium manganese dioxide. If the battery
pack is not handled properly, there is risk of fire and burns.
·Do not disassemble, crush, puncture, short external contacts, or
dispose of the battery in fire or water.
·Do not expose the battery to temperatures higher than 60°C (140°F).
·The system battery is not replaceable. If the battery is replaced by an
incorrect type, there is danger of explosion. Replace the battery only with a
spare designated for your product.
·Do not attempt to recharge the battery.
·Dispose of used batteries according to the instructions of the
manufacturer. Do not dispose of batteries with the general household
waste. To forward them to recycling or proper disposal, use the public
collection system or return them to TYAN, your authorized TYAN partner,
or their agents.

10
http://www.tyan.com
Equipment Modifications
·Do not make mechanical modifications to the system. TYAN is not
responsible for the regulatory compliance of TYAN equipment that has
been modified.
Equipment Repairs and Servicing
·The installation of internal options and routine maintenance and service
of this product should be performed by trained service technicians
/personnel who are knowledgeable about the procedures, precautions,
and hazards associated with equipment containing hazardous energy
levels.
·Do not exceed the level of repair specified in the procedures in the
product documentation. Improper repairs can create a safety hazard.
·Allow the product to cool before removing covers and touching internal
components.
·Remove all watches, rings, or loose jewelry when working before
removing covers and touching internal components.
·Do not use conductive tools that could bridge live parts.
·Use gloves when you remove or replace system components; they can
become hot to the touch.
·If the product sustains damage requiring service, disconnect the
product from the AC electrical outlet and refer servicing to an authorized
service provider. Examples of damage requiring service include:
–The power cord, extension cord, or plug has been damaged.
–Liquid has been spilled on the product or an object has fallen into the
product.
–The product has been exposed to rain or water.
–The product has been dropped or damaged.
–The product does not operate normally when you follow the operating
instructions.

11
http://www.tyan.com
Table of Contents
Chapter 1: Overview........................................................................ 13
1.1 About the TYAN GA80-B7081................................................ 13
1.2Product SKU ........................................................................... 13
1.3 Features.................................................................................. 14
1.4 Standard Parts List ................................................................. 23
1.4.1 Box Contents ................................................................... 23
1.4.2 Accessories ..................................................................... 24
1.5 About the Product ................................................................... 25
1.5.1 System Front View........................................................... 25
1.5.2LED control and HDD LED Definitions ............................ 26
1.5.3System Rear View ........................................................... 28
1.5.4LAN and ID LED Definitions ............................................ 29
1.5.5System top view............................................................... 30
Chapter 2: Setting Up...................................................................... 31
2.0.1 Before you Begin ............................................................. 31
2.0.2 Work Area........................................................................ 31
2.0.3 Tools ................................................................................ 31
2.0.4 Precautions ...................................................................... 32
2.1Installing Motherboard Components....................................... 33
2.1.1 Removing the Chassis Cover .......................................... 33
2.1.2Installing the CPU and Heatsink...................................... 34
2.1.3 Installing the Memory....................................................... 37
2.1.4Installing Hard Drives....................................................... 41
2.1.5 Installing the Add-On Card .............................................. 43
2.2.1 Installing the Server in a Rack ......................................... 45
2.2.2 Installing the Outer Rails to the Rack .............................. 46
2.2.3 Installing the inner Rails to the Chassis........................... 47
2.2.4 Rack mounting the Server ............................................... 48
Chapter 3: Replacing Pre-Installed Components ........................ 50
3.0.1 Introduction .......................................................................... 50
3.0.2 Disassembly Flowchart........................................................ 50
3.1 Removing the Cover ............................................................... 51
3.2 Replacing the Front Panel Board ........................................... 51
3.2.1 M1706G62 Front Panel Board Features ......................... 53
3.2.2 Front Panel Board Connector Pin Definition ................... 53
3.3Replacing the System Fan...................................................... 55
3.4Replacing the HDD Backplane ............................................... 57
3.4.1 M7081G81A-BP6-4 HDD Backplane Features ............... 58

12
http://www.tyan.com
3.4.2 M7081G81A-BP6-4 HDD Connector Pin Definitions....... 59
3.5Replacing PCI-E Riser Cards ................................................. 60
3.5.1 PCIE Riser card Features................................................ 63
3.6 Replacing the Power Supply .................................................. 64
3.7 Removing Motherboard Procedures....................................... 66
3.7.1 Disconnecting All Motherboard Cables ........................... 66
3.7.2 Removing the Motherboard ............................................. 67
Chapter 4: Installing GPU Cards.................................................... 68
4.1 Installing the Intel®Phi GPU card ........................................... 68
Chapter 5: Motherboard Information............................................. 71
5.1 Board Image ........................................................................... 72
5.2 Block Diagram ........................................................................ 73
5.3 Motherboard Mechanical Drawing .......................................... 74
5.4 Board parts, jumpers and connectors..................................... 75
Chapter 6: BIOS Setup.................................................................... 81
6.1 About the BIOS....................................................................... 81
6.2 Main Menu .............................................................................. 83
6.3 Advanced Menu...................................................................... 84
6.4Intel RC Setup ...................................................................... 107
6.4.1 Processor Configuration ................................................ 109
6.4.2 Advanced Power Management Configuration ............... 112
6.4.3 Common RefCode Configuration .................................. 115
6.4.4 QPI Configuration .......................................................... 116
6.4.5 Memory Configuration ................................................... 119
6.4.6 IIO Configuration............................................................ 123
6.4.7 PCH Configuration......................................................... 125
6.4.8Miscellaneous Configuration ......................................... 130
6.4.9 Runtime Error Logging................................................... 131
6.5 Server Management ............................................................. 133
6.6Security................................................................................. 136
6.7 Boot....................................................................................... 137
6.8Save & Exit ........................................................................... 140
Chapter 7: Diagnostics ................................................................. 142
7.1 Flash Utility ........................................................................... 142
7.2 AMIBIOS Post Code (Aptio) ................................................. 143
Appendix I: Fan and Temp Sensors ............................................ 152
Appendix II: Cable Connection Tables........................................ 157
Appendix III: FRU Parts Table...................................................... 158
Appendix IV: Technical Support.................................................. 159

13
http://www.tyan.com
Chapter 1: Overview
1.1 About the TYAN GA80-B7081
Congratulations on your purchase of the TYAN®GA80-B7081, a highly
optimized rack-mountable barebone system. The GA80-B7081 is designed to
support Intel Xeon Processor E5-2600 v3/v4 (Haswell) with Up to 512GB
RDIMM/1,024GB LRDIMM. Leveraging advanced technology from Intel®,
GA80-B7081 server system is capable of offering scalable 32 and 64-bit
computing, high bandwidth memory design, and lightning-fast PCI-E bus
implementation.
The GA80-B7081 not only empowers your company in nowadays IT demand but
also offers a smooth path for future application usage.
TYAN®is also proud to deliver the GA80-B7081 in a version that can support up
to four 2.5‖hot-swap hard drives. The GA80-B7081 uses TYAN®‘s latest chassis
featuring a robust structure and a solid mechanical enclosure. All of this provides
GA80-B7081 the power and flexibility to meet the needs of nowadays server
application.
1.2Product SKU
The system board within the TYAN®Barebone contains different SKUs, which are
defined by the following SKUs:
●B7081G80V4HR-2T-N
●B7081G80V4HR-2T-X
●B7081G80V4HR-N
●B7081G80V4HR-X

14
http://www.tyan.com
1.3 Features
TYAN GA80-B7081 (B7081G80V4HR-2T-N)
System
Form Factor
1U Rackmount
Chassis Model
GA80
Dimension (D x W x
H)
31.50" x 17.32" x 1.73" (800 x 440 x 43.9mm)
Motherboard
S7081GM3NR-2T-N
Front Panel
Buttons
(1) PWR / (1) RST / (1) ID
LEDs
(1) HDD / (2) LAN / (1) ID / (1) IPMI/Warning
I/O Ports
(2) USB ports
External Drive
Bay
Type / Q'ty
2.5" Hot-Swap / (4)
HDD backplane
support
SATA 6Gb/s/ SAS 12Gb/s
System Cooling
Configuration
FAN
(9) 4cm fans
Power Supply
Type
RPSU
Efficiency
PFC / 80 plus Platinum
Redundancy
1+1
Input Range
200-240V AC/9.48A ; 100-127V/12A*
Output Watts
1600 Watts Max. (only for 200-240V AC)
Processor
Supported CPU
Series
Intel Xeon Processor E5-2600 v3/v4 series
processors
Socket Type / Q'ty
LGA2011 / (2)
Thermal Design
Power (TDP)
wattage
Max up to 135W*Please refer to CPU support list
System Bus
Up to 9.6/ 8.0/ 6.4 GT/s with Intel QuickPath
Interconnect (QPI) support
Chipset
PCH
Intel C612
Memory
Supported DIMM
Qty
(8)+(8) DIMM slots
DIMM Type / Speed
RDIMM DDR4 2400/2133/1600 / LRDIMM DDR4
2400/1866 / LRDIMM 3DS DDR4 2400/1866 (*Up
to 2400 speed support only w/E5-2600 v4)
Capacity
Up to 512GB RDIMM/ 1,024GB LRDIMM
Follow latest Intel DDR4 Memory POR
Memory channel
4 Channels per CPU
Memory voltage
1.2V
Expansion
Slots
PCI-E
(1) PCI-E Gen3 x8 slot / (3) PCI-E Gen3 x16 slots
Pre-install TYAN
Riser Card
M7081-R8-1L, PCI-E Gen3 x8 1U riser card
(right) / M7081-R16-1F, PCI-E Gen3 x16 1U riser

15
http://www.tyan.com
card (right) / M7081-L16-1F-1, PCI-E Gen3 x16
1U riser card (left) / M7081-L16-1F-2, PCI-E Gen3
x16 1U riser card (left)
LAN
Port Q'ty
(2) 10GbE ports, (1) GbE port shared with IPMI
Controller
Intel X540-AT2 / Intel I210
Storage
SATA
Connector
(1) Mini-SAS (4-port)
Controller
Intel C612
Speed
6.0 Gb/s
RAID
RAID 0/1/10/5 (Intel RST)
Graphic
Connector type
D-Sub 15-pin
Resolution
Up to 1920x1200
Chipset
Aspeed AST2400
I/O Ports
USB
(2) USB3.0 ports (2 at rear)
COM
(1) DB-9 COM port
VGA
(1) D-Sub 15-pin port
RJ-45
(2) 10GbE + (1) GbE shared with IPMI
Button
ID Button
Others
ID LED
System
Monitoring
Chipset
Aspeed AST2400
Voltage
Monitors voltage for CPU, memory, chipset &
power supply
Temperature
Monitors temperature for CPU & memory &
system environment
LED
Over temperature warning indicator / Fan & PSU
fail LED indicator
Server
Management
Onboard Chipset
Onboard Aspeed AST2400
AST2400 IPMI
Feature
IPMI 2.0 compliant baseboard management
controller (BMC) / Supports storage over IP and
remote platform-flash / USB 2.0 virtual hub
AST2400 iKVM
Feature
24-bit high quality video compression / 10/100
Mb/s MAC interface
BIOS
Brand / ROM size
AMI / 16MB
Feature
User-configurable H/W monitoring /
Auto-configurable of hard disk types / SMBIOS
2.7/PnP/Wake on LAN / PXE boot support / ACPI
3.0/ACPI sleeping states S4,S5
Operating
System
OS supported list
Please refer to our Intel OS supported list.
Regulation
FCC (DoC)
Class A
CE (DoC)
Yes
Operating
Environment
Operating Temp.
10°C ~ 35°C (50°F~ 95°F)
Non-operating
Temp.
- 40°C ~ 70°C (-40°F ~ 158°F)

16
http://www.tyan.com
In/Non-operating
Humidity
90%, non-condensing at 35°C
RoHS
RoHS 6/6
Compliant
Yes
Package
Contains
Barebone
(1) GA80-B7081 w/NV Tesla-aware FW Barebone
Manual
(1) Web User's manual / (1) Quick Installation
Guide
Installation CD
(1) TYAN installation CD
TYAN GA80-B7081 (B7081G80V4HR-2T-X)
System
Form Factor
1U Rackmount
Chassis Model
GA80
Dimension (D x W x
H)
31.50" x 17.32" x 1.73" (800 x 440 x 43.9mm)
Motherboard
S7081GM3NR-2T-N
Front Panel
Buttons
(1) PWR / (1) RST / (1) ID
LEDs
(1) HDD / (2) LAN / (1) ID / (1) IPMI/Warning
I/O Ports
(2) USB ports
External Drive
Bay
Type / Q'ty
2.5" Hot-Swap / (4)
HDD backplane
support
SATA 6Gb/s/ SAS 12Gb/s
System Cooling
Configuration
FAN
(9) 4cm fans
Power Supply
Type
RPSU
Efficiency
PFC / 80 plus Platinum
Redundancy
1+1
Input Range
200-240V AC/9.48A ; 100-127V/12A*
Output Watts
1600 Watts Max. (only for 200-240V AC)
Processor
Supported CPU
Series
Intel Xeon Processor E5-2600 v3/v4 series
processors
Socket Type / Q'ty
LGA2011 / (2)
Thermal Design
Power (TDP)
wattage
Max up to 135W*Please refer to CPU support list
System Bus
Up to 9.6/ 8.0/ 6.4 GT/s with Intel QuickPath
Interconnect (QPI) support
Chipset
PCH
Intel C612
Memory
Supported DIMM
Qty
(8)+(8) DIMM slots
DIMM Type / Speed
RDIMM DDR4 2400/2133/1600 / LRDIMM DDR4
2400/1866 / LRDIMM 3DS DDR4 2400/1866 (*Up
to 2400 speed support only w/E5-2600 v4)
Capacity
Up to 512GB RDIMM/ 1,024GB LRDIMM/

17
http://www.tyan.com
Follow latest Intel DDR4 Memory POR
Memory channel
4 Channels per CPU
Memory voltage
1.2V
Expansion
Slots
PCI-E
(1) PCI-E Gen3 x8 slot / (3) PCI-E Gen3 x16 slots
Pre-install TYAN
Riser Card
M7081-R8-1L, PCI-E Gen3 x8 1U riser card
(right) / M7081-R16-1F, PCI-E Gen3 x16 1U riser
card (right) / M7081-L16-1F-1, PCI-E Gen3 x16
1U riser card (left) / M7081-L16-1F-2, PCI-E Gen3
x16 1U riser card (left)
LAN
Port Q'ty
(2) 10GbE ports, (1) GbE port shared with IPMI
Controller
Intel X540-AT2 / Intel I210
Storage
SATA
Connector
(1) Mini-SAS (4-port)
Controller
Intel C612
Speed
6.0 Gb/s
RAID
RAID 0/1/10/5 (Intel RST)
Graphic
Connector type
D-Sub 15-pin
Resolution
Up to 1920x1200
Chipset
Aspeed AST2400
I/O Ports
USB
(2) USB3.0 ports (2 at rear)
COM
(1) DB-9 COM port
VGA
(1) D-Sub 15-pin port
RJ-45
(2) 10GbE + (1) GbE shared with IPMI
Button
ID Button
Others
ID LED
System
Monitoring
Chipset
Aspeed AST2400
Voltage
Monitors voltage for CPU, memory, chipset &
power supply
Temperature
Monitors temperature for CPU & memory &
system environment
LED
Over temperature warning indicator / Fan & PSU
fail LED indicator
Server
Management
Onboard Chipset
Onboard Aspeed AST2400
AST2400 IPMI
Feature
IPMI 2.0 compliant baseboard management
controller (BMC) / Supports storage over IP and
remote platform-flash / USB 2.0 virtual hub
AST2400 iKVM
Feature
24-bit high quality video compression / 10/100
Mb/s MAC interface
BIOS
Brand / ROM size
AMI / 16MB
Feature
User-configurable H/W monitoring /
Auto-configurable of hard disk types / SMBIOS
2.7/PnP/Wake on LAN / PXE boot support / ACPI
3.0/ACPI sleeping states S4,S5
Operating
OS supported list
Please refer to our Intel OS supported list.

18
http://www.tyan.com
System
Regulation
FCC (DoC)
Class A
CE (DoC)
Yes
Operating
Environment
Operating Temp.
10°C ~ 35°C (50°F~ 95°F)
Non-operating
Temp.
- 40°C ~ 70°C (-40°F ~ 158°F)
In/Non-operating
Humidity
90%, non-condensing at 35°C
RoHS
RoHS 6/6
Compliant
Yes
Package
Contains
Barebone
(1) GA80-B7081 w/Intel Xeon Phi-aware FW
Barebone
Manual
(1) Web User's manual / (1) Quick Installation
Guide
Installation CD
(1) TYAN installation CD
TYAN GA80-B7081 (B7081G80V4HR-N)
System
Form Factor
1U Rackmount
Chassis Model
GA80
Dimension (D x W x
H)
31.50" x 17.32" x 1.73" (800 x 440 x 43.9mm)
Motherboard
S7081GM3NR-N
Front Panel
Buttons
(1) PWR / (1) RST / (1) ID
LEDs
(1) HDD / (2) LAN / (1) ID / (1) IPMI/Warning
I/O Ports
(2) USB ports
External Drive
Bay
Type / Q'ty
2.5" Hot-Swap / (4)
HDD backplane
support
SATA 6Gb/s/ SAS 12Gb/s
System Cooling
Configuration
FAN
(9) 4cm fans
Power Supply
Type
RPSU
Efficiency
PFC / 80 plus Platinum
Redundancy
1+1
Input Range
200-240V AC/9.48A ; 100-127V/12A*
Output Watts
1600 Watts Max. (only for 200-240V AC)
Processor
Supported CPU
Series
Intel Xeon Processor E5-2600 v3/v4 series
processors
Socket Type / Q'ty
LGA2011 / (2)
Thermal Design
Power (TDP)
wattage
Max up to 135W*Please refer to CPU support list
System Bus
Up to 9.6/ 8.0/ 6.4 GT/s with Intel QuickPath
Interconnect (QPI) support

19
http://www.tyan.com
Chipset
PCH
Intel C612
Memory
Supported DIMM
Qty
(8)+(8) DIMM slots
DIMM Type / Speed
RDIMM DDR4 2400/2133/1600 / LRDIMM DDR4
2400/1866 / LRDIMM 3DS DDR4 2400/1866 (*Up
to 2400 speed support only w/E5-2600 v4)
Capacity
Up to 512GB RDIMM/ 1,024GB LRDIMM
Follow latest Intel DDR4 Memory POR
Memory channel
4 Channels per CPU
Memory voltage
1.2V
Expansion Slots
PCI-E
(1) PCI-E Gen3 x8 slot / (3) PCI-E Gen3 x16 slots
Pre-install TYAN
Riser Card
M7081-R8-1L, PCI-E Gen3 x8 1U riser card
(right) / M7081-R16-1F, PCI-E Gen3 x16 1U riser
card (right) / M7081-L16-1F-1, PCI-E Gen3 x16
1U riser card (left) / M7081-L16-1F-2, PCI-E
Gen3 x16 1U riser card (left)
LAN
Port Q'ty
Total (3) ports, (1) shared with IPMI
Controller
Intel I350-BT2 / Intel I210
Storage
SATA
Connector
(1) Mini-SAS (4-port)
Controller
Intel C612
Speed
6.0 Gb/s
RAID
RAID 0/1/10/5 (Intel RST)
Graphic
Connector type
D-Sub 15-pin
Resolution
Up to 1920x1200
Chipset
Aspeed AST2400
I/O Ports
USB
(2) USB3.0 ports (2 at rear)
COM
(1) DB-9 COM port
VGA
(1) D-Sub 15-pin port
RJ-45
(3) GbE ports (1 port shared with IPMI)
Button
ID Button
Others
ID LED
System
Monitoring
Chipset
Aspeed AST2400
Voltage
Monitors voltage for CPU, memory, chipset &
power supply
Temperature
Monitors temperature for CPU & memory &
system environment
LED
Over temperature warning indicator / Fan & PSU
fail LED indicator
Server
Management
Onboard Chipset
Onboard Aspeed AST2400
AST2400 IPMI
Feature
IPMI 2.0 compliant baseboard management
controller (BMC) / Supports storage over IP and
remote platform-flash / USB 2.0 virtual hub
AST2400 iKVM
24-bit high quality video compression / 10/100

20
http://www.tyan.com
Feature
Mb/s MAC interface
BIOS
Brand / ROM size
AMI / 16MB
Feature
User-configurable H/W monitoring /
Auto-configurable of hard disk types / SMBIOS
2.7/PnP/Wake on LAN / PXE boot support / ACPI
3.0/ACPI sleeping states S4,S5
Operating
System
OS supported list
Please refer to our Intel OS supported list.
Regulation
FCC (DoC)
Class A
CE (DoC)
Yes
Operating
Environment
Operating Temp.
10°C ~ 35°C (50°F~ 95°F)
Non-operating
Temp.
- 40°C ~ 70°C (-40°F ~ 158°F)
In/Non-operating
Humidity
90%, non-condensing at 35°C
RoHS
RoHS 6/6 Compliant
Yes
Package
Contains
Barebone
(1) GA80-B7081 w/NV Tesla-aware FW
Barebone
Manual
(1) Web User's manual / (1) Quick Installation
Guide
Installation CD
(1) TYAN installation CD
TYAN GA80-B7081 (B7081G80V4HR-X)
System
Form Factor
1U Rackmount
Chassis Model
GA80
Dimension (D x W x
H)
31.50" x 17.32" x 1.73" (800 x 440 x 43.9mm)
Motherboard
S7081GM3NR-N
Front Panel
Buttons
(1) PWR / (1) RST / (1) ID
LEDs
(1) HDD / (2) LAN / (1) ID / (1) IPMI/Warning
I/O Ports
(2) USB ports
External Drive
Bay
Type / Q'ty
2.5" Hot-Swap / (4)
HDD backplane
support
SATA 6Gb/s/ SAS 12Gb/s
System Cooling
Configuration
FAN
(9) 4cm fans
Power Supply
Type
RPSU
Efficiency
PFC / 80 plus Platinum
Redundancy
1+1
Input Range
200-240V AC/9.48A ; 100-127V/12A*
Output Watts
1600 Watts Max. (only for 200-240V AC)
Processor
Supported CPU
Series
Intel Xeon Processor E5-2600 v3/v4 series
processors