TYSON HaspLock Series User manual

1. Place the HaspLock in
the installation position.
2. Line up the Hinge and
Hinge Plate faces.
3. Draw a pencil line
around the Hinge Plate
and Hasp edges as shown.
Single-Hinge 90 Outer Single-Hinge 90 Inner
Single-Hinge Flat
Double-Hinge 90 Curved
WARRANTY & LIMITATION OF LIABILITY
This TYSON product is warranted to be free from defects in materials and workmanship for a period of
one (1) year from the date of the original purchase. This warranty is for replacement of product only
and TYSON does not accept any responsibility for any direct or consequential damage caused by this
product or its use. This warranty does not cover damage that from results from faulty installation or
usage, alteration or modification of the product or tarnishing of the finish, including colour damage,
due to weather, salt or chemicals. Should any TYSON product not perform satisfactorily to its intended
application then return it to its place of purchase for a replacement. Page 1/3
Made in China for;
TYSON USA LLC
3115 East 12th Street
Los Angeles CA 90023
USA
www.tyson-usa.com

  
 

Preparation
The installation examples of the TYSON HaspLock Single-Hinge and
Double-Hinge models shown in the diagrams are just some of the variations
possible that include flat, inner, outer and curved mounting options. Before
installing, ensure there is sufficient clearance for the hasp to swing
outwards and down or up, as shown on the Drilling Template.
Tools required
Electric or cordless drill, Ø9.5mm (Ø3/8") drill bit for the Hinge and Staple
installation, Ø3.5mm (Ø9/64") drill bit for the Hasp Clip installation, 5mm
Hex Key (supplied) and a No.2 Phillips screwdriver.
Installation
1. Place the Single-Hinge or Double-Hinge HaspLock in the position
that you plan to install it in.
2. Line up the Hinge and Hinge Plate faces as shown.
3. Draw a pencil line around the Hinge Plate and Hasp parts.
4. Fold or cut the Drilling Template on the lines as shown, line
up the edges to the pencil lines then tape the template into position.
5. Centre punch the hole centres in 4 places as shown, drill the
required hole sizes then remove the template.
6. If the Hasp Clip is to be used, then after installation, swing the
HaspLock either up or down and draw a pencil line around the Hasp.
7. Fold or cut the Hasp Clip Drilling Template on the lines shown, line
up the edges to the pencil lines then tape the template into position.
8. Centre punch the hole centres in 2 places as shown, drill the
required hole sizes then remove the template.
Fastening
The mounting screws supplied are Buttonhead M8 x 60mm and suit a 45mm (1 3/4")
frame. For a shorter frame width, cut the screws back to allow for 10-12mm (3/8"-1/2")
of protrusion from the rear of the frame. Add grease to the screws for easier installation
and removal. For deeper frame widths use longer screws and ensure the same
protrusion. For face mounting, use 14G-16G Pan-Head screws with a minimum depth
of 38mm (1 1/2"). For correct operation of the HaspLock, the head thickness of these
screws should not exceed 4mm (5/32").
Lock Cylinder
The lock cylinder supplied is a standard 6-pin key-in-knob style with a
Schlage C keyway. It can be replaced with another similar style of cylinder
by removing the module from the Hasp with a 4mm Hex Key (not supplied).
Maintenance
If required, lubricate the HaspLock parts with graphite powder,
DO NOT use grease or oil.

Drill 9.5mm ( 3/8") in 4 places. Drill smaller holes to suit face
mounted screws
FOLD LINE
FOLD LINE
FOLD LINE
FOLD LINE
FOLD LINE
FOLD LINE
FOLD
LINE
FOLD
LINE
HINGE SIDE STAPLE SIDE
(1 27/64")
36mm
(7/8")
22mm
(1 27/64")
36mm
(7/8")
22mm
(1 19/64")
33mm
DOUBLE-HINGE 246mm (9 11/16")
SINGLE-HINGE 181mm (7 1/8")
(3 5/32")
80mm
(7/8")
22mm
(7/8")
22mm
(1 1/4")
31.50mm
Clearance 27mm (1 1/16")
Page 2/3

    

FOLD LINE
FOLD LINE
FOLD LINE
FOLD LINE
FOLD LINE
FOLD LINE
Drill 3.50mm ( 9/64") in 2 places for the
Hasp Clip mounting.
(45/64")
18mm
(25/32")
20mm
(25/32")
20mm
(59/64")
23.50mm
Page 3/3

     