Tysso VFD-860 Series User manual

VFD-860/880 Series
VFD Customer Display
User's Manual

-1-
Contents
1. Information
2. Installation
3. Interface
4. Demo Software
5. Command List
............................................................... 2
1.1 Standard Package................................................ 2
1.2 Optional Accessories........................................... 2
1.3 Specifications...................................................... 3
................................................................. 4
2.1 RS-232 Connection.............................................. 4
2.2 Pass-through Connection (For VFD-860/880).... 5
.................................................................... 6
3.1 RS-232 Cable-end.............................................. 6
3.2 DC Power Jack................................................... 6
3.3 Interface of Display Panel Side.......................... 7
3.4 Pass-through Cable Pinouts .............................. 8
........................................................ 9
........................................................ 10
5.1 ESC/POS Command List for VFD-860............. 10
5.2 ESC/POS Command List for VFD-880.............. 13

-3--2-
1. Information
1.1 Standard Package
1.2 Optional Accessories
·
·
·
·
·
·
·
·
Display Unit
Support CD
Power Kit
to retrieve power DC 12V from switching power supply
inside the computer.
Switch-Mode Power Supply
Input: AC 100V~240V, 50Hz~60Hz
Output: DC 9 V, 1A
Power adapter
Input: AC 110V, 60Hz
Output: DC 9 V, 1A
Power adapter
Input: AC 230V, 60Hz
Output: DC 9 V, 1A
Optional fixed pole 300mm or 400mm
Pass through cable
1.3 Specifications
Tube Display
Electrical
Physical
Environmental
Customer Display
Display Pattern
Brightness
Character Type
Command Set
Character Size
Character Number
Power Source
Power Consumption
Central Control Unit
Speed
Dimensions (Panel)
Dimensions (Support)
Dimensions (Base)
Tilt Angle
Rotation Angle
Weight
Interface
Color
Operating
Temperature
Storage Temperature
Relative Humidity
Vacuum Fluorescent Display
5 x 7 dot matrix 16 x 15 dot matrix
700 cd/m2
96 alphanumeric Chinese(Big5/GB)/
& 13 international Korean/Japanese
characters
ESC/POS
6.40W x 9.20H mm 6.52W x 9.77H mm
2 x 20
DC 9V~12V (RS-232)
4.5 Watts (RS-232)
CPU 8032 CPU 8031BH
ROM 64K flash ROM ROM 64K flash ROM
32K SRAM 32K SRAM
29MHz 11MHz
224W x 45D x 83H mm
Telescopic pole 270~440mm or
optional fixed pole 300mm or 400mm
187W x 84D x 22H mm
Max. 53
Max. 360
About 0.8Kg
RS-232
Black or beige
0 ~40 (32 ~104 )
-10 ~50 (14 ~122 )
0%~90% RH
¢X
¢X
¢J ¢J ¢K ¢K
¢J ¢J ¢K ¢K
Model VFD-860 VFD-880

-4- -5-
2. Installation
2.1 RS-232 Connection
Step 1: Turn off the computer.
Step 2: Connect the display cable to the RS-232 port of the
computer.
Step 3: Set the connection between the bundled power kit and
the switch power supply inside the computer or
connecting the DC power source by the appropriate
DC power adapter.
Step 4: Turn on the computer. The display will be on and
ready for receiving data.
2.2 Pass-through Connection
Step 1: Turn off the computer, printer and display.
Step 2: Refer to 3.4 Pass-through Cable Pinouts for detailed
information of the cable to make proper connection to
the proper ports on the devices.
Step 3: Turn on the computer. The display will be on and
ready for receiving data.
Select the proper peripheral through command, either
the printer or the display, and all the data transmitted
from the host will be processed by the selected device.
Note:

-6- -7-
3.3 Interface of Display Panel Side
·
·
Specifications
Data Transmission method: Asynchronous Serial
Default protocol: 9600 bps, non-parity,
8 data bits, 1 stop bit
Interface connector (display panel side)
6 pin Male-Header
Pin assignments:
3. Interface
3.1 RS-232 Cable-end
3.2 DC Power Jack
+
GND +9~12VDC/500~1000mA
DSUB-9 Pin Female Connector
2
3
5
7
8
9
1
4
6
TX
RX
GND
CTS
RTS
VCC
Short Connection
9
5
6
1
1
6
TXD
DSR
RXD
DTR
GND
VCC

-9-
-8-
3.4 Pass-through Cable Pinouts
CBL-VFD-PASS 1
CBL-VFD-PASS 2
For printers with ESC commands
For printers without ESC commands
DB9F DB9M DB9M
To:Host To:Printer To:Display
2 (RXD) 2 (TXD)
3 (TXD) 3 (RXD) 3 (RXD)
4 (DTR) 4 (DSR)
5 (GND) 5 (GND) 6 (RXD)
6 (DSR) 6 (DTR)
7 (RTS) 7 (CTS)
8 (CTS) 8 (RTS)
DB9F DB9M DB9M
To:Host To:Printer To:Display
2 (RXD) 2 (TXD)
3 (RXD) 3 (TXD)
3 (TXD) 3 (RXD)
4 (DTR) 4 (DSR)
5 (GND) 5 (GND) 5 (GND)
6 (DSR) 6 (DTR)
7 (RTS) 7 (CTS)
8 (CTS) 8 (CTS)
6 (DTR) 4 (DSR)
To: PC
1800mm
300mm To:Display
To:Printer
DB 9M
DB 9F
DB 9M
4. Demo Software
Connect the display to the COM 1 of the computer. The default
communication parameters of the display are:
COM port: COM 1
Baud rate: 9600
Parity: None
Data bits: 8
Stop bit: 1
Make sure the display is powered on and connected
properly to the computer.
Insert the bundled CD and install the demo software
through the following directories.
VFD-860: Utilities\VFD-660&460\setup.exe
VFD-880: Utilities\VFD-1615\setup.exe
Run the demo software through the directories.
VFD-860: Start\Programs\VFD-660_460
VFD-880: Start\Programs\VFD-1615
Test the software commands, such as Cursor Position,
Screen Display, and Display Mode, by each index.
Close the configuration utility to complete the setup
process.
·
·
·
·
·

-11-
-10-
5. Command List
5.1 ESC/POS Command List for VFD-860
BS 8 Move cursor left
HT 9 Move cursor right
LF 10 Move cursor down
US LF 31 10 Move cursor up
HOM 11 Move cursor to home position
CR 13 Move cursor to left-most
position
US CR 31 13 Move cursor to right-most
position
US B 31 66 Move cursor to bottom position
US $
31 66 n m Move cursor to specified
1 n 20 position
m=1 or 2
CLR 12 Clear display screen
CAN 24 Clear cursor line
ESC= 27 61 n Select peripheral device
0 n 255
ESC @ 27 64 Initialize display
ESC % 27 37 n 1 n 3 Select/cancel user-defined
character set
ESC &
273 8sbm s=1
Define user-defined character
0 n m 126
set
0 a 5 0 p1...
psx a_255
< <
< <
< <
< < <
< < <
<
Command Code Description Function Description
(decimal)
Command Code Description Function Description
(decimal)
ESC ? 27 63 n Cancel user-defined characters
32 n 126
ESC R 27 82 n 0 n 13 Select an international character
set
ESC t
27 116 n 0 n 5,
Select character code table
16, 17, 18, 19,
254, 255
ESC W
27 28 n m
Select/cancel window range
(x1 y x2 t2)
1 n 4
M=0, 1, 48, 49
1 x 1 x2 20
US Md1 31 1 Specify overwrite mode
US Md2 31 2 Specify vertical scroll mode
US Md3 31 3 Specify horizontal scroll mode
US C 31 67 n Select/cancel cursor display
n=0, 1, 48, 49
US E 31 69 n Select/cancel display screen
0 n 255 blinking
US T
31 84 h m
Set and display time counter
1 h 23
1 m 59
US U 31 85 Display time counter
US X 31 88 n 1 n 4 Brightness adjustment
< <
< <
< <
< <
<<<
< <
< <
< <
< <

-13-
-12-
Command Code Description Function Description
(decimal)
US r 31 114 n Select/cancel reverse characters
n=0, 1, 48, 49
US v 31 118 n Status confirmation by DRT
n=0, 1, 48, 49 signal
US @` 31 64 Execute self-test
US : 31 58 Start/end macro definition
US ^
31 94 n m
Execute and quit macro
0 n 255
0 m 255
US.n 31 46 n Select/cancel cursor display
32 n 255
US,n 31 42 n displayable character code
32 n 255 n= a display the code with a dot
US:n
31 59 n displayable character code
32 n 255 n= a display the code with a
semicolon
US#nm 31 35 n Turn the annunciator ( )
1 n 20 1 m 2 ON/OFF
< <
< <
< <
< <
< <
< < < <
¡¿
5.2 ESC/POS Command List for VFD-880
BS 08 Move cursor left
HT 09 Move cursor right
LF 0A Move cursor down
US LF 1F 0A Move cursor up
HOM 0B Move cursor to home position
CR 0D Move cursor to left-most
position
US CR 1F 0D Move cursor to right-most
position
US B 1F 42 Move cursor to bottom position
US $ n m
1F 24 n m Move cursor to specified
1 n(column) 20 position; nth column and mth
m(line)=1 or 2 line
CLR 0C Clear display screen
CAN 18 Clear cursor line
ESC=n 1B 3D n 1 n 3 Select peripheral device
ESC @ 1B 40 Initialize display
US Md1 1F 01 Specify overwrite mode
US Md2 1F 02 Specify vertical scroll mode
US Md3 1F 03 Specify horizontal scroll mode
ESC % n 1B 25 n 1 n 3 Select/cancel user-defined
character set
ESC & 1B 26 s n m s=1,Define user-defined character
s n m 32 n m 126 set
ESC ? N 1B 3F n Cancel user-defined characters
32 n 126
< <
< <
< <
< < <
< <
Command Code Description Function Description
(decimal)

-14-
Command Code Description Function Description
(decimal)
ESC R n 1B 52 n 0 n 13 Select an international character
set
ESC t n 1B 74 n Select character code table
ESC W n m
1B 52 n m
Select/cancel window range
1 n 4
M=0, 1, 48, 49
US C n 1F 43 n Select/cancel cursor display
n=0, 1, 48, 49
US E n 1F 45 n Set display screen blink interval
0 n 255
US T h m
1F 54 h m
Set and display time counter
0 h 23
0 m 59
US U 1F 55 Display time counter
US X n 1F 58 n 1 n 4 Brightness adjustment
US r n 1F 72 n Select/cancel reverse characters
n=0, 1, 48, 49
US v n 1F 76 n Status confirmation by DRT
n=0, 1, 48, 49 signal
US @ 1F 40 Execute self-test
US : 1F 3A Start/end macro definition
US ^ n m
1F 5E n m
Execute and quit macro
0 n 255
0 m 255
< <
< <
< <
< <
< <
< <
< <
< <