ubabub Pod U0400 User manual

INSTRUCTIONS
revised 100720
Crib
Product Code: U0400
Pod
Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.

Pod
Domestic child crib
Instruction manual
Contents
Contents & Hardware 3
Care & Maintenance 4
ABase assembly 8
B Side panel assembly 9
CSide panel base position 10
DEnd panel position 12
ELower mattress position 14
FUpper mattress position 15
GMattress position 16
HUpper end panel position 17
IFinished assembly 18
Congratulations and
thank you for purchasing
an Ubabub product.
With our entire line of
clearly modern nursery
furniture, we are developing
cribs that have the capacity
to convert into a junior
bed and adapt with your
growing child. During the
design and production
of this product we have
selected materials that are
either recyclable or derived
from sustainable practices.
2
PERSONS REQUIRED ASSEMBLY TIME
TOOLS REQUIRED
– PHILLIPS HEAD SCREWDRIVER
– ALLEN KEY (SUPPLIED)

1 x Plastic Base 1 x Mattress Base 2 x Upper Mattress
Support
2 x Feet2 x Acrylic Side
Panel 2 x Lower Curved
End
2 x U-Shaped
Sides 2 x Upper Curved
End
Contents
Hardware
14 x 10mm
bolt
4 x 20mm
bolt
18 x Pan
Head bolt 10 x Locking Cam
6 x 30mm
bolt
10 x Connector Pin
8 x Support Pin 1 x Allen Key
3
12 x 55mm bolt
1 x Mattress

4
WARNING:
Failure to follow these warnings and
the assembly instructions could result
in serious injury or death.
WARNING:
Parents should ensure a safe environment for the
child by checking regularly, before placing the
child in the product, that every component is
properly and securely in place.
Please do NOT remove any wood screws
in the normal disassembly of the crib.
WARNING:
CAUTION: Use ONLY mattress/pad provided
by manufacturer (which must be at least 53 in.
long by 25 in. wide and not more than 5 in. thick).
Please read the Caution and Warning
Statements insert before using your crib.
WARNING: INFANTS CAN
SUFFOCATE
● In gaps between a mattress too small or too thick
and product sides
● On soft bedding
NEVER add a mattress, pillow, comforter, or padding.

5
● The product, including side rails, must be fully erected prior
to use.
● Strings can cause strangulation! Never place items with a
string around a child’s neck such as hood strings or pacifier
cords. Never suspend strings over product or attach strings
to toys.
● Discontinue use of the product when child is able to climb
out or reaches the height of 35in. (90cm).
● Child can become entrapped and die when improvised
netting or covers are placed on top of a product. Never add
such items to confine child in product.
● When child is able to pull to standing position, set mattress/
base to lowest adjustment position and remove bumper
pads, large toys, and other objects that could serve as steps
for climbing out.
● Never place product near a window where cords from blinds
or drapes can strangle a child.
● Use ONLY mattress/pad provided by manufacturer (which
must be at least 53 in. long by 25 in. wide and not more than
5 in. thick).
● Check proper fit of mattress. Should be not more than 5 inches
thick. The maximum gap between mattress and inside of crib
border (or edge) should be no more than 1 inch.
● Always provide the supervision necessary for the continued
safety of your child. When used for playing, never leave
child unattended.
● To reduce the risk of SIDS, pediatricians recommend
healthy infants be placed on their back to sleep, unless
otherwise advised by your physician.
● Never use this product if there are any loose or missing
fasteners, loose joints, broken parts, or torn mesh/ fabric.
Check before assembly and periodically during use. Contact
MILLION DOLLAR BABY CO. for replacement parts. Never
substitute parts.
● Never use plastic shipping bags or other plastic film as
mattress covers not sold and intended for that purpose.
They can cause suffocation.
● Never use a water mattress with this product.
● If refinishing, use a nontoxic finish specified for children’s
products.
Failure to follow these warnings and the
instructions could result in serious injury or death.
WARNING:

6
Please refer to the label (sample below) on the inside face
of the headboard. Record the model/ item number and serial
number of your crib, the name of the store where you made
the purchase, the date of purchase and the wood finish in
the box to the lower right.
WE WILL ASK YOU FOR YOUR SERIAL NUMBER FOR ALL
WARRANTY AND REPLACEMENT PART REQUESTS. PLEASE
REFER TO THE LAST PAGE OF THIS INSTRUCTION SHEET FOR
WARRANTY INFORMATION. KEEP THIS MANUAL FOR FUTURE
REFERENCE.
THIS PRODUCT CONFORMS TO THE
APPLICABLE REGULATIONS OF THE
CONSUMER PRODUCTS SAFETY COMMISSION.
www.themdbfamily.com
CAUTION: ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 27 1/4 INCHES (69CM) BY
51 5/8 INCHES (131CM) WITH A THICKNESS
NOT EXCEEDING 6 INCHES (15CM).
SAMPLE LABEL
Storage:
Care and Cleaning:
• Solid woods exchange moisture with the air adjusting to major
changes in room temperature and humidity. Therefore, it is
best to place your furniture away from heating or air-
conditioning vents.
• Sunlight is not friendly to solid wood furniture and prolonged
direct exposure to harsh sunlight can discolor the finish. Be
careful not to place your furniture in direct sunlight for
extended periods of time. As with all your fine furniture, blot up
spills immediately.
• Do not scratch or chip the finish. Do not use abrasive chemicals
for cleaning. Clean with mild soap on a soft rag. Rinse and dry
thoroughly. If you ever refinish this furniture, be sure to use only
a non-toxic finish specified for children’s products. If you choose
to refinish this furniture, the warranty will be voided.
CAUTION: Use ONLY mattress/pad
provided by manufacturer (which must
be at least 53 in. long by 25 in. wide and
not more than 5 in. thick).
8700 REX RD.
PICO RIVERA, CA 90660

7
IF YOU WOULD LIKE TO ORDER
REPLACEMENT OR MISSING PARTS
PLEASE VISIT US AT:
OR YOU CAN CONTACT US BY MAIL:
We will replace any missing parts at the time
of purchase or any defective item within
a one year period from the date of original
purchase. Please keep your receipt so that
we may process your warranty request. This
warranty only covers new units with original
packaging and ownership, and is not trans-
ferable. It does not cover any used, second-
hand or demo models.
This warranty does not cover any damaged
or defective parts that result from installation
and assembly, normal wear and tear, abuse,
negligence, improper use or alteration to the
finish, design, and hardware. The specific
legal rights of this warranty may vary from
state to state. Some states do not allow any
exclusion or limitation of incidental damages.
Some states do not allow limitation on how
long an implied warranty lasts.
ONE YEAR LIMITED WARRANTY:
Registering your product is even easier than before.
You can register your product on our website at:
www.themdbfamily.com/registrations
WWW.THEMDBFAMILY.COM/SUPPORT
MILLION DOLLAR BABY CO.
8700 REX RD.
PICO RIVERA, CA 90660

ABase assembly
Step 1 Clear floor space.
Step 2 Lay Plastic Base upside down on a flat surface.
Step 3 Place foot plate into recess area as shown in diagram.
Step 4 Screw in four 10mm length bolts to secure base. Please Note: Do not over-
tighten.
Step 5 Repeat Steps 3 & 4 at other end.
Step 6 Have two adults turn base onto it’s feet.
8 x 10mm Bolt
8

Step 1 Clear floor space.
Step 2 Select U-Shaped Side Panel, place flat on ground with recessed edge facing
up.
Step 3 Select an acrylic side panel and with the countersunk holes facing up, place
into U-Shaped Side Panel, aligning bolt holes.
Step 4 Insert five pan head bolts using phillips head screw driver. Please note: Do
not over-tighten.
Step 5 Repeat Steps 1–4 with other side.
BSide panel assembly
x 2
x 10 Pan
Head Bolts Screwdriver
9

CSide panel and
base position
Step 1 Select constructed side panel from section B and ensure side with bolt holes
faces towards the inner of the crib.
Step 2 Rest side on edge of plastic base, aligning bolt holes.
Step 3 Starting with the center hole, using 55mm bolts attach side to base –
finger tighten only.
Step 4 Insert left and right bolts, finger tighten only.
Step 5 Once all three bolts are in place check alignment and tighten with Allen Key
Please Note: Do not over-tighten.
Step 6 Repeat steps 1–5 on other side.
10

11
6 x 55mm bolt

DEnd panels position
Step 1 Insert Support Pins into the side panels as shown in the diagram.
Step 2 Select Lower Curved End. Select five Connecting Pins and install into Lower
Curved End as shown in the diagram using screw driver.
Step 3 Insert two Locking Cams on side panel.
Step 4 Using the edge of the plastic base as a guide, slide Curved End horizontally
until it joins tightly against side panel.
Step 5 Align the Locking Cams and connecting pins on Lower Curved End. Make
sure connecting pins are passing through the Locking Cams. Insert the
Locking Cam nuts. Use screwdriver to turn Locking Cam nuts clockwise until
tightened. (See Fig. D1).
Step 6 Starting with the center hole, using 55mm bolts attach end to base –
finger tighten only.
Step 7 Insert left and right bolts (using 55mm bolts), finger tighten only.
Step 8 Once all three bolts are in place, check alignment and tighten with Allen Key
Please note: Do not over-tighten.
Step 9 Repeat steps 1–8 on other side.
12

4 x
55mm
bolt
8 x
Support
Pin
10 x
Connector
Pin
2 x
55mm
bolt
4 x
Locking
Cam
Fig. D1
Insert the
Locking Cam
nut.
Use screwdriver to turn Locking
Cam nuts clockwise until tight.
Insert the
connecting pins
to the rails.
5.1
5.2
5.3
Insert the
connecting
pins to the side
panel.
13

ELower mattress position
Step 1 Determine if you need your mattress at the upper or lower position.
Step 2 If lower position is required continue to Step 3, if upper position is required
turn to Section F.
Step 3 Select mattress base, using two adults lower base into position. It will rest on
inside edge of Plastic Base.
Step 4 Select 20mm bolts.
Step 5 Align Mattress Base with bolt holes and attach one bolt at each end.
Finger tighten.
Step 6 Install two remaining bolts then tighten all four bolts with Allen Key.
Step 7 Screw in six 10mm length bolts to cover the holes for upper mattress
14
4 x 20mm Bolt 6 x 10mm Bolt
support braces. Please Note: Do not over-tighten.
Step 8 Proceed to Section H.

FUpper mattress position
Step 1 Select one of the two upper mattress support braces.
Step 2 Align upper mattress support to bolt holes in inside of Lower Curved End.
Step 3 Starting with the center hole, use 30mm length bolt to attach, finger tighten.
Step 4 Insert left and right bolts, finger tighten.
Step 5 Check alignment, then using Allen Key tighen bolts. Please Note: Do not
over-tighten.
Step 6 Repeat Steps 1 to 5 with other end.
6 x 30mm Bolt
15

GMattress position
Step 1 Select mattress base, using two adults lower base into position. It will rest on
the upper mattress support brace.
Step 2 Screw in 20mm length bolts to secure base. Please Note: Do not over-tighten.
Step 3 Align mattress base with bolt holes and attach one bolt at each end.
Finger tighten.
Step 4 Install two remaining bolts then tighten all four bolts with Allen Key.
4 x 20mm Bolt
16

HUpper ends position
Step 1 Select Upper Curved End.
Step 2 Align inside recessed edges with acrylic, lower vertically onto Connecting Pins.
Step 3 Using four Pan Head Bolts attach acrylic side to Upper Curved End.
Step 4 Tighten all using screw driver. Please Note: Do not over-tighten.
Step 5 Insert Locking Cams on Upper Curved Ends.
Step 6 Align the Locking Cams and connecting pins. Insert the connecting pins to the
upper curved end. Make sure connecting pins are passing through the Locking
Cams. Insert the Locking Cam nuts. Use screwdriver to turn Locking Cam nuts
clockwise until tight. (See Fig. H1).
Step 7 Repeat Steps 5 & 6 until it is secured.
Step 8 Repeat Steps 1 to 7 with other Upper Curved End.
x 8 Pan
Head Bolts x 6 Locking Cam
Fig. H1
17
Insert the
Locking Cam
nut.
Use screwdriver to turn Locking
Cam nuts clockwise until tight.
6.1
6.2
6.3
Insert the
connecting pins
to the rails.

18
KEEP THIS MANUAL IN A SAFE PLACE FOR
FUTURE REFERENCE.
Recheck all screws and bolts to be sure they are
fastened securely. Do not overtighten.
Before using your crib, please read all cautionary
statements on the insert sheet.
IFinished assembly
Step 1 Clean all surfaces.
Step 2 Install mattress.
18

19
INSTRUCCIONES
revisado 100720
Cuna
Código de producto: U0400
Pod
Lea todas las instrucciones ANTES del ensamblaje y USO del producto.
GUARDE ESTAS INSTRUCCIONES PARA CONSULTARLAS EN EL FUTURO.

Pod
Cuna para bebés de uso
doméstico
Manual de instrucciones
Permítanos extenderle
una felicitación y nuestro
agradecimiento por adquirir un
producto Ubabub.
Al igual que en toda nuestra
moderna línea de muebles
para la habitación de su bebé,
estamos creando cunas
que tengan la capacidad de
convertirse en una cama infantil
y adaptarse a medida que
crece el niño. Durante el diseño
y producción de este producto
hemos seleccionado materiales
reciclables o producidos
mediante un proceso sostenible.
20
TIEMPO DE
ENSAMBLAJE
PERSONAS
REQUERIDAS
MINUTOS
HERRAMIENTAS REQUERIDAS
- DESTORNILLADOR TIPO PHILLIPS
- LLAVE ALLEN (INCLUIDA)
Contenido
Contenido y herramientas 21
Cuidado y mantenimiento 22
AEnsamblaje de la base 26
BEnsamblaje de los paneles
laterales 27
CColocación de los paneles
laterales en la base 28
DColocación de los
paneles de extremos 30
EColocación del colchón
en posición inferior 32
FColocación del colchón
en posición superior 33
GColocación del colchón 34
HColocación de los extremos
superiores 36
IFinalización del ensamblaje 38