ubicquia UbiCell UG CAT-M User manual

© Ubicquia, Inc. All rights reserved. Uncontrolled if printed. Information contained herein is CONFIDENTIAL & PROPRIETARY INFORMATION OF
UBICQUIA, INC., and may not be copied or reproduced in whole or part, nor disseminated to others, without the express written approval of Ubicquia, Inc.
2060 | rev 2 | Client Use Approved
Installation Manual
UbiCell UG CAT-M
UbiCell UG CAT-1

© Ubicquia, Inc. All rights reserved. Uncontrolled if printed. Information contained herein is CONFIDENTIAL &
PROPRIETARY INFORMATION OF UBICQUIA, INC., and may not be copied or reproduced in whole or part, nor
disseminated to others, without the express written approval of Ubicquia, Inc.
2060 | rev2 | Client Use Approved
1
UbiCell Unboxing
UbiCell UG CAT-1
UbiCell UG CAT-M
(Ambient Light
Sensor)

© Ubicquia, Inc. All rights reserved. Uncontrolled if printed. Information contained herein is CONFIDENTIAL &
PROPRIETARY INFORMATION OF UBICQUIA, INC., and may not be copied or reproduced in whole or part, nor
disseminated to others, without the express written approval of Ubicquia, Inc.
2060 | rev2 | Client Use Approved
2
Tools Needed for Installation (not included)
•Glove or other blacked-out material for testing functionality
Safety Information
CAUTION
•Before installing a UbiCell, ensure the UbiCell has an adhesive backed gasket installed on the underside
of the product.
•Before installing a UbiCell, ensure that the top of the unit is free from contact with obstructions
(billboards, tree limbs, electrical wiring, etc.).
•When connecting the UbiCell to a NEMA receptacle, ensure that the prongs are properly aligned with
their corresponding insertion holes.
•Do not remove the UbiCell cover, as this will void the warranty. The UbiCell Lighting Controller is not a
user serviceable item.
•The external NEMA UbiCell is intended only for outside placement on top of a light post fixture. It should
never be installed inside a fixed closure or cabinet.
•The external NEMA UbiCell should not be installed in non-ventilated areas.
•The UbiCell is subject to atmospheric/environmental conditions and its successful operational
performance requires a continuous, clear line-of-sight propagation path with its gateway or access point.
Interference to its line-of-sight propagation path (e.g., atmospheric conditions or physical obstacles) can
adversely impact its operational performance.
•Be overly cautious of electrical safety while making alterations to the UbiCell or the luminaire housing
during installation steps.
WARNING
•Electrical bodily injury or fatality can occur during installation activity if done incorrectly. Before starting
the installation procedures described in this installation guide, power must be turned off at the
installation site.
•The UbiCell must only be connected to power sources using the proper electrical parameters: 100-
480VAC, and 50-60Hz (see Appendixes A-C for proper wiring connectivity).
•Connectors must be free from moisture and debris to avoid damage or poor performance of equipment.
•If the UbiCell has been dropped or damaged, it should not be installed.
•The installation should only be performed by a certified electrician.

© Ubicquia, Inc. All rights reserved. Uncontrolled if printed. Information contained herein is CONFIDENTIAL &
PROPRIETARY INFORMATION OF UBICQUIA, INC., and may not be copied or reproduced in whole or part, nor
disseminated to others, without the express written approval of Ubicquia, Inc.
2060 | rev2 | Client Use Approved
3
Technical Specifications & Dimensions
UbiCell Dimensions
UbiCell Technical Specifications
RECEPTACLE: NEMA 7-PIN
PURPOSE OF CONTROL:
OPERATING CONTROL
CONSTRUCTION OF CONTROL: PLUG-IN - LOCKING TYPE
OPERATING VOLTAGE:
UP TO 506V
IMPULSE VOLTAGE:
4000V
ACTION TYPE: TYPE 1
POLLUTION DEGREE*:
3
STANDARD WARRANTY: 5 YEARS
RATING:
OUTDOOR/IP66 Enclosure
CERTIFICATIONSᶧ:
UL 60730
FCC ID: XMR202008EG91NAXD (QUECTEL
Model: EG91)
FCC ID: XMR2020BG95M2 (QUECTEL Model:
BG95)
*
Pollution Degrees Explained:
Pollution Degree 1
No pollution or only dry, non-conductive pollution occurs. The pollution has no influence.
Pollution Degree 2
Only non-conductive pollution occurs except that occasionally a temporary conductivity caused by condensation is to be
expected.
Pollution Degree 3
Conductive pollution occurs or dry non-conductive pollution occurs which becomes conductive due to condensation which is to
be expected.
Pollution Degree 4
Continuous conductivity occurs due to conductive dust, rain or wet conditions.
ᶧNote: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Changes or modifications not expressly approved by Ubicquia could void the user's authority to operate the equipment.

© Ubicquia, Inc. All rights reserved. Uncontrolled if printed. Information contained herein is CONFIDENTIAL &
PROPRIETARY INFORMATION OF UBICQUIA, INC., and may not be copied or reproduced in whole or part, nor
disseminated to others, without the express written approval of Ubicquia, Inc.
2060 | rev2 | Client Use Approved
4
Installing the UbiCell
For a more detailed demonstration of
UbiCell installation, watch the UbiCell
Installation Video.
STEP 1 Check NEMA Receptacle
Check that all contacts on the NEMA
receptacle are clean. Check that the
NEMA receptacle does not rotate. If
the receptacle rotates, ensure it is
locked in place before installing.
NOTE: If the receptacle cannot be
locked in place, then it must be held in
place during UbiCell installation.
STEP 2 NEMA Connector Options
Decide which NEMA option diagram
is applicable to the unit and install.
NOTE: See page 6 for NEMA connector
options.
STEP 3 Install the UbiCell
Insert the UbiCell into the NEMA
socket and apply downward
pressure while turning clockwise
about 15 degrees until rotation
completely stops.
NOTE: Optimal communication can be
achieved with a 10ft / 3m minimum
obstruction clearance around the
device.
NOTE: Watch the NEMA Connector
Types video for a demonstration on
preparing the NEMA receptacle for
installation.
~
10 lbs
~ 15°

© Ubicquia, Inc. All rights reserved. Uncontrolled if printed. Information contained herein is CONFIDENTIAL &
PROPRIETARY INFORMATION OF UBICQUIA, INC., and may not be copied or reproduced in whole or part, nor
disseminated to others, without the express written approval of Ubicquia, Inc.
2060 | rev2 | Client Use Approved
5
STEP 4 Vertical Pull Test
Lift up vertically on the UbiCell to
confirm that the hooks are fully
engaged.
STEP 5 Dimming Test
When correctly installed, the UbiCell
should follow the following flash
patterns based on expected
functionality:
If the luminaire supports dimming
functionality, there will be 3 flashes
(on/off) for one second each. If
dimming is not available, there will
be no flashes.
If the expected results are not
achieved, check the line power. If
power is confirmed, perform a second
vertical pull test to validate that the
pins were properly rotated into the
sockets in Step 3. If proper
installation is confirmed, then mark
the UbiCell for return and install a
new UbiCell.
STEP 6 Glove Test
Cover the UbiCell or ALS entirely
with a glove or other blacked-out
material to trigger photocell and turn
on the lamp.
If the glove test fails, check the line
power. If power is confirmed,
perform a second vertical pull test to
validate that the pins were properly
rotated into the sockets in Step 3. If
proper installation is confirmed, then
mark the failed UbiCell for return and
install a new UbiCell.

© Ubicquia, Inc. All rights reserved. Uncontrolled if printed. Information contained herein is CONFIDENTIAL &
PROPRIETARY INFORMATION OF UBICQUIA, INC., and may not be copied or reproduced in whole or part, nor
disseminated to others, without the express written approval of Ubicquia, Inc.
2060 | rev2 | Client Use Approved
7
NEMA Connector Options
DALI or PWM (0-10V) Auto select with option for DALI / External Sensors / UbiSmart
AQM use
DALI or PWM Auto select with option for Analog Input 0-10V
NOTE: Pins 6 & 7 of the NEMA ANSI C136.41 twist-lock photocell connector must never be plugged into a connection
other than the DALI bus specific to Ubicquia use for external sensors; that includes removing any connections from the
luminaire that may have come pre-made, as any non-DALI standard connections could cause damage to the unit or the
luminaire. As reference: Pins 6 & 7 are typically wired in colors brown and orange.
UBICELL
UBICELL