Ubiquiti UniFi USP-Plug User manual

USP-Plug
LED
Package Contents
System Requirements
UniFi Network Controller software v5.12.46 or newer, available at:
ui.com/download/uni
(1) UniFi Access Point or Dream Machine for the USP-Plug to connect to
iOS or Android™ mobile device with UniFi Network App installed
Hardware Overview
Slowly Flashing Ready for setup, waiting to be paired
Double Pulse Flashing Connecting to Wi-Fi
Steady Blue (Always On) Powered on, connected to Wi-Fi
USP-Plug Quick Start Guide

Button
Off Powered off, not plugged in
Power Press and release the Button to toggle power on or off
Factory Reset Press and hold the Button for ve seconds or until the
LED starts ashing
Hardware Installation
1.
2.
3. Wait for the LED on the Button to start ashing blue, and then proceed to “Adopting
the USP-Plug” .
Adopting the USP-Plug
You have the following options:
“Using the UniFi Network App (Recommended)”
“Using the UniFi Network Software”
USP-Plug Quick Start Guide

Using the UniFi Network App (Recommended)
1. 
2.
3.
USP-Plug Quick Start Guide

4. Follow the on-screen instructions.
Using the UniFi Network Software
1. From the UniFi Network Controller dashboard, click Devices in the left menu bar.
2. On the Devices screen, locate the USP-Plug in the list of devices under the Model
column. To adopt the USP-Plug, click Adopt.
USP-Plug Quick Start Guide

Specications
USP-Plug
Dimensions ø51 x48 mm (ø1.97 x 1.89")
Weight 47 g (1.66 oz)
Max. Power Consumption 1100W for 110VAC
Power Method AC Input
Power Supply AC/DC Embedded
Supported Voltage Range 100 - 240VAC, 50/60 Hz, Max. 10A
Networking Interface 802.11 b/g/n Wi-Fi
Button Power/Reset with Integrated LED
Operating Frequency 2.4 GHz
Max. TX Power 16.9 dBm (0.05W)
Wi-Fi Standards 802.11 b/g/n
Wireless Security WPA2-PSK AES/TKIP
Operating Temperature 0 to 40° C (32 to 104° F)
Operating Humidity 10 to 90% Noncondensing
Certications FCC, IC
Safety Notices
1. Read, follow, and keep these instructions.
USP-Plug Quick Start Guide

2. Heed all warnings.
3. Only use attachments/accessories specied by the manufacturer.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements indicated on
the manufacturer’s label. Connection to a different power source than those specied may result in
improper operation, damage to the equipment or pose a re hazard if the limitations are not
followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a
qualied service technician.
Limited Warranty
ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and,
where applicable, specify arbitration instead of jury trials or class actions.
Compliance
FCC
Changes or modications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
USP-Plug Quick Start Guide

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This radio transmitter (FCC ID: SWX-USP1) has been approved by FCC.
ISED Canada
CAN ICES-3(B)/NMB-3(B)
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
This radio transmitter (IC: 6545A-USP1) has been approved by ISED Canada.
CAN ICES-3(B)/NMB-3(B)
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
1. l’appareil ne doit pas produire de brouillage;
2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Le présent émetteur radio (IC : 6545A-USP1) a été approuvé par ISDE Canada.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the
radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
AVIS IMPORTANT :
Déclaration sur l’exposition aux rayonnements :
Cet équipement est conforme aux limites prévues pour l’exposition aux rayonnements dans un
environnement non contrôlé.
Lors de l’installation et de la mise en fonctionnement de l’équipement, assurez-vous qu’il y ait une
distance minimale de 20 cm entre l’élément rayonnant et vous.
Cet émetteur ne doit être installé à proximité d’aucune autre antenne ni d’aucun autre émetteur, et
ne doit être utilisé conjointement à aucun autre de ces appareils.
USP-Plug Quick Start Guide

Declaration of Conformity
Online Resources
© 2020 Ubiquiti Inc. All rights reserved.
USP-Plug Quick Start Guide