Ubiquiti UniFi Protect ViewPort UFP-VIEWPORT User manual

UniFi Protect ViewPort Mounting Bracket Double-Sided Tape
HDMI Cable M6 Screw M8 Screw
Drywall Screws (Qty. 2) Screw Anchors (Qty. 2)
Package Contents
System Requirements
UniFi Protect software v1.13 or above, available at ui.com/downloads/uni
Installation Requirements
Phillips screwdriver
UFP-VIEWPORT Quick Start Guide

Power/Status LED
Drill and 6 mm (1/4") bit for drywall anchors
Drill and 6 mm (1/4") bit or 8 mm bit (5/16") for screws
Shielded Category 5 (or above) cabling with drain wire should be used for all wired
Ethernet connections and should be grounded through the AC ground of the PoE.
Hardware Overview
Solid White Ready for conguration.
UFP-VIEWPORT Quick Start Guide

Main Port
HDMI Port
Secondary Port
Reset Button
Blue The device has been adopted by the UniFi Protect
Controller.
Alternating Blue/White The device is booting up.
This 10/100/1000 RJ45 port connects to an 802.3af switch for PoE power and data.
This HDMI port connects to a TV or monitor with an HDMI cable. It supports 1080p and
4K displays.
This 10/100/1000 RJ45 port functions as a data passthrough port.
Restore to Factory Defaults Press and hold the Reset button for 5 seconds while the
device is powered on. Release the Reset button when the LED turns off.
Hardware Installation
Mounting the UniFi Protect ViewPort is optional; it allows the device to be installed in an
inconspicuous and safe location. You have three options for mounting:
Wall Mount Mount the ViewPort onto a drywall surface.
TV VESA Mount Mount the ViewPort to the back of your TV/monitor using the available
VESA mounting hole(s).
TV Surface Mount Attach the ViewPort to the TV/monitor or other surface using the
included double-sided tape.
Wall Mount
1.
UFP-VIEWPORT Quick Start Guide

2.
UFP-VIEWPORT Quick Start Guide

3.
UFP-VIEWPORT Quick Start Guide

4.
UFP-VIEWPORT Quick Start Guide

5.
UFP-VIEWPORT Quick Start Guide

TV VESA Mount
You can use this option if your TV or monitor is equipped with a VESA mount that uses M6
or M8 screws.
1. 
Optional
(for permanent mounting)
UFP-VIEWPORT Quick Start Guide

OR
M8 Screw M6 Screw
2. 
OR
UFP-VIEWPORT Quick Start Guide

M8 Screw M6 Screw
3.
UFP-VIEWPORT Quick Start Guide

TV Surface Mount
1.
2.
3.
UFP-VIEWPORT Quick Start Guide

4.
UFP-VIEWPORT Quick Start Guide

Connecting the ViewPort
1.
2. 
WARNING: The switch port must comply with the power specications listed in
“Specications” .
UFP-VIEWPORT Quick Start Guide

Note: The PoE switch must be connected to the same LAN or VLAN as the UniFi
Protect controller.
3.
UFP-VIEWPORT Quick Start Guide

4. Follow the instructions on the TV or monitor. (If nothing is displayed, check the power
source to the device.)
UFP-VIEWPORT Quick Start Guide

5. Log in to UniFi Protect. Enter the UniFi Protect username and password. Then click
Submit.
6. When UniFi Protect detects the ViewPort, click Add Device.
Specications
UFP-VIEWPORT
Dimensions (With TV Mount) 156.9 x 52 x 37.35 mm (6.18 x 2.0 x 1.47")
UFP-VIEWPORT Quick Start Guide

UFP-VIEWPORT
Weight
Without TV Mount 230 g (8.11oz)
With TV Mount 252 g (8.89 oz)
Enclosure Polycarbonate
Networking Interface 10/100/1000 Ethernet Port
Management Interface UniFi Protect Controller
Max. Power Consumption 9.5W
Power Method 802.3af PoE
Button Reset/Factory Reset
LED Power/Status
ESD/EMP Protection Air: ± 8kV, Contact: ± 4kV
Operating Temperature 0 to 40° C (32 to 104° F)
Operating Humidity 20 to 80% Noncondensing
Certications CE, FCC, IC
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specied by the manufacturer.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements indicated on
the manufacturer’s label. Connection to a different power source than those specied may result in
improper operation, damage to the equipment or pose a re hazard if the limitations are not
followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a
qualied service technician.
Limited Warranty
ui.com/support/warranty
UFP-VIEWPORT Quick Start Guide

The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and,
where applicable, specify arbitration instead of jury trials or class actions.
Compliance
FCC
Changes or modications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This radio transmitter (FCC ID: SWX-UFPVP) has been approved by FCC.
ISED Canada
CAN ICES-3(B)/NMB-3(B)
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
This radio transmitter (IC: 6545A-UFPVP) has been approved by ISED Canada.
CAN ICES-3(B)/NMB-3(B)
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
1. l’appareil ne doit pas produire de brouillage;
UFP-VIEWPORT Quick Start Guide

2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Le présent émetteur radio (IC : 6545A-UFPVP) a été approuvé par ISDE Canada.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the
radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
AVIS IMPORTANT :
Déclaration sur l’exposition aux rayonnements :
Cet équipement est conforme aux limites prévues pour l’exposition aux rayonnements dans un
environnement non contrôlé.
Lors de l’installation et de la mise en fonctionnement de l’équipement, assurez-vous qu’il y ait une
distance minimale de 20 cm entre l’élément rayonnant et vous.
Cet émetteur ne doit être installé à proximité d’aucune autre antenne ni d’aucun autre émetteur, et
ne doit être utilisé conjointement à aucun autre de ces appareils.
Australia and New Zealand
Brazil
Nota: Este equipamento não tem direito à proteção contra interferência prejudicial e não
pode causar interferência em sistemas devidamente autorizados.
CE Marking
CE marking on this product represents the product is in compliance with all directives that are
applicable to it.
Country List
AT BE BG CY CZ DE DK EE EL ES FI FR HR HU
IE IT LV LT LU MT NL PL PT RO SE SI SK UK
UFP-VIEWPORT Quick Start Guide

BFWA (Broadband Fixed Wireless Access) members noted in blue
Note: This device meets Max. TX power limit per ETSI regulations.
WEEE Compliance Statement
Declaration of Conformity
Online Resources
© 2020 Ubiquiti Inc. All rights reserved.
UFP-VIEWPORT Quick Start Guide