Ubiquiti UVC--G4--BULLET User manual

Camera Cable Gland Screw Anchors (Qty. 2)
Self-Tapping Screws (Qty. 2) Pole Mount Bracket Machine Screws (Qty. 2)
Package Contents
Installation Requirements
Shielded Category 5 (or above) cabling should be used for all wired Ethernet
connections and should be grounded through the AC ground of the PoE.
We recommend that you protect your networks from harmful outdoor environments
and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti.
For more details, visit: ui.com/toughcable
Hardware Overview
UVC-G4-BULLET Quick Start Guide

Ethernet Port
Reset Button
Gigabit RJ45 port connects to an 802.3af PoE switch for PoE power and data.
To reset to factory defaults, press and hold the Reset button for more than 10 seconds
while the camera is powered on.
Hardware Installation
Ceiling Mount
UVC-G4-BULLET Quick Start Guide

Wall Mount
UVC-G4-BULLET Quick Start Guide

UVC-G4-BULLET Quick Start Guide

1.
2.
UVC-G4-BULLET Quick Start Guide

Note: For outdoor installations, position the Cable Slot downward.
3.
UVC-G4-BULLET Quick Start Guide

4.
UVC-G4-BULLET Quick Start Guide

5. 
UVC-G4-BULLET Quick Start Guide

OR
UVC-G4-BULLET Quick Start Guide

IMPORTANT: If you are installing your camera outdoors, create a drip loop for
the cable below the camera to prevent water ingress.
6.
UVC-G4-BULLET Quick Start Guide

7.
8.
UVC-G4-BULLET Quick Start Guide

IMPORTANT: For proper weather sealing, the Cable Gland must fit securely
within the Adjustable Base when the camera is mounted. Ensure that the Cable
Gland is securely seated during installation and cable routing.
9.
10.
UVC-G4-BULLET Quick Start Guide

Pole Mount
1.
2.
3.
UVC-G4-BULLET Quick Start Guide

4.
5.
UVC-G4-BULLET Quick Start Guide

6.
7.
UVC-G4-BULLET Quick Start Guide

IMPORTANT: Ensure that the Cable Gland is securely seated during installation
and cable routing.
8.
9.
UVC-G4-BULLET Quick Start Guide

Connecting to a PoE Switch
UVC-G4-BULLET Quick Start Guide

Setting Up UniFi Protect via App
Launch the UniFi Protect app and follow the on-screen instructions to complete setup.
Adjusting the Camera View
1.
2.
UVC-G4-BULLET Quick Start Guide

Specifications
UVC-G4-BULLET
Dimensions Ø 75 x 140 mm (Ø 2.95 x 5.51")
Weight 458 g (1 lb)
Enclosure Injection-Molded Polycarbonate and
Die-Cast Aluminum
Networking Interface (1) 10/100/1000 Ethernet Port
Viewing Angle 86° (H), 60° (V), 111° (D)
Night Mode IR LEDs with Mechanical IR Cut Filter
Video Compression H.264
Resolution (4MP) 2688 x 1520
Maximum Frame Rate 24 FPS
Image Settings Brightness, Contrast, Sharpness, Saturation, Noise
Reduction, 50/60 Hz
Processor Ambarella S5L55m
Memory 512 MB DDR3L
Management Interface UniFi Protect
Microphone Yes
Max. Power Consumption 4W
Power Method 802.3af
Power Supply 802.3af PoE Switch
Buttons Factory Reset Button
UVC-G4-BULLET Quick Start Guide

UVC-G4-BULLET
Mounting Wall/Ceiling/Pole (Kits Included)
Operating Temperature -20 to 40° C
(-4 to 104° F)
Operating Humidity 0 to 90% Noncondensing
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Hot surface. Do not touch.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements indicated on
the manufacturer’s label. Connection to a different power source than those specified may result in
improper operation, damage to the equipment or pose a fire hazard if the limitations are not
followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a
qualified service technician.
Limited Warranty
ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and,
where applicable, specify arbitration instead of jury trials or class actions.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions.
UVC-G4-BULLET Quick Start Guide