Ubiquiti UVC-G3-BULLET User manual

Camera Cable Gland Screw Anchors (Qty. 2)
Self-Tapping Screws (Qty. 2) Pole Mount Bracket Machine Screws (Qty. 2)
Package Contents
Installation Requirements
Shielded Category 5 (or above) cabling should be used for all wired Ethernet
connections and should be grounded through the AC ground of the PoE.
We recommend that you protect your networks from harmful outdoor
environments and destructive ESD events with industrial-grade, shielded Ethernet
cable from Ubiquiti. For more details, visit ui.com/toughcable
Hardware Overview
UVC-G3-BULLET Quick Start Guide

Ethernet Port
Reset Button
10/100 RJ45 port connects to an 802.3af PoE switch for PoE power and data.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds while the camera is powered on.
Hardware Installation
Wall/Ceiling Mount
1.
UVC-G3-BULLET Quick Start Guide

2.
3.
UVC-G3-BULLET Quick Start Guide

4.
5. 
UVC-G3-BULLET Quick Start Guide

OR
6.
UVC-G3-BULLET Quick Start Guide

7.
8.
UVC-G3-BULLET Quick Start Guide

9.
Pole Mount
1.
2.
UVC-G3-BULLET Quick Start Guide

3.
4.
UVC-G3-BULLET Quick Start Guide

5.
Connecting Power
UVC-G3-BULLET Quick Start Guide

UniFi Protect Mobile App
Launch the UniFi Protect Mobile App and follow the on-screen instructions to
complete setup.
Adjusting the Camera View
1.
UVC-G3-BULLET Quick Start Guide

2.
Specifications
UVC-G3-BULLET
Dimensions Ø 75 x 140 mm
(Ø 2.95 x 5.51")
Weight 300 g
(10.58 oz)
Enclosure Injection-Molded Polycarbonate and
Die-Cast Aluminum
Networking Interface (1) 10/100 Ethernet Port
Sensor 1/3" 4-Megapixel HDR Sensor
Lens EFL 3.6 mm, f/1.8
Viewing Angle
Before Lens Correction 85° (H), 44.8° (V), 98.1° (D)
After Lens Correction 72° (H), 42.9° (V), 80.4° (D)
Night Mode IR LEDs with Mechanical IR Cut Filter
Video Compression H.264
UVC-G3-BULLET Quick Start Guide

UVC-G3-BULLET
Resolution 1080p Full HD (1920 x 1080)
Maximum Frame Rate 30 FPS
Image Settings Brightness, Contrast, Sharpness, Saturation, Noise
Reduction, 50/60 Hz
Processor Ambarella S2L
Memory 512 MB DDR3L
Management Interface UniFi Protect
Microphone Yes
Max. Power Consumption 4W
Power Method 802.3af or 24V Passive PoE
Power Supply 802.3af PoE Switch
Buttons Factory Reset Button
Mounting Wall/Ceiling (Kits Included)
Pole (Kit Not Included)
Operating Temperature -20 to 50° C
(-4 to 122° F)
Operating Humidity 20 to 90% Noncondensing
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Hot surface. Do not touch.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote
risk of electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements
indicated on the manufacturer’s label. Connection to a different power source than those
specified may result in improper operation, damage to the equipment or pose a fire hazard if
the limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided
only by a qualified service technician.
UVC-G3-BULLET Quick Start Guide

Limited Warranty
ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an individual basis,
and, where applicable, specify arbitration instead of jury trials or class actions.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
ISED Canada
CAN ICES-3(A)/NMB-3(A)
Australia and New Zealand
Warning: This equipment is compliant with Class A of CISPR 32. In a residential
environment this equipment may cause radio interference.
CE Marking
CE marking on this product represents the product is in compliance with all directives that are
applicable to it.
WEEE Compliance Statement
Declaration of Conformity
UVC-G3-BULLET Quick Start Guide

Online Resources
© 2022 Ubiquiti Inc. All rights reserved.
UVC-G3-BULLET Quick Start Guide