Ubiquiti UF-LOCO User manual

System Requirements
UF-LOCO Quick Start Guide
Included only in the single package of the UF-LOCO.
wall mount bracket
power adapter
Screws (qty: 4)
Micro-USB* (5 V, 1 A)
UFiber loco
*
Screw plugs (qty: 4)
Linux, Mac OS X o Microsoft Windows 7/8/10
ubnt.link/UFiber-GPON-Getting-Started
ubnt.link/Designing-a-GPON-Network
To learn more about how to configure UFiber devices for the first time to allow the
Optical Network Unit (ONU) LAN ports to provide
Designing your first deployment of a GPON network requires specific planning and
knowledge. For more information on designing and installing a GPON network, including
important considerations and best practices, see:
Web browser: Google Chrome (other browsers may have limited functionality)
Package content
Before starting
Machine Translated by Google

Reset button
Puerto PON
The Reset button has two functions for the UF-LOCO:
The GPON SC/APC port supports 2.488 Gbps downstream and 1.244 Gbps upstream
WAN connections.
connectivity, see: ubnt.link/UFiber-Initial-Configuration
UF-LOCO Quick Start Guide
Reset – Quickly press and release the Reset button. All three signal LEDs will flash amber.
power port
Restore Factory Default Settings: Press and hold the Reset button for more than five seconds.
hardware description
Machine Translated by Google

UF-LOCO Quick Start Guide The
Micro-USB power adapter connects to this port to supply power.
ÿ -11 dBm
LED signal indicators
Signal strength: too low
ethernet power
disabled Start
The RJ45 Ethernet LAN port supports 10/100/1000 Mbps connections and 24V passive PoE to
power the device.
Signal strength: low
< -28 dBm
Check the quality of the fiber connection and calculate the
total optical loss of the optical splitters.
LED the Ethernet
ÿ -28 dBm
Signal strength: too strong
ÿ -8 dBm
disabled
Signal strength: good
Add an optical splitter or a 5 or
10 dB optical attenuator.
ÿ -25 dBm
No signal
No ethernet connection
White
Signal strength: strong
With ethernet connection
Machine Translated by Google

Power LEDs
Switched on
The UF-LOCO has not been authorized or it
cannot communicate with the OLT. Check
passwords and OLT settings.
White
no authority
1.
Off
Check the fiber cables and connectors and
UF-LOCO Quick Start Guide make sure the OLT is
working properly.
disabled
hardware installation
wall mount
Machine Translated by Google

UF-LOCO Quick Start Guide
2.
Machine Translated by Google

UF-LOCO Quick Start Guide
3.
Machine Translated by Google

UF-LOCO Quick Start Guide
4.
Machine Translated by Google

UF-LOCO Quick Start Guide
fiber connection
WARNING: DO NOT connect the device directly to a UFiber GPON module
(UF-GP-B+ or UF-GP-C+). Doing so will damage the optics of the device.
Make sure that the signal level received by the device never exceeds -8 dBm.
Use a UFiber PLC splitter to add attenuation as needed.
WARNING: Never look directly into the ends of the fiber or modules.
The light they emit can cause eye damage.
WARNING: Until ready to use, keep fiber patch cables and modules
covered with the included protective caps to ensure connections remain
clean.
Machine Translated by Google

UF-LOCO Quick Start Guide
LAN connection
Power connection
Machine Translated by Google

UF-LOCO Quick Start Guide
Note: The airCube provides Wi-Fi connectivity with a PoE gateway, making it
the ideal complement to the UF-LOCO in CPE installations.
WARNING: The port switch must meet the power specifications
listed in this quick start guide.
O
O
Machine Translated by Google