Ubiquiti UniFi LED ULED-AT User manual

LED
Network-Managed
LED Panel Powered by PoE+
Model: ULED-AT

Introduction
Thank you for purchasing the Ubiquiti Networks® UniFi®LED
Panel. This Quick Start Guide is designed to guide you through
installation and includes warranty terms.
Package Contents
LED
Network-Managed
LED Panel Powered by PoE+
Model: ULED-AT
UniFi LED Panel Quick Start Guide
System Requirements
• An 802.3at-compliant network switch
• UniFi LED mobile app software
• Mobile device: iOS 10 or Android 5.0
• UniFi LED Controller software
• Computer: UniFi Application Server (UAS) 0.5.0,
Ubuntu 16.04 LTS (Xenial Xerus) 64-bit or Debian 9 64-bit
• Web browser: Google Chrome (Other browsers may have
limited functionality.)
• UniFi Dimmer Switch, model UDIM-AT or UDIM-AC

Network Topology Requirements
There are three ways to control the UniFi LED Panel:
UniFi Dimmer Switch Users in the immediate vicinity control
the UniFi LED Panel using the UniFi Dimmer Switch.
UniFi LED App over Layer 2 Network A local user runs the
app to connect to a UniFi AP on the same Layer 2 network as
the UniFi LED Panel.
UniFi LED Controller over Layer 2 Network Alocal user runs
the LED Controller software on the same Layer 2 network as
the UniFi LED Panel.
UniFi PoE Switch
Internet
LAN
WAN
UAP-AC-PRO 802.3at PoE+
ULED-AT
UniFi Application Server
UniFi LED
Controller
UDIM-AT
UniFi LED
App
802.3af PoE
USG-PRO-4
(DHCP Server)
Sample Network Diagram

*640-00332-09*
640-00332-09
Network topology requirements are as follows:
• DHCP-enabled network (for the UniFi LED Panel to obtain
an IP address)
• For UniFi Dimmer Switch only:
A UniFi Dimmer Switch connected to the same Layer 2
network as the UniFi LED Panel
• For LED Controller software:
A UniFi Application Server running the UniFi LED Controller
software and connected to the same Layer 2 network as the
UniFi LED Panel
• For UniFi LED app only:
A UniFi AP connected to the same Layer 2 network as the
UniFi LED Panel

Hardware Overview
Status LED
LED
LED Color Status
Flashing White Initializing.
Steady White System ready.
Steady Blue Adopted by LED Controller.
Alternating
White/Blue Firmware upgrade is taking place.

ULED-AT-XXXXXX
Reset
PoE+
MAC
Sticker
Port
PoE+ The PoE+ port is a 10/100 Ethernet port used to connect
the power and should be connected to the LAN. Power is
provided by a UniFi Switch with 802.3at PoE+.
Note: The PoE+ port requires 25W of power, which can
be supplied by an 802.3at-compliant UniFi Switch.
MAC Sticker Used to scan the MAC address. For details, refer
to “Quick Setup”.
Button
Reset The Reset button serves two functions:
• Restart Press and release the Reset button quickly.
• Restore to Factory Default Settings Press and hold the
Reset button for more than five seconds.

Installation
To install and configure the UniFi LED Panel:
1. Connect one end of an Ethernet cable to the PoE+ port on
the back of the UniFi LED Panel.
2. Connect the other end of the cable to an 802.3at-compliant
switch port that can provide 25W PoE+.
3. Lift the panel and seat it in an opening in the ceiling grid.

Configuring the UniFi LED Panel
Follow the instructions for the software you wish to use:
UniFi LED App
1. Install the UniFi LED app on your smartphone or mobile
device. The app is available from the App Store® or
GooglePlay™Store.
2. Launch the app.
3. Follow the on-screen instructions to configure the UniFi
LED Panel.

UniFi LED Controller Software
1. Install the latest version of the UniFi LED Controller
software on a computer on the same Layer 2 network as
the UniFi LED Panel:
• Ubuntu users Download the software from
www.ubnt.com/download/unifi-led
• UAS users Install the software using the UAS
management console.
2. Launch a web browser and go to https://localhost:20443
3. The UniFi LED Controller will appear, allowing you to
configure the UniFi LED Panel, as well as customize other
settings.
For additional details on the UniFi LED Controller, refer to
the documentation at:
www.ubnt.com/download/unifi-led

Quick Setup
This section describes the Quick Setup procedure for
installations with large numbers of UniFi LED Panels and
Dimmer Switches. The Quick Setup requires using the UniFi
LED app along with a QR Code Log that you create. Each UniFi
LED Panel or Dimmer Switch has a removable MAC Sticker on
its reverse side; this has a QR code used to scan the device’s
MAC address. The Quick Setup consists of these steps:
• Create the QR Code Log
• Install the LED Panels and Dimmer Switches
• Scan the QR codes
Create the QR Code Log
1. Download the QR Code Log template at:
ubnt.link/QR-Code-Log
2. Print out as many copies as needed (each sheet can log up
to 16 LED Panels and 3Dimmer Switches).
Site:
Controller:
QR Code Log
UDIM-AT-XXXXXX
arrows and place them on this QR Code Log.
3. Fill in the Site (such as “1st Floor Meeting Room”) and
Controller (such as “UniFi LED Controller”) on each sheet.