Ubiquiti UF-Instant User manual

UFiber Instant
Package Contents
Installation Requirements
UFiber OLT
Ubiquiti product with SFP port
For more information, refer to: ubnt.link/Using-UF-Instant
Before You Begin
Designing your first GPON deployment requires specific knowledge and planning. For
information on GPON network design and installation, including important considerations
and best practices, refer to:
ubnt.link/UFiber-GPON-Getting-Started
ubnt.link/Designing-a-GPON-Network
For details on configuring U Fiber devices for the first time, refer to: ubnt.link/UFiber-
Initial-Configuration
Hardware Overview
UF-Instant Quick Start Guide

PON Port
SGMII Interface
The SC/APC GPON port supports WAN connections of 2.488 Gbps downstream and
1.244 Gbps upstream.
The SGMII Ethernet LAN interface supports a 1 Gbps connection.
Connecting Fiber
WARNING: Never look directly into the ends of fiber or modules. The emitted light
could cause damage to the eye.
WARNING: Until ready for use, keep modules and fiber patch cables covered using
the included protective caps to ensure the connections stay clean.
WARNING: DO NOT connect the device directly to a UFiber GPON module (UF-GP-
B+ or UF-GP-C+). Doing so will damage the device optics. Ensure that the device’s
received signal level never exceeds -8 dBm. Use a UFiber PLC Splitter to add
attenuation as needed.
UF-Instant Quick Start Guide

1.
2.
Connecting LAN
UF-Instant Quick Start Guide

Configuration
The device only supports bridge mode and is configured via the UFiber OLT. For more
information, refer to the UFiber resources, which are available at: ubnt.link/UFiber-
Support
Specifications
UF-Instant
Dimensions 69.46 x 13.70 x 11.30 mm
(2.74 x 0.54 x 0.45")
Weight 30 g (0.96 oz)
Networking Interfaces (1) SC/APC, GPON WAN
(1) SGMII Ethernet LAN
Networking Interface Speeds
GPON WAN, ITU G.984 2.488 Gbps Downstream,
1.244 Gbps Upstream
GbE LAN 1 Gbps
Management Interface In-Band Ethernet
PON
Normal Optical Power Range TX (Class B+): 0.5 to 5 dBm
RX: -8 to -28 dBm
Power Method SFP
UF-Instant Quick Start Guide

UF-Instant
Power Supply 3.3V
Max. Power Consumption 2W
Supported Voltage Range 3.3V
Processor Specs MIPS 100 MHz
Memory Information 32 MB DDR
Operating Temperature -10 to 45° C (14 to 113° F)
Operating Humidity 10 to 90% Noncondensing
Certifications CE, FCC, IC
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.
WARNING: CLASS 1 LASER PRODUCT, IEC/EN 60825 ‑ 1:2014 - Do not look into the ends of the
fiber optic cable or SFP modules while converters are powered.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements indicated on
the manufacturer’s label. Connection to a different power source than those specified may result in
improper operation, damage to the equipment or pose a fire hazard if the limitations are not
followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a
qualified service technician.
Limited Warranty
ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and,
where applicable, specify arbitration instead of jury trials or class actions.
UF-Instant Quick Start Guide

Compliance
FCC
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
ISED Canada
CAN ICES-3(B)/NMB-3(B)
Australia and New Zealand
CE Marking
CE marking on this product represents the product is in compliance with all directives that are
applicable to it.
WEEE Compliance Statement
UF-Instant Quick Start Guide

Declaration of Conformity
Online Resources
© 2021 Ubiquiti Inc. All rights reserved.
UF-Instant Quick Start Guide