UDAP Bear Shock CF4 User manual

#CF4 - 4ft. Lightweight Electric Camp Fence
Bear Shock Contents
Thank you for purchasing Bear Shock electric fence! Please read the
following instructions carefully to become acquainted with some of the
important features of your new lightweight electric fence. This high-
performance device must be installed and operated properly in order to
achieve the best possible results.
Bear Shock is designed to provide safety and sound sleep while in bear
country and to help protect you and your equipment from curious bears
by providing a surprising electrical shock when touched.
UD P Industries, Inc. has proudly produced one of the finest, highest-
quality battery-operated lightweight electric fence systems available.
Two D-cell batteries (not included) power the Bear Shock fence
energizer. Because of the efficient electronic circuit design, two alkaline
D-cells will last approximately 5 weeks under continuous operation,
depending on fence and weather conditions.
Bear Shock is fully adjustable and can easily adapt to most
environments. There is enough poly wire to fence an area 27 ft by 27 ft.
much smaller/larger area can be fenced by cutting/tying the poly
wire. If cut, the poly wire can later be tied back together if a larger area
is preferred.
This electric fencing system presents a mental barrier to an animal
rather than a physical barrier. Once an animal is shocked, even though it
has not been harmed, it will respect the fence out of fear of being
shocked again.
Caution
Bear Shock does not
replace recommended
safety measures. Never
store food or odorous
items in or near your
sleeping area. For
recommended
procedures for camping
in bear country, refer to
the Bear Safety Tips
Booklet provided. For
additional safety in bear
country have UDAP
Pepper Power Bear Spray.
Assembly Directions
1 Pole and wire assembly
1. Each corner pole will need to be assembled. Included
with this product are 24 pole insulator clips. Install
three clips on each corner pole by twisting the clip
clockwise onto the pole. Be sure that the open end of
the clip is facing up. The portion of the corner pole
with the metal insert is the bottom piece. Install one
clip in the middle of the bottom section of the corner
pole. Install one clip just above the metal insert of the
top pole and then install the third clip a couple inches
from the top of the corner pole. (See Picture)
2. fter corner poles are assembled place at the 4 - 8
corners of your site. Depending on how many posts
needed.
3. Push each corner pole into the ground at a 30-
degree outward angle deep enough to keep them
stable. Rocks or other material may be used as
braces stacked around poles if poles fail to stay in
ground.
NO E: he poly wire requires some pre-assembly. his is a
one-time assembly process and does not need to be done
again. Please read “Poly Wire Initial Assembly Directions”
before continuing for the first time.
2 Poly Wire Initial Assembly
1. The spool of poly wire comes in three equal lengths of 110
feet each.
2. t one end of
each wire tie a
small loop (See Picture). Once the
loop is tied you may run the poly
wire around your fence.
3. t the other end of the poly
wire complete the below
assembly.
4. Included in the Bear Shock kit
is three metal Snap Hooks and
three plastic Line Tighteners.
The Line Tightener is the small plastic piece with three holes
(See Picture).
UDAP Industries Inc.
P.O. Box 4872
Butte M , 59702
Phone: [phone]
Fax: [phone]
Email:
[e-mail]
PepperPower.com
Part Qty
. UD P Bear Safety Tips Booklet 1 ea.
B. Hot wire 1 ea.
C. Ground wire 1 ea.
D. Flagging tape 1 roll
E. Energizer 1 ea.
F. Poly wire line tightner and snap hook 3 ea.
G. 3 Electrical poly wires (180’ ea.) spooled 1 ea.
H. 4 foot Plastic-coated support poles (top and bottom)
with a total of 3 black insulators clips attached to each
assembled pole
8 ea.
I. Ground stake 1 ea.
J. Storage bag 1 ea.

5. To attach the Line Tightner weave the poly wire though the
holes of the Line Tightener at either end, and tie the poly wire
to the other end (See Picture on Previous Page).
6. ttach the
metal snap
hook in the
loop next to
your knot (See
Picture).
7. Complete this assembly for all three poly-wires.
8. Insert the first poly wire’s loop
into the lowest black insulator in
the location where you want your
opening and unwind poly wire off
winder. (Figure 1).
9. Slide the poly wire into each black
insulator on the poles as you
position the wire around the
inside of the poles.
NO E: The opposite end of the poly
wire contains a metal clip, which will
be used to hook into the beginning
loop of the poly wire once you wrap
it around the perimeter.
10. Hook the clip end of the poly
wire to the poly wire’s loop (Figure 2). The hook completes
the connection.
NO E: Do not over tighten the poly wire at this time.
11. Repeat steps 4 through 6 until all three poly wires are attached
to the poles.
12. Using the Line Tightener
located behind the poly wire
metal hook, adjust the tightness
of each poly wire until they
have equal tension (Figure 3).
Tighten only until the slack is
removed.
NO E: void over tightening,
which will cause other wires to sag.
13. s you tighten, slide the Line
Tightener back to take up the
slack.
14. Use the flagging tape to mark
the two top poly wires for
visibility (Figure 4).
IMPPOR AN : A common behavior of bears is to investigate
the flagging tape once near the fence. Increasing the likelihood
of getting a good shock.
NO E: Make sure there are no green branches or other vegetation
touching the top two poly wires as they will weaken the voltage
and deplete the batteries. The bottom poly wire may be touching
the ground, as it is a grounded wire.
3 Energizer hookup Important Safety Information
Read Energizer Instructions Carefully.
WARNING: ny alteration to the design of this energizer may
cause serious electrical shock and may void the warranty.
• Install the energizer and the electric fence according to these
installation and operating instructions.
• Inform everyone, especially children, who might possibly
come into contact with the electrically charged fence, about
its location and operation. Do not allow young or infirm
persons to use this electric fence energizer without
supervision. Do not allow young children to play with this
energizer or near an electric fence or electrified wires.
• Instruct all persons how to disconnect the energizer in case of
emergency
• Never climb over an electric fence wire while it is electrically
energized
• Never install an electric fence below high-voltage poser plant
transmission lines.
• Never use more than one electric fence energizer on the same
fence.
• properly installed ground stake electrically connected to the
fence energizer output ground terminal provides grounding of
this product. The energizer must be grounded. If the energizer
should malfunction, grounding will reduce the risk of
electrical shock by providing a path of low resistance for the
electric current.
DANGER: n internal fault on an improperly grounded fence
energizer could result in a risk of harmful electric shock on the
electrified fence.
3.1 Insert batteries (See Energizer Instructions)
3.2 Install your energizer to the electric fence
1. ttach the energizer directly to the
fence poly wire using the unique
top stay-on clip. ttach the stay-on
clip to the middle poly wire by
inserting the stay-on clip into the
poly wire starter loop (Figure 5).
This will allow you to hang the unit
without sagging the fence.
2. Choosing a color, attach the “hot”
wire with alligator clips between the
top two poly wires using the
alligator clips.
3. ttach the green ground clamp that is attached to the
Energizer to the ground stake.
4. ttach the other color “ground” wire to the bottom poly wire
and to the ground stake using the alligator clips. Put the small
alligator clip into the hole of the ground stake to clamp it.
5. Your energizer is ready to be turned on (See Energizer
Instructions).
Questions: Call Toll Free 866 EAR 911
8:00 AM - 5:00 PM MST Monday through Friday
ATTENTION! DO NOT RETURN TO STORE!
For product repair or return please call UDAP Industries at 406-494-9292
Disclaimer
DO NOT SEEK OUT ENCOUNTERS WITH BEARS. THIS PRODUCT IS A BEAR DETERRENT WHICH MAY PROTECT USERS IN SOME
UNEXPECTED CONFRONTATIONS WITH BEARS BUT MAY NOT BE EFFECTIVE IN ALL SITUATIONS OR PREVENT ALL INJURIES OR
DAMAGES. READ CAREFULLY THE ENTIRE INSTRUCTIONS UPON PURCHASE & BEFORE TAKING THIS PRODUCT INTO AREAS
WHERE BEARS MIGHT BE ENCOUNTERED. KEEP OUT OF REACH OF CHILDREN.
TO THE EXTENT ALLOWED BY LAW, UDAP INDUSTRIES, INC. SHALL NOT BE LIABLE FOR DAMAGE, INJURY, LOSS, DIRECT OR
CONSEQUENTIAL INCLUDING DEATH ARISING OUT OF THE USE OF, OR INABILITY TO USE THIS PRODUCT.
PepperPower.com