UGREEN Car Cup Holder Phone Mount User manual

1
IMPORTANT
Please read this manual before using the unit to ensure safe and proper use.
The unit will generate the magnetic/electric field; never place any medical
equipment; watches; credit card; magnetic record card or any magnetic
sensitive products close to the unit.
Only phones with built-in QI wireless system can recharged by this unit. For
details, please refer the user’s manual of your phone.
The design of the unit is indoor use. Never spill or spray any type of liquid on the
product.
Do not use this product near water and moisture, for example: near a bathtub,
washbowl, kitchen sink or laundry tub; in a wet basement; or near a swimming
pool.
Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
Clean only with dry cloth. Unplug this product from external USB Charging
Devices before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry
cloth for cleaning.
Do NOT place any heavy object on the Charging Surface. It may damage the unit.
When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or those that have the same
characteristics as the original parts. Unauthorized substitutions may result in fire
or electric shock or other hazards.
August 27, 2021_V1

2
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. Modifications not
authorized by the manufacturer may void user’s authority to operate this device.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
August 27, 2021_V1

3
INSTALLATION
Before use, assembled the Car Mount to the Charger as follows:
1. Loosen the Knob on the Charger by turning it counterclockwise as illustrated
below:
2. Insert the Car Cup Holder Phone Mount into the Charger as illustrated below:
3. Tighten it by turning the Knob clockwise as illustrated below:
August 27, 2021_V1

4
4. Loosen the Knob on the Mount by turning it counterclockwise as illustrated
below:
5. Pull out the pivot arm to the needed height then tighten it by turning the knob
clockwise as illustrated below:
MOUNTING
Mount the charger into your vehicle as follows:
1. Rotate the striped Circle counterclockwise to outspread the three Squares.
August 27, 2021_V1

5
2. Outspread the three Squares to suitable position based on the diameter of Car
Cup Holder, Put the charger into the Car Cup Holder.
CONNECTION
Connect the Charger to your Car USB Charger (not included) as follows:
1. Connect the Type-C USB Plug from the supplied USB connection cable to the
Type-C USB Port on the Charger as illustrated below:
2. Connect the full size USB Plug to the USB Port on your Car USB Charger (not
included) as illustrated below:
3. The Red Power On Indicator on the Charger will illuminate.
August 27, 2021_V1

6
WIRELESS CHARGING
1. Mount the unit into your vehicle then connect it to your Car USB Charger as
previously instructed.
2. Press the Release Button on the rear of Charger to release the Clip as illustrated
below:
3. Place your cell phone onto the Charging surface as illustrated below:
4. Adjust the location of cell phone by sliding the Holder up/down as illustrated
below until the color of the Red Indicator on the Charger turns to blue (or, the
charging icon appears on the cell phone’s display) to start charging.
(Note: If the location of the cell phone is incorrect, charging will NOT proceed.)
August 27, 2021_V1

7
5. Closed the Clip to hold the cell phone as illustrated below:
Notes:
1. To charge a cell phone with the Charger, the cell phone must be compatible with
the Qi standard for wireless charging.
2. During charging, if the cell phone has a cover or case, it may disturb or prevent
the wireless charging function of the cell phone.
3. The charging transmission distance of the unit is less than 5mm, the thickness of
cell phone cover of case can NOT over 8mm.
4. To maximize the charging speed, using a Car USB Charger (not included) equipped
with Quick Charger 3.0 USB port.
5. To save energy, disconnect the Charger from the Car USB Charger if not using it for
an extended period of time.
GENERAL SPECIFICATION
Wireless Charging Type: Qi version 1.2.4
Input:
DC
5V/2A, 9V/1.67A
Output: 5V/1A, 9V/1.2A
Transmission Distance: Up to 5mm
PACKAGE INCLUDES
1. Charger
2. Car Cup Holder Phone Mount
3. USB Connection Cable
4. User Manual
5. Quick Start Guide
August 27, 2021_V1

8
DISCLAIMER
This device only supports smartphones with wireless charging capability. If your
smartphone does not have wireless charging capability, you may need to purchase
a compatible wireless receiver.
SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE
Need help?
We’re here for you every day from 7 a.m. - 9 p.m. CST.
Give us a call at 1-888-516-2630
August 27, 2021_V1

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be
installed and operated with minimum distance between 20cm the radiator your body: Use
only the supplied antenna.