Ugur UBM 20 User manual

PORTABLE AUTOMATIC ICE MAKER
UBM 20
INSTRUCTION MANUAL
It is important that you read these instructions before using your portable ice maker and we strongly recommend
that you keep them in a safe place for future reference.

1
I
IM MP PO OR RT TA AN NT T S SA AF FE ET TY Y I IN NS ST TR RU UC CT TI IO ON NS S
…………………………………………………….2
P
PR RE EP PA AR RI IN NG G Y YO OU UR R I IC CE E M MA AK KE ER R F FO OR R U US SE E
IMPORTANT SAFETY TIPS …………………………………………………………………..3
G
GE ET TT TI IN NG G T TO O K KN NO OW W Y YO OU UR R U UN NI IT T … …… …… …… …… …… …… …… …… …… …… …… …… …… …… …… …… …… …… …… …… …… …… …4 4
OPERATING PROCEDURES & MAINTENANCE
UNPACKING YOUR ICE MAKER …………………………………………………………….5
CONNECTING YOUR ICE MAKER …………………………………………………………..5
CLEANING AND MAINTAINING YOUR ICE MAKER ………………………………………5
U
US SI IN NG G Y YO OU UR R I IC CE E M MA AK KE ER R
…………………………………………………………………….6
T
TR RO OU UB BL LE ES SH HO OO OT TI IN NG G
………………………………………………………………………….7
T
TE EC CH HN NI IC CA AL L P PA AR RA AM ME ET TE ER RS S & & C CI IR RC CU UI IT T D DI IA AG GR RA AM M
……………………………….. 8
TABLE OF CONTENTS

2
DANGER
WARNING
IMPORTANT SAFETY INSTRUCTIONS…
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual in regards to your appliance.
Always read and obey all safety massages.
This is the safety alert symbol:
!
All safety messages will follow the safety alert symbol and the word “DANGER” or “WARNING”.
You could be seriously injured if you do not follow the immediate instructions.
All safety messages will describe the potential hazard, inform you on how to reduce the chance of injury, and indicate
what can happen if instructions are not followed.
DO NOT TOUCH THE EVAPORATOR WHILE THE UNIT IS IN USE OR DURING THE ICE MAKING PROCESS. IT
MAY CAUSE SEVERE BURNING.
Evaporator Rods

3
When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock,
and injury to persons or property. Read all instructions before using any appliance.
This machine is not a freezer, therefore cannot store the made ice. To store ice and keep frozen, please transfer
to a regular freezer.
Do not operate this or any other appliance with a damaged cord.
Connect to properly polarized outlets only. No other appliance should be plugged into the same outlet. Be sure that
the plug is fully inserted into the receptacle.
Do not run cord over carpeting or other heat insulators. Do not cover the cord. Keep cord away from traffic areas,
and do not submerge in water.
We do not recommend the use of an extension cord, as it may overheat and become a risk of fire. If you must use
an extension cord, use No.2.0mm2minimum size and rated no less than 1875 watts.
Unplug the ice maker before cleaning or making repairs.
Exercise caution and use reasonable supervision when appliance is used near children.
Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or explosion.
Do not tip over.
If the ice maker is brought indoors from outdoors during the wintertime, give it a few hours to warm up to room
temperature before plugging it in.
PREPARING YOUR ICE MAKER FOR USE

4
8
4
1. Ice Case Panel: The panel that pushes already formed ice into the ice basket below.
2. Ice Basket
3. Control Panel: Easy to use, visible functions and 1-touch display setting.
A) Selects ice cube size.
B) Starts or stops ice making cycle.
4. Handle
5. Water Drain Cap: For draining water from the water reservoir.
6. Cover: With a transparent window to allow interior visibility.
7. Ice Shovel/Scoop.
8. Ice Sensor: Ice sensor determines when the ice basket is full.
MAXIMUM WATER LEVEL: ▼
This marking can be found on the inside of the water tank.
GETTING TO KNOW YOUR UNIT
A
6
5
7
1
B
3
2

5
DANGER
UNPACKING YOUR ICE MAKER
1. Remove all exterior and interior packaging. Check that ice basket and ice scoop is included. If any part or
accessory is missing, please contact our customer service.
2. Clean the interior with lukewarm water and a soft cloth. Remove the ice basket and wash it in warm water.
3. Wipe clean the evaporator rods using a water/vinegar solution.
4. Find a location for your ice maker that is protected from direct sunlight and other sources of heat (i.e.: stove,
furnace, radiator). Place the ice maker on a level surface. Maker sure that there is at least 15cm of space between
the back and sides of your ice maker and the wall.
5. Allow the refrigerant fluid to settle for several hours before plugging in the unit.
6. The appliance must be positioned so that the plug is accessible.
CONNECTING YOUR ICE MAKER
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged
please call our customer service.
1. This unit should be properly grounded for your safety. The power cord of this appliance is equipped with a
three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electric shock.
2. Plug your appliance into an exclusive, properly installed, grounded wall outlet. Do not under any circumstances, cut
or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should
be directed toward a certified electrician.
3. This appliance requires a standard 220-240 volt, 50Hz electrical outlet with three-prong ground.
Before using your ice maker, it is strongly recommended to clean it thoroughly.
CLEANING AND MAINTAINING YOUR ICE MAKER
Remove the ice basket.
1. Turn the drain cap counter clockwise to drain out the water.
2. Clean the interior with diluted detergent, warm water and a soft cloth.
3. The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water.
4. Dry the interior and exterior with a soft cloth.
5. Close the drain cap.
6. When the machine is not in use, open drain cap to drain water completely from water reservoir.
OPERATING PROCEDURES & MAINTENANCE
The ice maker is not designed to be installed in an outside area such as a garage or a
porch. Ambient temperatures of below 10℃or above 38℃will hinder the
performance of the appliance.

6
The ice maker should be cleaned on a regular basis. (See: “HOW TO CLEAN”)
It is necessary to have an adequate ventilation space around the ice maker in order to sustain proper performance,
dissipation of heat, maintain efficiency, and low power consumption. Clearance of minimum 15cm should be
maintained at the rear and sides of the unit and 20cm at the top of the unit.
To attain proper performance, be sure to plug the appliance into a properly grounded 220V/50Hz outlet.
Do not modify the power cord under any circumstances to allow the unit to be plugged into a non-grounded outlet.
To avoid heat damage to the power cord, please ensure that it does not come in proximity or in direct contact with
the compressor of the ice maker.
Please avoid installing the ice maker in a location where the appliance will come in contact with water or moisture
to minimize rusting of metal parts.
The ice maker should not be installed near any heat source or in a location where it will come in direct contact with
the sunlight.
1. Clean your ice maker first.
2. Open the cover, remove the ice basket and pour water into tank.
Keep water level below the level mark: ▼
3. Place the ice basket back into the ice maker and close the lid.
4. Plug in the unit and the power indicator light will blink.
5. Press “Power” on the control panel to begin the ice making cycle. The power indicator light will lit.
6. Select the size of the ice cube by pressing the “Select” button. If ambient temperature is below 15℃, it is
recommended to select small or medium size to avoid ice sticking together.
7. The ice making cycle lasts 6 to 15 minutes, depending on the size of the ice cube selection & room temperature.
*NOTE: When the machine is brand new, it may sometimes take a few hours for the machine to adjust and get used
to producing ice at a faster rate, and producing larger cubes of ice. This is considered normal.
8. While the icemaker is on, check water level periodically. If water pump can’t inject water, the ice maker will stop
automatically, and the “Water” indicator will be on.
Press “Power” button, fill water up to the level mark and press “Power” again.
Allow 3 minutes for the refrigerant to settle before restarting.
9. The ice maker automatically stops working when the ice basket is full.
10. Change water in the water reservoir every 24 hours to ensure a reasonable hygiene level.
If unit is not in use for a few days stretch, drain all water in the tank reservoir and reflll before operating again.
USING YOUR ICE MAKER
CARE AND MAINTENANCE

7
USING YOUR ICE MAKER
PROBLEM
POSSIBLE CAUSE
SOLUTION
“Water” indicator is on.
Water level is too low.
Stop the ice maker, fill water, and restart.
“Ice” indicator is on.
Ice basket is full.
Remove ice from ice basket.
“Water” and “Ice” indicator
are both flashing.
Ice shovel is stuck.
Check if ice is blocking the ice shovel,
otherwise, consult a certified technician.
Ice cubes stick together.
Ice making cycle is too long.
Stop the ice maker, and restart when the
ice blocks melt. Select the small ice
size.
Water temperature in inner tank is
too low.
Change the water in the reservoir. Use
water between 5℃-32℃.
Ice making cycle is normal
but no ice is made.
Ambient temperature or water
temperature in inner tank is too
high.
Please operate the ice maker below
ambient temperature of 32℃and use
cold water.
Refrigerant liquid leakage.
Consult a qualified technician.
Pipe in the cooling system is
blocked.
Consult a qualified technician.
Ice Maker is leaking water
The water drainage cap may be
not be tightened properly.
Tighten the drainage cap.
The ice cubes are melting.
Location of appliance may cause
temperature changes.
Also constant opening and
shutting of the lid may also cause
variable temperature fluctuations.
Leaving ice in the appliance for an
extended period of time may also
result in the appliance recycling
the ice by melting it down and
making a new batch.
Make sure the appliance is always
placed in a temperature regulated area.
Avoid leaving the lid open.
Transfer ready-made ice to another
container and store in a cooler or freezer
to avoid recycling.
TROUBLESHOOTING

8
Troubleshooting Continued…..
There is enough water in the
water tank, but the indicator to
“add water” stays on and the
unit will not function.
The water filter on the bottom of
the water tank may be blocked.
Remove the water filter and clean it.
________________________________
After following the procedure outlined in
#8 under the “Using your Icemaker”
section, if your icemaker still does not
start producing ice please try the
following two procedures:
1) Follow the steps outlined in #8,
then wait approximately 5-10
minutes and press the ‘Power’
button again.
2) Unplug the unit’s power supply,
wait approximately 5-10 minutes,
plug the power supply back in,
follow the steps outlined in #8.
Ice cube sizes are inconsistent
The ice case panel may not be
level.
Adjust the ice case panel and make sure
it is level.
There is not enough ice cubes
in the ice basket, but the
indicator of “ice full” is on.
The room temperature may be too
low, around 5℃
___________________________
The ice cubes being formed may
be touching the sensor
occasionally when the ice case
panel pushes the ice cubes into
the ice basket.
Make sure the unit is in an area where
the temperature is above 5℃regulated.
_______________________________
Remove the ice cubes, wait for a few
minutes to let the unit restart again.

9