UIS STH-230 User manual

Wireless Temperature & Humidity SensorWireless Temperature & Humidity Sensor
Overview
Name: Wireless Temperature & Humidity Sensor
Battery Type: CR123A x 1
Dimension: 21 x 69 x 23.5 mm
Accessories: Double-side Tape
Names of Parts
1. Status LED
2. SET Button
3. Battery Slot
Features
Power Saving – one CR123A battery can be used for more than 2 years. It is also equipped with the low battery alert function.
Every 5 seconds, it will read temperature & humidity.
Easy Setup – Simply press the SET button at the front of the device to join the system at the rst time.
Open the top cover. Insert battery and close the cover.
Wireless Temperature & Humidity Sensor
Installation Guide
Installation Guide
Installation Guide
STH-230
CAUTION
RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
69mm
23.5mm
21mm
1
2
3
III. Device Deletion (Back to factory default settings)
1. First, Login into website.
About Login methods, please refer to 4.Basic Setting of Installation in Wireless Gateway Installation Guide. (Page1).
2. To remove the device joining, take out the
battery, long press SET button 10 seconds.
3. Delete the device from the website.
(See the features on the right side.)
4. Press and hold the set button of the
device to install the battery. (Do not
release the button while installing
the battery.) After 6 seconds, the LED
indicator blinks light blue once and
starts blinking. That means device
deletion sucessfully. (Please complete
the procedure in 3 minutes.)
1
2
3
Installation
I. Before Installation
1. Power on the Gateway.
2. Waiting for about 90 seconds until the Gateway led light become solid
green instead of blinking.
Note: We suggest to use auto joining all device via APP at the rst time.
Please refer to APP Quick Installation Guide.
II. Device Installation and Manual Joining
1. Press the both side of STH-230 to open top cover. Install the battery .
Note: Do not use rechargeable battery.
2. Press the SET button at the top of the Gateway or short press the set button
at the bottom of Router (Power Switching). Then press the SET button of device.
3. The Gateway/Router and the device are joining as both LED indicators blink blue light around 60 seconds. The device blinks
light blue LED indicators once and turns o, indicating the device joining process is successful.
Note: If the device joining process is failed, both LED indicators on those joined devices will light blue and stop blinking after
60 seconds.
4. Use the double-sided tap or athead screw to x bottom case.
Note: After device deletion,it will back to auto joining mode.

Notice
Please install the device in a well-ventilated location.
Do not expose to direct sunlight, heat or high humidity.
Avoid wet from rain.
Install the batteries with the correct polarity (+/-) as shown inside the battery compartment.
Troubleshooting
Problem Solution
The LED indicator lights abnormally
when linking to the system.
Cannot link to the system.
a. Make sure the battery has been properly installed and its power is adequate.
b. Reset to factory default (Please see Installation,III. Device Deletion), and
re-join to the system.
c. If the problem persists, please contact your local distributor.
Check the distance between device and Gateway/Router (line of sight) is 80
meters (max). If there is any obstructions (i.e. walls or metal objects) between the
devices, the distance will be shorter. Users can move the device closer or add a
Router, then try again.
Specifications
Wireless Temperature & Humidity Sensor
Communication Protocol
Frequency
Operation Range
Power Consumption
CPU
LED Indicator
Temperature Accuracy
Humidity Accuracy
Battery Type
Battery Life
Low battery life
Environmental
Specication
Dimension (W x H x D)
Weight
Zigbee Pro ZHA1.2
2.4 GHz ISM band
Up to 80 meters (LOS)
Working: max 38mA
Standby: max 3uA
JN5169
Blue 1PCS LED
Status: Trigger LED Flash
Join LED Flash
±0.5℃
±5RH
CR123A Battery (3V) x 1
Up to 2 years
3 Weeks
Operating Temperature 0°C ~ 40°C
Storage Temperature -20°C ~ 70°C
Humidity 90% RH Max, Non-Condensing
21 x 69 x 23.5mm
(w/o Battery) 14g
RF exposure warning statement

Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible
for compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that may cause
undesired operation of the device.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
cm between the radiator and your body.