RELAX-A-MIST CR-9 User manual

CN2
2016
Q
UALITYSTEAMBATH EQUIPMEN
T
R E L A X MIST
A
®
1www.relax-a-mist.com1-800-Y-U-STEAM (1-800-987-8326)
LR 42682-8
1. GENERAL INFORMATION
The Relax-A-Mist®  me and temperature control is a simple
programmable control. The user friendly design has programmable
 me and temperature se ngs. Once a program is set and running,
you may temporarily override the se ngs by pressing the  me
or temperature bu ons and the applicable increment arrow.
Upon comple on of the  med se ng, or hal ng your steam
bath with the “on/o ” bu on, your temporary override se ng
will return to the programmed default se ngs. Your steam bath
is ready for your next use. Power supply interrup ons will not
change or delete your default  me and temperature se ngs.
The digital  me and temperature control switch comes as a
package complete with the following:
1. One programmable Time and Temperature Control.
2. One Remote Control.
3. One 25 foot cord set (steam generator connec on wire
to control) with a modular male plug-in at the steam
unit and a modular female plug-in at the control, inside
the steam room.
The programmable Time and Temperature Control switch
must be located inside the steam room, approximately 4
feet o the  nished  oor, and NOT in an area above the
steam nozzles. The thermostat sensor is built into the bo om
of the Time and Temperature control. The remote control
can only operate the main control from a direct line of site.
Before commencing with these instruc ons, ensure
the Relax-A-Mist® steam generator has been installed
according to the steam generator installa on instruc ons.
NOTE: Inside of the steam room, the six inch wire on the back
of the Time & Temperature control (with the male plug),
connects into the 25 foot wire (with the female plug). At
the steam generator, the male plug from the 25 foot wire
connects to the female plug located on the side of the
steam generator’s electrical box marked “Timer Switch
and 24 VAC”. The cord set modular female connec on
must be iden  ed at the steam generator (do not plug
the switch cord into the automa c drain connec on).
The control’s 25 foot cord set wire must be installed
during the rough in, with the male end at the steam
generator and the female end at the area in the steam
bath where the control will be installed on the wall.
2. ROUGH IN
ELECTRICAL (According to local electrical code)
Before commencing, check to ensure that the
Relax-A-Mist® steam generator has been installed
according to the steam generator installa on instruc ons.
Install only the Relax-A-Mist® 25 foot cord set wire (compa ble
with the Quick Touch Timer or the Time and Temperature
Control) ensuring that the modular male plug is located in the
area where the steam generator is to be installed. The modular
female connector of the 25 foot wire should protrude out of the
wall about 6 inches into the shower or steam room where the
control will be installed. You will need to make the hole in the
cement board and the  nished  le approx. 7/8” diameter to
allow the modular wire connectors from the control and the 25
foot cord set to pass back inside the wall for the  nal installa on.
DO NOT ADHERE CONTROL TO WALL UNTIL YOU HAVE
COMPLETED THE STEAM GENERATOR START UP AND CONTROL
PRETEST.
CAUTION CAUTION CAUTION
DO NOT STRETCH THE WIRE TIGHT. DO NOT STAPLE THE WIRE
TO STUDS. CHECK ORIENTATION OF MODULAR CONNECTORS
ON CONTROL CORD SET TO ENSURE MALE END IS AT STEAM
GENERATOR AND FEMALE END IS IN THE AREA THE CONTROL
WILL BE LOCATED, INSIDE THE STEAM SHOWER.
NOTE: The electrical “supply” for the steam generator CANNOT
be switched directly by the Time and Temperature
Control.
The power supply cable must be run directly to the steam
generator from the fuse or circuit breaker panel. A separate
USE ONLY RELAX-A-MIST®FACTORY SUPPLIED PARTS
FOR MODELS JR-1, JR-2, JR-3, JR-4, CR-9, CR-11, CR-12, & CR-14
INSTALLATION INSTRUCTIONS
TIME & TEMPERATURE CONTROL
with HANDHELD REMOTE
CONTROL
CORD SET
TIME &
TEMPERATURE
CONTROL
REMOTE
CONTROL

2www.relax-a-mist.com1-800-Y-U-STEAM (1-800-987-8326)
INSTALLATION INSTRUCTIONS - TIME & TEMPERATURE CONTROL
2www.relax-a-mist.com1-800-Y-U-STEAM (1-800-987-8326)
Relax-A-Mist® switch cable must be run from the steam
generator to the control. The mer control through the
switch cable acvates a contactor in the steam generator.
3. FINAL INSTALLATION
ELECTRICAL (According to local electrical code)
Check to ensure that the Relax-A-Mist® steam generator has
been installed according to the steam generator installaon
instrucons.
Cauon: Idenfy modular connector lock posion before
inserng into female connecons on steam unit or
switch.
a) At the steam generator electric box, side panel, remove
the protecve label from the modular female plug marked
“Remove to Insert Modular Connector”. Note: There
may be a second plug for Oponal Automac Drain.
b) Insert the male plug of the 25 foot mer cord set, with
the retaining tab to boom, into the steam generator
electrical box female plug. The female socket is marked
“TIMER SWITCH” and “24 VAC”. The other female
plug is for the oponal automac drain feature. This
female plug may be sealed with a blank plasc cover
if the auto drain opon was not factory ordered.
c) Insert the other end of the 25 foot steam generator
connecon cord set onto the male plug of the
programmable me and temperature control.
DO NOT CUT FACTORY WIRING TO INSTALL THE TIME
AND TEMPERATURE CONTROL.
DO NOT FORCE MODULAR CONNECTIONS.
DO NOT ADHERE TIME AND TEMPERATURE CONTROL
TO THE WALL UNTIL THE CONTROL PRETEST HAS
SUCCESSFULLY BEEN COMPLETED.
d) Once the control pretest is completed, tuck the excess
cord behind the switch into the wall or electrical box if
provided. Peel and sck the control to the wall. If a gap
appears between the wall and the switch, the perimeter
of the switch may be sealed with silicone, or if single gang
electrical box is provided, adjust the electrical box so as
not to protrude through the nished surface of the wall.
STEAM GENERATOR START UP and CONTROL PRETEST
To start, make sure that the electrical and water supplies are turned o and that the programmable switch is not illuminated.
Turn on the water supply to the steam generator. No water will enter as the electricity is sll o at this point.
Turn on the electrical supply to the steam generator at the electrical panel or power supply switch to start the pretest.
When the correct voltage is supplied to the steam generator the control will illuminate the digits to display 3 bars. Press
the ”on/o” buon. This will illuminate the display in the control to show numbers (changes from bars) and will energize
the steam generator contactor coil which will be noceable by an audible “click”. When the steam unit’s contactors
close, the water level device and water valve will be energized. The water entering the boiler will be audible in the form
of several short “spurts”. The water will stop entering the boiler when the opmum water level has been achieved. The
contactor and water valve are indicated by a red LED light and a green LED light illuminang on the circuit board in the steam
generator electrical box. Once the steam unit water level is sased, the green LED light will turn o and the red LED light
will remain illuminated, indicang the steam unit is in the heang mode. Turn o the control as the pretest is now complete.
Peel and sck the control to the wall in the shower or steam room. Press the “on/o” buon and start the steam unit.
Approximately 2 minutes aer starng the control the steam generator will produce steam and it will be entering the
shower or steam room. The rst me the generator is turned on (during the start up), there may be an inial burst of
hot water from the steam nozzle unl the steam line has come up to temperature. The water from this start up test
should be captured as it may contain impuries from the soldering process during the rough-in connecon of the steam
lines. When the steam room has heated to the control’s programmed set point, sit back and enjoy, Relax-A-Mist®.
DISCLAIMER
The above informaon represents suggesons only; each steam room is unique. Relax-A-Mist® manufactures steam generators
only and therefore cannot warrant informaon given regarding steam room materials or construcon technicques. Final
selecon of the steam room temperature seng and duraon of stay is at the descreon of the operators and owners.

3www.relax-a-mist.com1-800-Y-U-STEAM (1-800-987-8326)
INSTALLATION INSTRUCTIONS - TIME & TEMPERATURE CONTROL
HOW THE SWITCH WORKS:
The “on/o” buon starts and stops the control programs. Aer a program has been set and saved, simply press the “on/
o” buon and temperature and me will be displayed on the readout (only one program can be set and run at a me).
When the “on/o” buon is pushed the control readout will rst display the temperature of the steam room, followed by the temperature
set point ashing and then the programmed steam bath me in minutes. If the room temperature is lower than the controls set point
temperature, the steam generator heang cycle will start. The heang cycle will raise the temperature in the steam room to the preset
programmed temperature during the count down of the programmed me. When the room temperature matches the preset temperature
(average steam room 1150F, or at your temperature seng) the control will start and stop the heat and steam entering the room within
approximately one degree of the temperature set point. Once the control has begun the me count down cycle, you may switch the display
from me to temperature and adjust the sengs by pressing either the “me” or “temperature” buon and the up and down arrows.
While enjoying a steam bath you may override the programmed sengs by selecng the me or temperature buon.
Push the me buon to display the me and arrow up or down for this steam room visit (use) only. Push the temp
buon and arrow up or down to change the temperature display reading from “C” to “F”. A second push of the “temp”
buon while in the temp mode, will display the set point reading for 15 seconds and can be arrowed up or down to
adjust the temperature for this steam room visit (use) only. Pressing the up or down buons unl the desired increment
is reached will not aect your programmed sengs (program sengs can only be changed when they are ashing).
When the count down me is complete, the display will change to the 3 red bars and the steam generator will shut o. You may halt
your steam bath program at any me by pushing the “on/o” buon.
Quick Tips For User’s
Touch the “on” buon: displays steam room temp/temp shut o seng/me in minutes and arrows - me up/down.
Touch the “temp” buon: display changes readout to show room temperature and arrow buons change from C to F.
2nd touch ”temp” buon: display changes readout to temp shut o seng and arrows buons change - temp up/down.
Touching the “me” buon and then the “temp” buon changes the control to display the steam room temperature. For programming
instrucons see Seng Your Program, below.
SETTING YOUR PROGRAM:
NOTE: ONCE THE CONTROL IS TURNED ON AND DISPLAYS THE TIME, IT MAY BE PROGRAMMED BY PRESSING AND HOLDING THE
“me” OR “temp” BUTTON FOR MINIMUM - 5 - SECONDS. ONLY ONE BUTTON AT A TIME. - SETTINGS CAN ONLY BE CHANGED
WHEN DIGITS ARE FLASHING.
1. TIME Press and hold the “me” buon for 5 seconds unl the digits begin to ash. Press the arrow buons up or down to
increase or decrease the amount of me to program as the default for your steam visits. Touch the me buon to
lock in your seng or wait for the digits to stop ashing and automacally lock in. You have approximately 15 seconds
to complete your choice. When the control is restarted your programmed me seng will appear as the default.
2. TEMP Press and hold the “temp” buon for 5 seconds unl the display digits ash “SET” and the temperature
set point is ashing. Press the arrow buons up or down to increase or decrease the temperature seng
default for your steam visits. Touch the temp buon to lock in your sengs or wait for the digits to stop
ashing and automacally lock in. You have approximately 15 seconds to complete your choice. You have
completed programming the controls startup default sengs for me and temperature - congratulaons!
SAFETY PARAMETERS IN YOUR PROGRAM:
There are built in safety parameters in your program that you can not change. These safety controls were built in during the
manufacture and limit the me and temperature of your steam room. They control the steam room heat me, the maximum
temperature the room will reach and the length of me one steam visit should last. These parameters are automacally
reset aer each use. Maximum temperature 120 0F or 49 0C. Maximum length of steam visit for one cycle - 60 minutes.

4www.relax-a-mist.com1-800-Y-U-STEAM (1-800-987-8326)
INSTALLATION INSTRUCTIONS - TIME & TEMPERATURE CONTROL
4www.relax-a-mist.com1-800-Y-U-STEAM (1-800-987-8326)
WARRANTY POLICY
For a period of one year from the date of installaon, or 18 months from the date of manufacture, whichever comes rst, all
parts and assemblies are warranted as to workmanship and materials used in their manufacture. There is no cosmec warranty
on installed parts or controls. Any Relax-A-Mist® products containing defecve parts, if returned prepaid to an authorized Service
Depot within the one year or 18 month me limit, will be repaired free of charge, F.O.B. the authorized Service Depot making such
repairs.
The Company will not be responsible for any breakdown, damage, or losses, direct or indirect, arising in contract or in tort from
any cause whatsoever, including failure to follow the Relax-A-Mist® installaon instrucons specically, careless handling, improper
voltage supply, corrosion and/or electrolysis or a buildup of minerals on the parts or assemblies for any reason or from any source;
nor for transportaon and/or other charges incurred in the removal , replacement or repair of defecve products or parts; and
there are no warranes or condions expressed or implied or otherwise applicable, to the company’s products except as expressly
stated herein.
WARRANTY IS VOID IF RESIDENTIAL STEAM GENERATORS
ARE USED IN A COMMERCIAL INSTALLATION.
QUALITY
STEAM BATH EQUIPMEN
T
R E L A X MIST
A
®
BRITISH COLUMBIA ALBERTA ALBERTA
LEISURE BATHS LTD. FRASER-BOND LTD. LEHMANN PLUMBING
6909 Antrim Avenue 9452 Almond Crescent S.E. 3649 73 Avenue
Burnaby, BC V5J 4M5 Calgary, AB T2J 1B6 Edmonton, AB T6B 2T8
TEL [phone] TEL [phone] TEL [phone]
or 1-800-Y-U-STEAM FAX [phone] FAX [phone]
(1-800-987-8326)
FAX [phone]
MANITOBA ONTARIO QUEBEC
BALCAEN & SONS LTD. ACCORD APPLIANCE INC. THOMAS & SCHMIDT (T&S)
1392 Pembina Highway #17 - 750 Oakdale Rd. 2825 rue Sabourin
Winnipeg, MB R3T 2C1 North York, ON M3N 2Z4 Saint-Laurent, QC H4S 1M9
TEL [phone] TEL [phone] TEL [phone]
FAX [phone] FAX [phone] or 1-800-363-0708
FAX [phone]
For assistance, phone Relax-A-Mist® at 1-800-Y-U-STEAM (1-800-987-8326) or e-mail: [e-mail]
Please Note: Leisure Baths Ltd. shall not be held responsible for any errors in catalogues, brochures, or other printed material. As we are connuously improving
and developing our products, we reserve the right to alter products or introduce modicaons to the technical data at any me, without noce;
therefore, we cannot accept legal liability for the informaon given, nor for any prinng mistakes that may have occurred.
AUTHORIZED SERVICE DEPOTS
WARRANTY POLICY