Ultra Start 2500 SERIES User manual

WWW.ULTRASTARTERS.COM
2500
2500
2500M
INSTALLATION GUIDE
Advanced Remote Vehicle
Starter & Alarm
TECH SUPPORT
Western Canada 1 800 279-0636
United States: 1 866 698-5872
Eastern Canada. Bilingual Supp rt: 1 800 268-0683
E-Mail Tech Supp rt: supp [email protected] m
Check Our Web Site: www.ultrastarters.c m

Installati n Guide
2500 Wiring Diagram Page 3
Page 5
Page 6-7
Pre-Installation Page 4
C mp nents
Rec mmended Pre-Installati n Pr cedures
Rec mmended Install pr cedures
Wire Connectors
6 Pin C nnect r
14 Pin C nnect r
3 Pin Red C nnect r
4 Pin Blue C nnect r
Jumper Selecti ns
Installation
Basic Installati n - Quick start
Plugging In The M dule
Aut Tach Learn
Sh ck Sens r Pr gramming
Programming Page 7-11
Pr gram Overview & System Reset
Pr gram Menu 1 (User Settings)
Pr gram Menu 2 (Alarm Settings)
Pr gram Menu 3 (Starter Settings)
Pr gram Menu 4 (Tach Settings)
Other Features And Operations Page 12
Reservati n M de
Transmitter Pr gramming
Battery Replacement
Service m de
Rem te Service M de
Warranty
System Operation Page 14-15
Relay Diagrams Page 16
TABLE OF CONTENTS
If the rem te starter has a failed start attempt r if a safety input is activated the Diagn stic Mem ry will
st re up t f ur shutd wns in mem ry. This inf rmati n can then be accessed t determine the s urce f
the shutd wn.
To Enter Diagnostic Mode:
Step 1 - Turn the igniti n n wait tw sec nds then turn ff. Press the Pr gram Butt n and release.
Step 2 - The system will resp nd with three park light flashes and the siren will chirp the
same number f times as the events in mem ry. ( Maximum f ur events, f ur chirps)
NOTE: If the siren d es n t chirp, there are n events in mem ry.
Step 3 - Press the Pr gram Butt n nce t view the last shut d wn c de. The siren will chirp nce t
c nfirm c de ne.
Step 4 - The LED’s n the antenna will flash a c de c rresp nding t a shut d wn trigger. Press the
Pr gram Butt n again t check the sec nd c de. The siren will chirp twice t c nfirm c de tw .
Step 5 - T Clear Diagnostic Memory. While in Diagn stic M de press and h ld the Pr gram Butt n f r
five sec nds. The park lights will flash and the siren will chirp nce.
NOTE: Once diagn stic mem ry has 4 impr per shutd wn events in mem ry, the system will n t
rec rd any further shutd wn events until the system mem ry has been cleared.
(If the siren d es n t chirp, there are n c des in mem ry).
PARK LIGHTS STATUS LED DIAGNOSTIC CODE
3 Flashes Series f 3 Flashes D r Opened “M” M dels
4 Sl w Flashes Series f 4 Flashes N t in Reservati n M de “M” units
5 Flashes Series f 5 Flashes H d Pin Gr unded (Open)
6 Flashes Series f 6 Flashes Brake Pedal Shutd wn
7 Flashes Series f 7 Flashes Tach L ck-Out
8 Flashes Series f 8 Flashes 3 Start Attempts with n start
DIAGNOSTICS
2
1
3
5
2
4
6
2
1
4
3
6
5
7
8
10
9
12
11
14
13
10
12
11
13

Installati n Guide
WIRING DIAGRAM
3
1
3
5
2
4
6
2
1
4
3
6
5
7
8
10
9
12
11
14
13
10
12
11
13
4 PIN BLUE
4 PIN
RED
4 PIN
WHITE
4 PIN
WHITE
4 PIN
WHITE
SIDE VIEW
SATELLITE LINK PLUG
STARTER DISABLE. SEE PAGE. 7
RF ANTENNA WITH DUAL LED’s
& BUILT-IN VALET SWITCH
***500ma outputs are low current and are designed to activate relays
*Must be connected to operate the system
Blue
Green
Red
Red
Yellow
White / Green
White / Blue
BLK/WHT
BLK/WHT
Starter
Heater
Main Power
Ignition 1
Selecta le P.5
Main Power
RE-ARM
STARTER DISABLE
FACTORY DISARM
TRUNK RELEASE
THIRD IGNITION (-)
(-) DOOR TRIGGER
HOOD PIN INPUT
(+) DOOR TRIGGER
BRAKE PEDAL
GROUND
TACH INPUT
GLOW PLUG
PARK LIGHTS
PARK BRAKE
4th Ch. Programma le
Siren Output
Dome Light Supervision
Trunk Pin Switch Input
YELLOW
WHITE / VIOLET
BLUE/WHT
BROWN
ORANGE
GREEN/WHITE
WHITE
BLUE
GREEN
BLACK/WHITE
PURPLE
PINK
BLACK
RED/WHITE
Black
Red
White
(+) 30amp Output
(+) 30amp Output
(+) 30amp Input
(+) 30amp Input
(+) 30amp Output
(+) 30amp Output
(-)500ma Output
(-)500ma Output
(-)500ma Output
(-)500ma Output
(-)500ma Output
(-)500ma Output
(-)500ma Output
Negative Input
Negative Input
Negative Input
Negative Input
Negative Input
(A/C) Input
(-) Input
Positive Input
Positive 15amp
Positive 3 amp
Positive Input
Green
Pink
Blue
Negative When Disarmed
Horn Honk/ 5th Channel
(-)500ma Output
(-)500ma Output
(+) Input
(+)Disconnect / Start trigger
Sensor Full-Warn
Sensor Pre-Warn
Sensor Ground
Sensor 12V+ Power
Black
Red
Blue
Green
(-)Input
(-) Input
(-)500ma Output
(+)500ma Output
Door Lock
12V+ for Relays
Door Unlock
Passenger Door Unlock
Red
Blue
Pink
Green
(-)500ma Output
(-)500ma Output
(-)500ma Output
(-)500ma Output
TEMPERATURE SENSOR INPUT (OPTIONAL)
Jumper Access

Installati n Guide
Recommended Pre-Installation Procedures
- C ntr l m dule
- Rem te transmitter(s)
- Antenna with built in Pr gram Butt n and LED’s
- 6 pin main harness with dual 30amp p wer inputs
- 14 pin harness
- 4 pin square harness.
- 4 pin keyless entry harness
- 4 pin Aux. sens r harness
- Multi-t ne Siren
- H d pin safety switch
- Installati n guide
- Owners manual
BEFORE STARTING INSTALLATION:
- Discuss the pti nal features with the cust mer.
- D a walk ar und the vehicle and check f r any damage.
- If installing a LED discuss the placement with cust mer bef re installing.
Note: This remote starter is designed for fuel injected and diesel engines.
- Take a few minutes t review the installati n and wners manuals.
- Check if the vehicle has a fact ry security r anti-thieft system.
*If equipped, inf rm the cust mer f additi n parts and lab ur.
Recommended Installation Procedures
INSTALLATION TIPS
Components
Under Hood Connections - R ute the h d pin and tach wires thr ugh the firewall int the engine
c mpartment. Always try t pull the wires thr ugh a fact ry rubber gr mmet. If drilling thr ugh the
firewall, BE CAREFUL. Check f r bstructi ns n b th sides f the firewall. After drilling use a snap in
gr mmet t pr tect the wires fr m sharp edges.
Proper Connections - Rem te Starters can handle l ads f up t 30 amps f r extended peri ds f
time. It is CRITICAL t insure that ALL high current c nnecti ns are pr perly s ldered and insulated
with quality electrical tape. Failing t insure pr per c nnecti ns will result in warranty being VOID and
can result in a FIRE. The manufacturer is n t resp nsible f r any such damages. It nly takes a few
m re minutes t d the j b RIGHT.
Mounting The Control Module - Never m unt the m dule in the engine c mpartment. Select a
l cati n under the dash t install the main m dule. Be certain that the m dule is securely attached and
d es n t bstruct any serviceable areas. D n t f rce r jam the m dule int tight places instead f
m unting. The m dule must be free fr m all m ving parts such as brake, clutch and gas pedal
linkages. D n t place the m dule directly in fr nt f a heater vent.
Installing the External Long Range Antenna - T insure the best p ssible recepti n, place the
antenna in the center f the windshield, behind the rear view mirr r. Bef re attaching t the glass ensure
that the surface is clean and dry. F r best results with range, place the antenna bel w the tint screen.
Run the cable under the head liner and behind the A-pillar panel. Be careful n t t pinch the antenna
cable. Plug the antenna int the BLUE c nnect r n the C ntr l M dule.
NOTE: This step is n t used n Alarm Only Units with n External Antenna.
Testing The System - When the installati n is c mplete, it will be necessary t test that the system
is w rking c rrectly. The system’s default pr gramming will w rk n the maj rity f vehicles, but might
need t be adjusted f r s me applicati ns. If the installati n requires special timing r additi nal
features, pr ceed t Pr gram M de.
4
ATTENTION: Hood Pin MUST always be connected!!
NOTE: Always inf rm user t place system in Service M de bef re any service w rk is
perf rmed n the vehicle.

Installati n Guide
WIRING CONNECTORS
5
WIRING CONNECTORS
Yellow Starter 30amp utput 12volts during crank only.
Green Heater 30amp utput 12volts in accessory. Off during start.
Red 12 power 30amp input Constant 12volt power at ignition harness.
Red 12 power 30amp input Constant 12volt power at ignition harness.
Blue Ignition 1 30amp utput 12volts in ignition and start positions.
White Selectable 30amp utput Jumper Selectable. See Page 5.
Yellow Re-Arm 0.75sec Pulse With L ck And On Shutd wn.
Orange (-) Output Negative While L cked - **Starter Program Mode.
Brown Disarm 0.75sec Pulse With Unl ck And Bef re Start.
Red/White 3rd CH Trunk Release - Active When The Unl ck Butt n Is Held F r 3sec nds.
White/Violet (-)Running Negative Output While Running.
Green (-) D r Negative D r Trigger Input - Manual Trans And Alarm Units Only.
Purple (+) D r P sitive D r Trigger Input - Manual Trans And Alarm Units Only.
Green/White H d Pin Negative H d Pin Input - MUST BE CONNECTED!!
Pink Brake P sitive Brake Input - MUST BE CONNECTED!!
Black Gr und System Gr und Input - MUST BE CONNECTED!!
Blue/White Tach Tach Signal Input - MUST BE CONNECTED!!
Blue Gl w Plug Negative Gl w Plug Input - DIESEL ENGINE ONLY. **Starter Program Mode.
White Park Lights P sitive Park light Output - 10 Amp Max.
Black/White Park Brake Negative Park Brake Input - Manual Transmission Models Only.
6 Pin Power Connector
14 Pin Connector
5
White/Green Channel 4 Programmable- See Alarm Settings. Menu 2.
Black D me Light Negative Output F r D me Light Supervisi n.
White/Blue Siren P sitive Output F r Siren.
Red Trunk Pin Negative Input f r Trunk Pin.
Green D r L ck D r L ck Output - Programmable - Menu 1 Setting 3.
Red 12 V lts Low Current Output. Use With V ltage Inverter
Blue D r Unl ck D r Unl ck Output - Programmable - Menu 1 Setting 3.
Pink 2nd Unl ck D r Unl ck Output - Programmable - Menu 1 Setting 3.
4 Pin Connector Square
4 Pin Connector Red
Jumper Selections
3 Pin Connector White
Green (-) Disarmed Negative Output When The System Is Disarmed.
Pink H rn/5th Channel Pr grammable Output.
Blue (+) Disc nnect (+) Disc nnect Or Instant Start Trigger.
The jumpers c ntr l the utput n the white wire fr m the
six pin harness. Place the jumpers in the ab ve rder t
change the utput.
Note: The default setting is second ignition.
Output on White wire Jumper position
Second Starter Position 1
Second Accessory Position 2
Second Ignition Position 3
Back View Of Module
Jumpers
3 2 1

Installati n Guide
QUICK START INSTALL
Yellow Starter Output C nnect T The Vehicles Starter Wire.
Green Heater Output C nnect T The Vehicles Access ry Wire.
Red 12 power Input C nnect t C nstant 12 V lt P wer S urce- High Current.
Red 12 power Input C nnect t C nstant 12 V lt P wer S urce- High Current.
Blue Ignition 1 Output C nnect T the Vehicles Primary Igniti n.
White Selectable Output Select Jumper P siti n (If Necessary). See Page 5.
6 Pin Power Connector
14 Pin Power Connector
Manual Transmissions Only
Step 2- Plug-In The Module
Step 3- Auto Tach Learn
Your Basic Install Is Complete!
Step 1 - Connect All Of the Following Wires
Black/White Park Brake Connect (-) Parking Brake
Manual transmissi n vehicles must have a “M” Series Rem te Starter Installed. Manual Transmissi n
Units Must Be Placed Int Reservati n M de T Operate. See Page 10.
Your Basic Installation is Now Complete!!
1) Make all the required wire c nnecti ns and plug-in the Unit.
**The park lights sh uld flash twice up n p wer up.
2) Turn the Igniti n Key ON. (Park Lights will turn n).
3) Start the vehicle, LED’s n the antenna will c me n t c nfirm tach signal is detected**, then after tw
t ten sec nds the park lights will turn ff then flash twice t c nfirm tach learning.
* The system will flash the park lights seven times if not tach learned and the start button is
pressed. The system must be tach learned before remote starting.
** If the LED’s do not come on during tach learn, a proper tach signal was not detected.
Note: If the park lights d n t flash in aut tach learn m de it may be necessary t c nnect t a different
tach s urce. F r best results c nnect the tach wire t the c il pack r t a fuel inject r wire. If necessary
See Page 11. for Tach Adjustment.
NOTES:
1) If the unit does not start, check the starter is not in Tach Lock Out or in Program Mode.
2) If the vehicle still does not start, check all connections and check for factory security.
When all the c nnecti ns are d ne, the c ntr l m dule can be plugged in. Bef re c nnecting the c ntr l
m dule, make sure the igniti n is in the OFF p siti n. Plug in the 6 pin harness then the 14 pin f ll wed
by any ther c nnect rs that were used.
6
Black System Ground C nnect T Chassis Gr und.
Pink Brake Switch C nnect T (+) When Brake is Applied.
White Park Lights C nnect T (+) Park Light System.
Green/White Hood Pin C nnect T H d Pin Switch.
Blue/White Tach C nnect T Tach S urce.
White/Blue Siren / Horn C nnect T (+) Siren r H rn.
Green or (-) Door Input C nnect the Green wire t a (-) d r pin system.
Purple (+) Door Input C nnect the Purple wire t a (+) d r pin system.
Activate Self Learning Impact Sensor
1) Press the LOCK butt n n the rem te 5 times in a r w. The siren sh uld chirp 3 times and the park
lights sh uld c me and stay ON.
2) While the park lights are n, strike the vehicle at the desired level t trigger the alarm.
3) The siren will resp nd with ne chirp t c nfirm that the Sh ck Sens r is pr grammed.
4) Press the l ck r unl ck butt n t exit Sh ck Sens r learning.

Installati n Guide
Pr gram m de all ws y u t adjust the settings and pti ns f y ur system.
Menu 2 - Alarm Settings - Page 9
This pr gram menu c ntains settings that adjust the way the system perates f r the user.
Y ur system has been intelligently designed by installers with years f experience. The system’s default
settings d n t require any pr gram changes in m st cases. H wever, this system d es inc rp rate a highly
advanced pr gramming system that includes 4 menus with numer us pti ns and settings that can be easily
adjusted f r cust m installati ns and applicati ns.
Menu 1 - User Settings - Page 8
This pr gram menu c ntains settings that adjust the way the system perates f r the user.
Menu 3 - Starter Settings - Page 10
This menu c ntr ls features and settings ass ciated with rem te car starter applicati ns.
Menu 4 - Tach Settings - Page 11
This menu all ws the pr gramming f the tach signal and the manual adjustment f that setting.
Programming Overview
Entering Program Mode
Changing the Programmable Settings
To Enter Program Mode
1) Make sure igniti n is in the ff p siti n.
2) Within three sec nds turn the key ON - OFF - ON - OFF - ON. Leave in the “ON” position.
3) Press and release the Pr gram Butt n n the antenna ne time.
4) The park lights will c me n and the siren will chirp t c nfirm entering Pr gram M de.
5) Select the Desired Pr gram Menu:
Note: If unit does not enter Program Mode, turn the ignition off for five seconds and repeat steps 1-4.
** The first igniti n(Blue wire) MUST be c nnected t the vehicle’s first igniti n wire. If it is n t
c nnected it will n t be p ssible t enter the Pr gram M des.
Press Button #1 Lock User Options Page 8
Press Button #2 Unlock Alarm Option Page 9
Press Button #3 Start Remote Start Options Page 10
Press Button #4 Aux Tach Adjustment Menu Page 11
6) The selected m de will be c nfirmed by a siren chirp and ne park light flash.
7) The Pr gram Menu may be changed at any time by pressing the transmitter butt ns as ab ve, this
all ws the installer t change a setting fr m ne menu, then quickly jump t an ther menu and
change an ther setting with ut re-entering the Pr gram M de.
8) T exit Pr gram M de, Turn the igniti n key “OFF” r wait 30 sec nd and the system will exit
aut matically. This will be c nfirmed by ne l ng siren chirp and park light flash.
To Select and Change A Program Setting:
1) Enter Program Mode.
2) Select the desired Program Menu. (See pages 8 - 11)
3) Press & release the Program Button the c rrect number f times t select the desired Pr gram
Setting(as listed on pages 8 - 11). The park lights will flash and the siren will chirp t indicate the current
setting that is selected.
4) Press and h ld the Pr gram Butt n until the parking lights / siren c nfirm the selected setting. The
park lights will flash and the siren will chirp t indicate the pti n selected within the setting.
5) Turn the igniti n key “Off” t exit Pr gram M de.
NOTE: This pr cedure is listed in detail bel w each pr gram setting n pages 8 - 11 f this manual.
PROGRAMMING
STEP 1 - Within three sec nds turn the key ON-OFF-ON-OFF-ON (Leaving Key ON).
STEP 2 - Press and release the Pr gram Butt n.
STEP 3 -The park Lights will turn ON.
STEP 4 - Press the Pr gram Butt n a sec nd time and h ld f r 8 sec nds until the park lights flash
and the siren will chirps three times.
The system is now re-set to factory defaults.
NOTE: Reset t defaults d es n t delete the transmitters fr m mem ry.
SYSTEM RESET
7

Installati n Guide
PROGRAMMING
8
PROGRAM MODE - USER SETTINGS
Enter User Program Mode - See Page 7 for details on entering program mode
1 Double Pulse Unlock 1 Flash Single .75sec.Lock pulse and double Unlock Pulse
2 3 Second Lock & Unlock 2 Flashes 3 second pulses for Lock & Unlock
*3 0.75 Second Pulses 3 Flashes 0.75 second pulses for Lock and Unlock
1 Ignition Lock & Unlock Enabled 1 Light Flash Doors Lock / Unlock when the key is turned On/ Off
2 Ignition Lock Only 2 Light Flashes Doors Lock when ignition key is turned ON only
*3 Ignition Auto Lock Disa led 3 Light Flashes Doors do not Lock or Unlock with Ignition key
1 Lock & Unlock chirps Disa led 1 Flash Honks for Panic and Car Finder Mode only.
2 Lock & Unlock chirps Ena led 2 Flashes Honks for Lock, Unlock, Panic and Car Finder Mode Only.
*3 All chirps ena led 3 Flashes Honks for Lock, Unlock, Start, Panic and Car Finder Mode.
Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 4 times to select setting 3 (This will be confirmed by 4 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change
Setting 1- Ignition Auto Lock
Setting 2- Horn Honk Settings
Setting 3- Door Lock Options
Setting 4 -Sensor - Enable / Disable
1 Sensors Disabled 1 Flash Impact Sensors Disabled
* 2 Sensors Ena led 2 Flashes Impact Sensors Ena led - Normal Operation
Press the Program Switch 5 times to select setting 1 (This will be confirmed by 5 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 6 times to select setting 1 (This will be confirmed by 6 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
1 Passive Arming 1 Flash System Auto Arms 30 seconds after last door is closed
2 Active Arming With Rearm 2 Flashes System Auto-Arms if unlock is pressed and no door is opened within 30sec
* 3 Active Arming 3 Flashes Alarm Arms Only with Transmitter
1 No Auto-Lock with Passive Arm 1 Flash Doors do not auto-lock with passive arming
*2 Doors Auto-Lock with Passive 2 Flashes DOORS LOCK WHEN PASSIVE ARMING
Setting 5 - Passive / Active Arming
Setting 6 - Active / Passive Locks

Installati n Guide
PROGRAMMING
9
PROGRAM MODE - ALARM SETTINGS
Setting 1 - Car Finder / 5th Channel
Setting 2 - Secure Valet Mode
Setting 3 - Parking Light Output
Setting 4 - Horn Honk Timing - Pink wire on 3-pin white
Setting 5 - 4th Channel Settings- White/Green on 4-pin square
Setting 6 -Car Jack ModeSetting 6 -Car Jack ModeSetting 6 -Car Jack Mode
Setting 7 - Horn / 5th Channel
Enter Alarm Program Mode - See Page 7 for details on entering program mode
Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Proram Switch until you receive the appropriate # of park light flashes and/or horn honks
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 4 times to select setting 3 (This will be confirmed by 4 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 5 times to select setting 1 (This will be confirmed by 5 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 6 times to select setting 1 (This will be confirmed by 6 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
1 Pulsed 1 Flash Pulsed for 0.75 seconds upon 4th Channel Activation
2 Latched 2 Flashes Latched until repeated or ignition “ON”
*3 Active 3 Flashes Active for as long a utton is held on Transmitter as long as held
1 Door & Button 1 Flash Car Jack is activated upon Button 4 or Door open while Ignition is “ON”
2 Door, Button 4 2 Flashes Car Jack is upon Button 4 or Door open or ignition “ON” and Ignition
*3 Car Jack OFF 3 Flashes No Car Jack Functions
1 5th Channel 1 Flash Pulsed output when activated by button #4
2 Horn Honk 2 2 Flashes Horn Honk Output - Full Alarm ONLY
*3 Horn Honk 1 3 Flashes Horn Honk with Arm & Disarm Chirps
1 Car Finder OFF 1 Light Flash Car Finder Mode Disabled
*2 Car Finder ON 2 Light Flashes Car Finder Mode Ena led
Note: To operate the 5th channel on utton #4, setting 7 must e programmed for 5th channel output.
1 30 Second Parking Lights on Disarm 1 Flash Park Lights on for 30 seconds on disarm
2 Negative Park Light 2 Flashes Switches the Park Light and the Trunk Release (3rd Channel) Outputs
3* Normal Parking Lights 3 Flashes 2 Park Light Flashes on disarm
1 5ms 1 Flash Short (Quiet) Pulses
2 20ms 2 Flashes Long (Loud) Pulses
*3 10ms 3 Flashes Normal (Medium) Pulses
1 Secure Valet Active 1 Flash Valet only if ignition “ON” and valet switch held for 15 seconds
2* Normal Valet Active 2 Flashes Valet if ignition “ON” and valet switch held for 5 seconds
Press the Lock and Start uttons together to activate the 4th Channel Output.

Installati n Guide
Press the Program Switch 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and siren chirps..
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 7- Sensor Disconnect
10
1 Positive Input To Start 1 Flash Positive pulse will activate remote starter.
2 Positive Disconnect 2 Flashes Alarm will trigger if disconnected from 12 volts.(Same as below)
3* Positive Disconnect 3 Flashes Alarm will trigger if disconnected from 12 volts.
PROGRAM MODE - STARTER SETTINGS
Enter Starter Program Mode - See Page 7 for details on entering program mode
1 Chrysler / VW Re-Arm 1 Flash Unlock pulse before start and a lock pulse after start
2 GM Auto Re-Lock 2 Flashes Lock pulse after remote starter shuts off
3* Normal Operation 3 Flashes No additional re-lock pulses
1 Diesel Glow Plug 1 Flash W
2 Timed Delay 2 Flashes Ignition ON for 10 seconds before engaging remote starter
3* Gas Mode operation 3 Flashes Waits 2 seconds efore engaging starter output
aits a Maximum of 3:20 second before starting.
1 Type 1 1 Flash Pulse after start and with lock
2 Type 2 2 Flashes Pulse after start only
3* Factory Re-arm 3 Flashes 0.75 second pulse with lock and after shutdown
Setting 1- Special Door Lock/ Unlock Operations
Setting 2- Gas/ Diesel Mode- Blue Wire n 14-Pin
Setting 3- Rearm Output- Yell w Wire n 14-Pin
1 30 Min Run Time 1 Flash Remote Starter runs for 30min when activated
2 45 Min Run Time 2 Flashes Remote Starter runs for 45min when activated
3* 15 Min Run Time 3 Flashes Remote Starter runs for 15 min when activated
1 10 Seconds 1 Flash 10 sec Max time that starter will stay engaged
2 3 Seconds 2 Flashes 3 sec Max time that starter will stay engaged
3* 5 seconds 3 Flashes 5 sec Max time that starter will stay engaged
Setting 4- Run Time
Setting 5-Maximum Crank Time
Setting 6- Sensor Disconnect
1 Positive Input To Start 1 Flash Positive pulse will activate remote starter.
2 Positive Disconnect 2 Flashes Alarm will trigger if disconnected from 12 volts.(Same as below)
3* Positive Disconnect 3 Flashes Alarm will trigger if disconnected from 12 volts.
Continued on next page...
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.

Installati n Guide
1 Safety ON 1 Flash Must press the start button twice to remote start vehicle
2* Safety OFF 2 Flashes Press the start utton once to remote start vehicle.
Press the Program Switch 8 times to select setting 8 (This will be confirmed by 8 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 8- Safety Start Mode
PROGRAM MODE - TACH SETTINGS
Setting 1- Method 2- Low Idle Tach Learning
Setting 2- Adjust For Over-Crank
Setting 3- Adjust For Under-Crank
Anti Car Jacking Mode
Step 1 - Enter Pr gram M de (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Pr gram M de 4 - Press the # button on the remote.(Button #4).
Step 3 - Start Vehicle - Using the ignition key, make sure not to turn the key off at any time or your will exit programming.
Step 4 - Press the Butt n - One time (Led will start flashing in single cycles) then press and hold Program (5sec).
Step 5 - Release Pr gram - Led should come on steady to indicate correct tach signal the park light will flash to confirm.
Step 1 - Enter Pr gram M de (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Pr gram M de 4 - Press the # button on the remote.(Butt n #4).
Step 3 - Press the Pr gram Butt n - 2 times (Led will start flashing 2 times).
Step 5 - Release Pr gram - Exit Pr gram M de and rem te start t test.
Step 4 - Press and H ld Pr gram - For 5 seconds until parking lights flash (each time lights flash tach is reduced 5%).
Step 1 - Enter Pr gram M de (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Pr gram M de 4 - Press the # on the remote.(Button #4).
Step 3 - Press the Pr gram Butt n - 3 times (Led will start flashing 3 times).
Step 5 - Release Pr gram - Exit Pr gram M de then rem te start t test.
Step 4 - Press and H ld Pr gram - For 5 seconds until parking lights flash (each time lights flash tach is increased 5%).
When activated, the system waits 30 sec nds then flashes LED rapidly f r 30 sec nds, then chirps
siren as a warning f r 10 sec nds then g es int full alarm .
ACTIVATING CAR JACK MODE- Pr grammable - Menu 1, Setting 5.
Activates up n any f the f ll wing steps:
- M de 1 & 2 While igniti n is “ n” press & release # butt n.
- M de 1 & 2 Open d r while igniti n is “ n”.
- M de 2 nly Each time igniti n is turned “ n”
DEACTIVATING CAR JACK MODE
1. During c untd wn peri d - Turn the igniti n “On” then press and release the antenna butt n.
2. After the alarm has activated - Turn the igniti n “Off then On” then press and h ld the
antenna butt n f r 8 sec nds .
ENSURE THAT USER IS FULLY TRAINED ON THIS FEATURE!
ONLY USE THIS FEATURE WHEN SPECIFICALLY REQUESTED. ENSURE THAT USER IS TRAINED
ON THE OPERATION OF THIS FEATURE IF NOT, UNWANTED RESULTS MAY ARISE.
11
This pti n is used f r vehicles that maintain a high r erratic idle after starting and need m re that 10
sec nds t establish a stable idle.
See page 6 for Auto Tach Learning

Installati n Guide
OPERATIONS
Manual Transmissi n Rem te Starters must have b th the d r trigger and park brake wires c nnected. M st
installs will require a clutch bypass. This is a temp rary bypass. The clutch sh uld nly be bypassed during
the activati n f the rem te starter. Never disc nnect r alter the switch t be always bypassed. Always use a
“M” Series Rem te Starter n a manual transmissi n vehicle.
Never install a aut matic Rem te Starter m del int a manual transmissi n vehicle. It is n t rec mmended t
install a rem te starter n a c nvertible type vehicle. If d ing s It is highly rec mmended that a radar sens r
is installed t c ver the pr ximity f the gear shift lever. If the radar sens r is tripped the rem te starter will exit
Reservati n M de.
To enter Reservation Mode, the following steps must be followed.
Step 1 - While the vehicle is running, place the transmissi n in neutral and apply the parking brake.
Step 2 - Press and release the brake pedal. The park lights will activate.
Step 3 - Turn the igniti n key ff and the vehicle will stay running.
Step 4 - Exit the vehicle and cl se the d r. The vehicle will then shut ff.
Step 5 - The vehicle can n w be safely rem te started.
Reservati n M de will aut matically be exited if the d rs f the vehicle
are pened. The set-up m de will then have t be repeated . Reservati n M de Must be set-up each time the
vehicle is parked.
Note: If the vehicle is not in Reservation Mode and the Start button is pressed, the system will flash
the park lights four times slowly.
NOTE: If the vehicle has a d me light delay, the vehicle may stay running until the d me light turns ff. This is
n rmally n l nger than 30 sec nds.
Reservation Mode - Manual Trans.
Step 1 - Within three sec nds turn the igniti n Key ON-OFF-ON-OFF-ON - Leaving Key ON
Step 2 - Press and h ld the Pr gram Switch - Parking Lights will c me ON **if park-lights d n t c me
n at this p int, turn key ff f r 5 sec nds, the repeat step 1.
Step 3 - C ntinue t h ld the Pr gram Switch until park lights g ut.
Step 4 - Press the LOCK butt n n each f 1st car rem tes and press the # butt n n each f the 2nd
car rem tes f the transmitters t be pr grammed. The park lights will flash nce and the h rn
will h nk nce each time a new c de is learned.
Note: Transmitter pr gramming must d ne quickly. D n t pause m re than ne sec nd between each
transmitter. All the transmitters t be used must be pr grammed at the same time. All transmitters
not programmed at this time will be erased from memory for security. The system holds a
maximum of 3 transmitter codes including 2nd car remote codes.
Y u can pr gram the same rem te as a 1st car rem te in ne vehicle and as a 2nd car rem te in a
sec nd vehicle.
+
-
Step #1 Step #2
Step #3 Step #4
Carefully rem ve the
screw fr m back f
the rem te.
Rem ve t p case
then replace the
battery.
Replace t p case.
Re-install screw.
Test rem te f r
pr per perati n.
The transmitter attery should e changed at least once every year to maintain proper operating range.
Replace with quality23A 12volt Alkaline attery.
Transmitter Programming
Battery Replacement
12

Installati n Guide
OTHER FEATURES
ACTIVATING SERVICE MODE
1. While the igniti n is “ON” press and h ld the Pr gram Butt n f r five sec nds. The
park lights will flash and the siren will chirp five times t c nfirm that the system is in
Service M de.
2. While in Service M de the rem te start functi ns will be disabled and LED’s will be
“ON” steady. D r l cks and trunk release are still perati nal.
DEACTIVATING SERVICE MODE
1. While the igniti n is “ON” press and h ld the Pr gram Butt n f r five sec nds. The
park lights will flash and the siren will chirp tw times t c nfirm that the system has
exited Service M de.
2. Rem te start functi ns will return t n rmal perati n.
System Service Mode
Service Mode- By Remote
SERVICE MODE ACTIVATED
1 - Press & Release butt n 4
2 - Press & H ld Butt n 4 f r 6 sec nds until Status LED c mes n Steady
NOTE: The siren will chirp 5 times as confirmation.
SERVICE MODE DEACTIVATED
1 - Press & Release butt n 4
2 - Press & H ld Butt n 4 f r 6 sec nds until Status LED turns ff.
NOTE: The siren will chirp 2 times as confirmation.
13
WARRANTY- Optional Three year & lifetime warranty available. See Dealer For Details.
The manufacturer warrants t the riginal purchaser f their rem te starters and alarms, that the pr duct shall be free fr m
defects in material and w rkmanship. H wever, sh uld this pr duct be pr ven t be defective, within a tw year peri d fr m
the riginal date f purchase, the manufacturer will, with ut charge t the purchaser (excluding any charges incurred t
have the pr duct delivered t the manufacturer) , repair r replace any part f the rem te starter and/ r alarm which the
manufacturer agrees t be defective. All warranties apply n t the riginal purchaser and the vehicle in which it is
riginally installed. Repairs r replacement f defective m dules shall remain at the discreti n f the manufacturer. All ther
parts, c mp nents, access ries and/ r pti nal equipment pertaining t the rem te starter and alarm are n t included in
the manufacturer’s warranty. This warranty is non-transferable. Request f r warranty service fr m any Fact ry
Auth rized Dealer must be accompanied with the original purchase receipt or have product registered by
authorized dealer on manufacturer’s website. Failure t c mply with any f these c nditi ns may result in warranty
being v ided.
This warranty d es n t c ver the f ll wing: rem val and reinstall lab ur charges, shipping charges, abuse, misuse, r
accidental damages t the rem te starter and alarm, aut m bile, and/ r parts there f. This warranty is v id up n
m dificati n, repairs, r alterati ns f any part f the System. The manufacturer d es n t guarantee r insure against theft
f the vehicle r its c ntents. Alarm m dels are designed nly t act as a deterrent against p ssible theft. This alarm may
qualify f r aut insurance disc unts, c ntact y ur Insurance Agent f r further inf rmati n . The manufacturer shall n t be
held liable f r any c nsequential damages due t breach f this r any ther warranty, expressed, r implied. This warranty
gives y u specific legal rights. Y ur specific legal rights may vary f r each regi n.
CERTAIN DAMAGES EXCLUDED - The manufacturer expressly disclaims any liability r resp nsibility f r
incidental damages caused by the pr duct, including ec n mic l ss, l ss f use f the pr duct, car rentals, r any ther
c sts relating t the care and cust dy f the pr duct. The manufacturer disclaims liability r resp nsibility f r any
c nsequential damages caused by the pr duct r resulting fr m its use, including the c st f repairing r replacing ther
pr perty damaged by the pr duct r caused by its use, whether r n t the pr duct is w rking pr perly. The pr duct is
intended t deter unauth rized use f the vehicles in which it is installed. The manufacturer d es n t warrant that the
pr duct is f l-safe against theft and/ r vandalism and/ r human err r r misuse. The manufacturer accepts n liability r
resp nsibility f r any damage f any kind whats ever caused t any vehicle in which the pr duct is installed r any resulting
damage fr m its use. The manufacturer accepts n resp nsibility r liability f r any damage resulting t r theft f the
vehicle r its c ntents, caused r alleged t be caused, directly r indirectly, by failure f the pr duct.

Installati n Guide
14
1. Press and h ld the # butt n f r tw sec nds.
2. The system will flash the park lights and chirp the siren five times.
**This feature can help find y ur vehicle in a cr wded parking l t.
2
sec.
1. Press and h ld the UNLOCK butt n f r three sec nds.
2. The d rs will unl ck, c ntinue h lding the unl ck butt n f r three m re sec nds, the
trunk release will then activate. The trunk release will be c nfirmed by ne park light flash.
3. F r safety reas ns, the trunk release utput will n t activate when igniti n key is in the
“On” p siti n.
3sec.
1. Press & release the LOCK butt n n the rem te transmitter.
2. The park lights will flash and the siren will chirp nce.
3. The d rs will l ck.
4. The LED will start flashing within five sec nds.
1. Press & release the UNLOCK butt n n the rem te transmitter.
2. The park lights will flash and the siren will chirp twice.
3. The d rs will unl ck.
4. The LED will st p flashing.
1. Press & h ld the LOCK butt n f r three sec nds.
2. The park lights will flash and the siren will activate.
PANIC MODE DISABLE
1. Press LOCK butt n t disable the panic m de and t l ck the d rs.
2. Press UNLOCK butt n t disable the panic m de and unl ck the d rs.
3. Panic M de will stay activated until disabled by the rem te transmitter.
3 sec.
1. Press & release the LOCK & UNLOCK butt ns at the same time.
2. If the d rs are l cked this will unl ck the d rs with ut siren chirps, the park lights
will flash tw times t c nfirm the d rs have unl cked.
3. If the d rs are unl cked this will l ck the d rs with ut siren chirps, the park lights
will flash ne time t c nfirm they have l cked.
Together
Lock Doors & Arm The Alar m
Unlock Doors & Disarm The Alar m
Silent Arm And Disarm
Trunk Release
Car Finder Mode
Panic Mode
Press Once t L ck D rs. C ntinue t h ld f r Panic M de.
Press 2nd Time & H ld f r C nstant L ck Output
Press Once f r Unl ck D rs and Disarm the Alarm.
Press & H ld f r Trunk / Aux Output
Press Once f r Start - (2 Times if programmed for safety start)
Press & H ld f r 3 sec nds while running t turn ff
Press & Release then press START and h ld f r Timer M de
2nd Car Operation
2nd Car
=
=
=
=
&&
&
&
&
&
Then
OPERATIONS

Installati n Guide
Remote Start
Remote Stop
Idle Mode
Timer / Optional Temp Start
Delay Dome Light - Auto Detection
Ignition Auto Locks
1. Press & release the butt n.
2. The Park lights will flash and the siren will chirp nce.
3. When the vehicle has started, the system will flash the park lights f ur times and
then remain “On” while the vehicle is running.
4. The vehicle will c ntinue t run f r the pr grammed runtime. (n rmally 15 minutes).
EXTEND RUNTIME
1. Press & release the butt n while the vehicle is running.
2. The system will resp nd with ne park light flash and ne siren chirp t c nfirm
Extended Runtime. The system will reset the run time, (n rmally 15 minutes).
3 sec.
1. Press and h ld the butt n f r three sec nds. The rem te starter will shut d wn.
2. The park lights will flash tw times and the siren will chirp tw times.
Note: Pressing the brake pedal r pening h d will als st p the vehicle.
1. While the vehicle is running with key, press the butt n.
2. The park lights will turn n and the siren will chirp nce.
3. Turn the igniti n key “ ff” and the vehicle will c ntinue t run.
4. Exit the vehicle and leave it running safely with ut the keys in the igniti n. L ck the
d r while the vehicle is left running.
While
running
1.Press & release the #butt n, then press and h ld the butt n f r six sec nds, until the
parking lights turn “ n”.
2. While the parking lights are “ n” the start cycle can be selected.
1 h ur cycle r 0C Press LOCK butt n 1 flash
2 h ur cycle r -5C Press UNLOCK butt n 2 flashes
3 h ur cycle r -15c Press butt n 3 flashes
4 h ur cycle r -25c Press butt n 4 flashes
3. System will start vehicle at selected cycle f r up t 24 h urs.
4. The temp start must have the temp sensor installed and will only trigger 1 time each 2 hours
if the sensor is not installed the unit will activate the timer mode.
TO CANCEL COLD START MODE
1. Press & release the #butt n, then press and h ld the butt n f r f ur sec nds.
2. The park lights will flash and the siren will chirp twice.
1st
2nd-6 sec
Ignition
On/Off
This safety feature will l ck the vehicles d rs tw sec nds after the Igniti n is turned
t the n p siti n. When the igniti n key is turned t the ff p siti n the d rs will
unl ck.
Note: The system can be pr grammed f r Igniti n L ck nly. In this setting the d r’s
will l ck when the key is turned “On” and stay l cked when the key is turned “Off”.
#
15
OPERATIONS
If the vehicle is equipped with a fact ry delay d me light, the system will detect this when arming and
chirp the siren 4 times 15-30 sec nds after arming. This c nf rmati n will als be activated if the
system is armed with the d r pen.

Installati n Guide
RELAY DIAGRAMS
16
Blue
Green
L ck
Un
l ck
Vehicle
L ck/Unl ck
Switch
T C ntr l
Relay r
Actuat rs
87
86 85
87a
30
87
86 85
87a
30
L ck
Un
l ck
Vehicle
L ck/Unl ck
Switch
T C ntr l Relay
r Actuat r
Green
Fused +12V
Blue
87
86 85
87a
30
87
86 85
87a
30
Blue
Green
L ck
Un
l ck
Vehicle
L ck/Unl ck
Switch
T Actuat r
Fused +12V
x
x
Cut Cut
DIAGNOSTICS
87
86 85
87a
30
87
86 85
87a
30
Blue
Green
L ck
Un
l ck
T Vacuum
Pump
Fused +12V
x
Cut
Gr und
Positive Type Door Locks
Negative Door Locks
5 Wire / Reverse Polarity Type Door Locks
Vacuum Type Door Locks
Built-in Starter Disable
Start
IG1
IG2
ACC
Off
T Starter M t r
r Relay
x
Cut
Starter Disable Harness
Brown wire with spade
connectors.
Note: Connect the Starter Wire (Yellow)
to the starter motor side of the starter
disable.