Ultra Fusion HZ Wine Wall User manual

Plug & Play. Line up the faceplate and backer panel holes then proceed
to secure the faceplate using the provided Ultra PEGs.
Congratulations! You have completed your Fusion Wine Wall Panel
installation. Now it’s time to pop a cork, sit back, and admire your handy
work.
ULTRA FUSION HZ WINE WALL (3FT) INSTALLATION GUIDE
Important! Before installing Pegs do the following:
1. Check the Package Contents for missing or damaged items
Contact Customer Service at 1-800-611-8644 for questions or concerns
Recommended Fastner Applications:
Drywall anchors (included) - Use for installing rails to drywall if studs are not present in
the desired location. Do not use drywall anchors to secure into a wall stud location.
Wood Screws (included) - Use wood screw to secure wall studs or wood panels, do
not use on drywall without securing to a stud. Concrete or Masonry applications not
provided.
Concrete, Brick or Stucco (Not Included) - 3/16” x 1-1/4” Masonry Screw
or #8x1-1/4” screw with the proper concrete anchors.
Package Contents
Recommended Installation Tools
(Not Included)
18x pegs 6x Wood Screws 6x Drywall anchors 1x Face plate 1x Backer Panel
Power Drill Power Bit Level Pencil Screwdriver Tape Measure
STEP
06
STEP
07
FUSION

Use a stud nder map mounting locations. Then proceed to trace a level
guideline to use as a guide of where to place your panel.
Place backer panel against wall in
desired location.
Use a level and 1/8” drillbit to mark
mounting holes, and drill the pilot
holes.
Drill drywall anchors into wall then mount backer panel with wood screws;
if not mounting into drywall, directly secure the panel into stud with wood
screw.
Remove protective lm from the faceplate. (If applicable)
STEP
01
STEP
03
STEP
05
STEP
02
STEP
04
INSTALLATION
INSTRUCTIONS

Plug & Play. Line up the faceplate and backer panel holes then proceed
to secure the faceplate using the provided Ultra PEGs.
Congratulations! You have completed your Fusion Wine Wall Panel
installation. Now it’s time to pop a cork, sit back, and admire your handy
work.
ULTRA FUSION HZ WINE WALL (4FT) INSTALLATION GUIDE
Important! Before installing Pegs do the following:
1. Check the Package Contents for missing or damaged items
Contact Customer Service at 1-800-611-8644 for questions or concerns
Recommended Fastner Applications:
Drywall anchors (included) - Use for installing rails to drywall if studs are not present in
the desired location. Do not use drywall anchors to secure into a wall stud location.
Wood Screws (included) - Use wood screw to secure wall studs or wood panels, do
not use on drywall without securing to a stud. Concrete or Masonry applications not
provided.
Concrete, Brick or Stucco (Not Included) - 3/16” x 1-1/4” Masonry Screw
or #8x1-1/4” screw with the proper concrete anchors.
Package Contents
Recommended Installation Tools
(Not Included)
24x pegs 6x Wood Screws 6x Drywall anchors 1x Face plate 1x Backer Panel
Power Drill Power Bit Level Pencil Screwdriver Tape Measure
STEP
06
STEP
07
FUSION

Use a stud nder map mounting locations. Then proceed to trace a level
guideline to use as a guide of where to place your panel.
Place backer panel against wall in
desired location.
Use a level and 1/8” drillbit to mark
mounting holes, and drill the pilot
holes.
Drill drywall anchors into wall then mount backer panel with wood screws;
if not mounting into drywall, directly secure the panel into stud with wood
screw.
Remove protective lm from the faceplate. (If applicable)
STEP
01
STEP
03
STEP
05
STEP
02
STEP
04
INSTALLATION
INSTRUCTIONS