UNEEK SJ-FB-S12-ASMO User manual

All our products are designed and manufactured right here in Australia, allowing us to have
better lead times and better quality control than companies manufacturing overseas. By
supporting us you’re supporting to grow the Australian economy and our brand.
We do not design our bars to look the same across the vehicle range. We fully develop our
own product to individually suit each vehicle. We take time in designing from scratch and
then test all our bars to comply with all relevant ADRs and Australian Standards.
Having a steel bar doesn’t mean you have to add more weight than is required to the front
of your vehicle. Our engineering practises ensure we have the right protection, designed the
right way to ensure protection is at its maximum and weights at its minimum.
We take our products out and test them right here in the heart of our country in our
Australian conditions so we know our products can withstand anything you throw at them.
Our bars are designed to give you the best advantage while off road, with increased
approach angles means you can tackle those tough and steep angles better than you could
with the original setup or other alternatives.
Uneek 4x4 back itself as Australias leading steel bull bar manufacturer. This is why we
provide you with the best steel bar warranty in Australia - 5 years.

PLEASE READ BEFORE INSTALLATION.
•When installed in accordance with these instructions winch bumpers do not affect the operation of
the vehicles SRS airbags.
•This product must be installed exactly as per these instructions using only hardware supplied.
•Take a few moments to read instructions thoroughly before beginning work.
•In the event of damage to any bar component please contact Uneek 4x4 in regards to
repair/replacement of components.
•Do not use this product for any vehicle make or model other than that specified on these
instructions.
•Do not remove labels from this product.
•This product and its fixings must not be modified in any way unless stated in these fitting
instructions.
•The installation of this product is recommended for trained personnel.
•These instructions are correct at time of publication. Uneek 4x4 cannot be held responsible for the
impact of any changes subsequently made by the vehicle manufacturer.
•During installation it is the duty of the installer to check correct operation/clearances of all
components.
•Installation time: 1 hour.
•Vehicle specific notes: Will not suit vehicles with factory bonnet scoop. If using roller fairlead a flip
up license plate kit will be required.
FASTENER TORQUE SETTINGS:
M6 –9Nm (4lb ft)
M8 –22Nm (16lb ft)
M10 –44Nm (32lb ft)
M12 –77Nm (57lb ft)
TOOLS REQUIRED:
Drill and drill bits.
EYE & EAR PROTECTION REQUIRED
DRILLING REQUIRED
TWO PERSON LIFT REQUIRED
TORQUE SETTING
CUTTING OR GRINDING REQUIRED

Remove original bumper including small brackets
shown by arrow.
Remove clips holding section shown of plastic
inner guard. Using a sharp knife or hacksaw cut
this section away only.
Place mounting brackets on chassis and mark holes for drilling. RH
side shown.
Drill marked holes out to 5mm through both sides of
each rail.

Using a drill bit or step drill open the outer chassis holes only to
10.5mm. Paint when done. RH side outer shown.
Using a drill bit or step drill open the inner chassis rails holes
to 18mm. Paint when complete. LH side inner shown.
Attach brackets to chassis using long M10 bolts, spring
washers, two flat washers per bolt, M10 nuts and crush
tubes slid into the chassis from the inner holes. Note:
Place the bolts through the hole first then slide the crush
tubes over them. Secure the front points using M8 bolts,
spring washers, flat washers and M8 flange nuts on the
inside of chassis flange. Leave loose. RH side shown.
If installing a winch do so now keeping the clutch handle in an
area as shown. Install optional license plate light (Narva 90862)
at this stage also. Please refer to winch owner’s manual in
regard to rotating handle position.
10MM
8MM
Forward

With the help of another person lift bar onto mounts
and loosely secure using M10 x 30 bolts, spring
washers, two flat washers and M10 nuts per hole.
Note: If the vehicle has a body lift raise the bar up
until all three holes line up with top holes of chassis
bracket. Once this is done adjust bar to a suitable
position (10-15mm from guard) and tighten bar bolts.
M10-44Nm
Tighten all chassis bracket bolts EXCEPT lower M10
chassis bolt.
M10-44Nm M8-22Nm
Remove nuts and washers from lower M10 bolts
and place the end of the bolt flush with the
chassis rail. Slide air deflector into position and
push M10 bolts through lower holes. Secure to
bar using M8 button head cap screws and M8
flat washers. Tighten all bolts when done.
M10-44Nm M8-22Nm
Fit license plate to vehicle. If no winch is fitted place
license plate over winch recess. If a Hawse fairlead is
fitted mount license plate above recess (a slim line is
recommended). If using roller fairleads it is
recommended that a flip up license plate kit is fitted.
Do not tighten

20 Gateway Drive, Carrum Downs, VIC, 3201
1800 806 952
www.uneek4x4.com.au
Revised: 08/08/2019