Uniden App Cam Solo Pro Series User manual

App Cam Solo Pro
Series
Quick Start Guide

What’s in the Box
Screw Kit
x1
Micro USB Cable
x1
Straping Mount
App Cam Solo Pro
x1
Magenetic Mount
x1
Metal Mount
x1
Quick Start Guide
x1
Mounting Template
x2
x1
Reset Needle
x1
1

2
General Introduction
Red LED (WiFi connection failed)
Blinking: Standby status
On: Working status
Blue LED (WiFi connection succeeded)
Blinking: Standby status
On: Working status
Built-in Mic
Status LED
Lens
Daylight Sensor
Built-in PIR Sensor
Reset Hole
Press more than 5 seconds to restore
the device to factory settings
Power Switch
Micro SD Card Slot
Speaker
Micro USB Power Port
Battery Status LED
Spotlight

3
Charge the Battery
There is a status LED under the micro USB port of the camera, indicating the battery charging status.
Green LED: Fully charged Orange LED: Charging
LED Battery Status
* The battery is built-in,please do not remove it from the camera.
* Please note that the USB charger and Solar Panel are NOT included in the package. You can buy the
solar panel separately.
1. Charge the battery with a
power adapter.
2. Charge the camera with
Uniden solar panel.
Note:
If the camera will not be in use for
a very long time, it’s suggested to
turn it off.
Turn on the Camera
The camera is turned off by default, please turn it on before setting up the camera.

4
App Cam Solo Pro is not designed for 24/7 full capacity running or around-the-clock live streaming.
It’s designed to record motion events and remotely view live streaming only when you need it.
1. Please charge the rechargeable battery with a standard and high-quality DC 5V or 9V battery charger.
2. If you want to power the battery via the solar panel, please note that the battery is ONLY compatible with SPS-01/
SPS-02 solar panel. You cannot charge the battery with other solar panel brands.
3. Please charge the battery in temperatures between 0°C and 45°C.
4. Always use the battery in temperatures between -20°C and 60°C.
5. Please keep the USB charging port dry, clean and free of any debris and make sure the battery contacts are aligned.
6. Always make sure the USB charging port is clean.
7. Please cover the USB charging port with the rubber plug after the battery has been fully charged.
8. Never charge, use or store the battery near any ignition sources, such as re or heaters.
9. Always store the camera in a cool, dry and ventilated environment.
10. Never store the camera with any hazardous or combustible objects.
11. Do keep the battery away from children.
12. Do not short-circuit the battery by connecting wires or other metal objects to the positive (+) and negative (-)
terminals. Do NOT transport or store the battery with necklaces, hairpins or other metal objects.
13. Do NOT disassemble, cut, puncture, short-circuit the battery, or make it dispose of in water, re,microwave ovens and
pressure vessels.
14. Do NOT use the battery if it gives off an odor, generates heat, becomes discolored or deformed, or appears abnormal
in any ways. If the battery is being used or charged, remove the battery from the device or the charger immediately,
and stop using it.
15. Always follow the local waste and recycle laws when throwing the used battery away.
Important Safeguards on Rechargeable Battery Use
!

5
Install Uniden Solo App
Set up the Camera
There are two ways to get the Uniden Solo App:
• Search “Uniden Solo” in App Store (for iOS),
download and install the app.
• Search “Uniden Solo” in Google Play (for Android),
download and install the app.
Please follow the prompt tone to
congure the camera
Camera has been started
up. Please run app, add the
camera and set it up.
1. Please tap the “ ” button in the
top right corner to add the camera.

6
2. Scan the QR code on the back
of the camera.
3. Tap “WiFi Not Congured”
to continue.
Note:
When the setup for the
camera is completed, your
family can access the cam-
era simply by clicking “WiFi
Already Congured” without
reconguring it.
App Cam Solo Pro Camera
can only connect to 2.4GHz
Wi-Fi.

7
4. Select “I have heard the voice prompt”
and tap “Next” to enter the next page.
If you did not hear the voice prompt, please
press “I didn’t hear the voice prompt” for help.
5. Enter the Wi-Fi password of the selected
Wi-Fi network and tap “Next” to continue.

8
6. Tap “Scan Now” to proceed. A QR code will be generated on the phone. Please place the QR
code on your phone towards App Cam Solo Pro camera’ lens at a distance of about 20cm to let
the camera scan the QR code. Please make sure that you’ve ripped the protection lm of the
camera’s lens.
Note: To help scanning, please tap the QR code to display in full screen
Scan succeeded. Camera is connecting to the router. Please wait.

9
7. If you hear the above voice prompt, please
press “I heard ‘Wi-Fi connection failed’ ”
for help.
Connection to the router failed!
8. If you hear the above voice prompt, please
press Select “I have heard the voice prompt”
and tap “Next” to enter the next page.
to nish the quick setup.
Connection to the router succeeded.

10
9. Create a password (at least 6 characters), name the camera and set the DST time. Then start live
view or go to “Device Settings” for more congurations.
Note:
“Name your camera” eld refers to the display name of the camera rather than the login username.

11
Device Menu
Menu
Add New Device
Enable/Disable PIR Motion Sensor
(the PIR sensor is enabled by default)
Device Settings
Access Live View
Battery Status

12
Note:
Higher sensitivity offers longer detecting distance, but it would lead to more false alarms.
You are advised to set up the sensitivity level to “Low” or “Mid” when you install the camera outdoors.
Attention for Camera Installation
The PIR detection range can be customized to meet your specic needs.
You can refer to the following table to set it up in the Uniden Solo App.
Sensitivity Value
Detecting Distance
(For moving and
living things)
Detecting Distance
(For moving vehicles)
Low 0 - 50 Up to 4 meters Up to 10 meters
Mid 51 - 80 Up to 6 meters Up to 12 meters
High 81 - 100 Up to 10 meters Up to 15 meters
• PIR Sensor Detecting Distance

13
Pease install the camera 2-3 meters
above the ground. The detection range of
the motion sensor would be maximized at
such a height.
For effective motion detection, please install
the camera angularly and the angle
between the PIR sensor and the detected
object must be larger than 10°.
Due to the limitation of PIR sensor
detection, if a moving object approaches
the PIR sensor vertically (the direction of the
orange arrow in the image), the camera
may fail to detect motion.
• PIR Sensor Installation Angle
B
θ
Mounting Height:
2-3 Meters
PIR Detecting Distance:
2-10 Meters
A

For reducing false alarms, please note that:
• Do not install the camera facing any objects with bright lights, including sunshine,
bright lamplights, etc.
• Do not place the camera too close to a place where there are frequently moving
vehicles. The recommended distance between the camera and the vehicle is
15 meters
• Stay away from the outlets, including the air conditioner vents, humidier outlets,
the heat transfer vent of projectors, etc.
• Do not install the camera facing the mirror.
• Do not install the camera where there are strong winds
• Keep the camera at least 1 meter away from any wireless devices, including Wi-Fi
routers and phones in order to avoid wireless interference.
Important Notes for Reducing False Alarms
!
14

How to Install Magnetic Mount
Step 3
Screw the magnet to the camera.
Step 1
Rotate to separate parts of
the bracket.
Step 2
Drill holes in accordance with the mounting hole template and
screw the mount to the wall.
Screw the base of the camera bracket onto the wall and then
attach the other part of the bracket onto the base.
15

16
How to Install Metal Mount
Step 4
Attach the camera on the wall mount and twist the
camera in any direction you want.
Step 1
Rotate to separate parts of
the bracket.
Step 2
Drill holes in accordance with the mounting hole template and
screw the security to the wall.
Screw the base of the camera bracket onto the wall and then
attach the other part of the bracket onto the base.

17
Step 4
Adjust the camera angle, and
get the best viewing angle when
you see the live feed in the
Uniden Solo App.
Step 5
Secure the camera by turning
the part on the bracket identied
in the image clockwise.
NOTE:
In case you will need to adjust the camera angle later, please loosen the bracket by turning the upper
part anti-clockwise.
Step 3
Screw the camera to the
bracket.
How to Install Mounting Strap
Thread the loop strap through the
slots and fasten the strap.
It is the best way to attach the
camera to a tree.

Camera is not turning on
If your camera is not turning on, please apply the following solutions:
• Make sure you’ve turned the power button on.
• Charge the camera with a DC 5V/2A power adapter. When the green light is on, the battery is fully charged.
Fail to scan the QR code on the phone
If the camera failed to scan the QR code on your phone, please apply the following solutions:
• Remove the protective lm on the lens of the camera.
• Wipe the camera lens with a dry paper/ towel/tissue.
• Vary the distance (about 30cm) between your camera and the mobile phone which enables the camera to
focus better.
• Increase the phone screen brightness and try scanning the QR code.
Wi-Fi connection failed during the initial setup process
If the camera fails to connect to Wi-Fi, please apply the following solutions:
• Please make sure the band of the Wi-Fi network meet the requirement of the camera.
• Please ensure you have entered the correct Wi-Fi password.
• Put your camera close to your router to ensure a strong Wi-Fi signal.
• Change the encryption method of the Wi-Fi network to WPA2 -PSK/WPA -PSK (safer encryption) on your
router interface.
• Change your Wi-Fi SSID or password and make sure that SSID is within 31 characters and password is within
64 characters.
• Set your password using only the characters on the keyboard.
Troubleshooting
18

Video & Audio
Model App Cam Solo Pro
Image Sensor Starlight CMOS Image Sensor
Video Resolution 1920 x 1080 (2.0Megapixel) 15 fps
Video Compression H.264
Viewing Angle Diagonal: 120°
PIR Detecting Distance Up to 10 meters
PIR Detecting Angle Horizontal: 100°
Night Vision Up to 10 Meters
Audio Two-way talk
Alerts PIR
WiFi
WiFi 2.4 GHz IEEE 802.11b/g/n
Wireless Security WPA-PSK/WPA2-PSK
Hardware
Battery Lithium battery/3.6V, 5200mAh
Spotlight 6500K, 230lm
Storage Supports up to 64GB micro SD card, min class 10
Other
Parameters
Temperature Operating Temperature : -10°C~+55°C
Size & Weight 121 x 90 x 56 m, 330g
Waterproof Level IP65 Weatherproof
Specications
19